Ask or Answer

🏠 Home🏷️ Tags❔ Ask a Question✔️ Answer a QuestionUsers
160 views
Explain flyback converter and draw its waveforms.

Please log in or register to answer this question.

1 Answer

Answer :

Flyback converter:

A flyback converter is used for getting DC output and for isolating input mains and output voltage. A flyback converter is like a buck-boost converter with input and output isolated. There are two modes in flyback converter one is continuous mode and second is discontinuous mode. The discontinuous mode flyback converter is used for those applications which require constant current. And continuous mode flyback converter is use for those applications which requires constant voltage.

 Flyback converter consists of one controllable switch like MOSFET. And power transformer, diode, and capacitor. The efficiency of flyback converter is low due to the power transformer. The output inductor is absent in flyback converter which is advantageous for cost and size. During the on time of controllable switch the transformer stores the energy and during the off time transformer transfer the energy to load.

image

image image

image

Like 0 like

Related Questions

95 views

Description : Explain buck or step down converter and draw its waveforms.

Last Answer : Buck converter or Step down converter: Buck converter is a step-down converter. The buck converter step-down the output voltage and step up the output current. Buck converter is a DC to DC converter. ... load. The output voltage is controlled by controlling on period and off period.

1 answer
231 views

Description : Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

Last Answer : Full bridge converter: Full bridge converter provides isolation between input and output. Full bridge converter is used for step up or step down the input voltage. Full bridge converter consists of four power semiconductor ... Require filter on both input and output.

1 answer
239 views

Description : Explain buck boost converter and draw its waveforms.

Last Answer : Buck-Boost converter: The buck-boost converter consists of a transistor for switching purpose, diode, inductor, and capacitor. Buck-boost converter is the combination of the buck converter and boost ... In buck-boost converter both input current and diode current are discontinuous.

1 answer
54 views

Description : Draw circuit diagram of symmetrical configuration of bridge converter.

Last Answer : circuit diagram of symmetrical configuration of bridge converter

1 answer
350 views

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

1 answer
531 views

Description : Give the effect of source impedance on converter operation.

Last Answer : Effect of source impedance on converter operation: For single-phase fully controlled bridge converter, the SCRs are triggered in pairs alternately. During positive half-cycle of input, SCRs T1 and T2 are triggered ... increases and as a consequence, the output dc voltage decreases. 

1 answer
2,750 views

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

2 answers
174 views

Description : The percent resolution of an 8 -bit D/A converter is

Last Answer : The percent resolution of an 8 -bit D/A converter is 0.392

1 answer
241 views

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

2 answers
136 views

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

1 answer
139 views

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

1 answer
Show MoreAsk QuestionNext Page →