search
person

what happens when ammeter is connected in parallel?

by

1 Answer

Ammeter is a current measuring device having low internal resistance so as to direct all the current flowing in the circuit through it. Hence Ammeter is always connected in series with the circuit.
If Ammeter is connected in parallel with the circuit, then the circuit is bypassed.
If Ammeter is connected in parallel with the supply, then the supply will be a short circuit.
thumb_up_alt 1 like thumb_down_alt 0 dislike
by
by
Awesome answer
by
Thank you Nayeem
by
Nice answer bro

Related questions

The function of shunt in an ammeter is to?

Answer : The function of shunt in an ammeter is to by pass the current.

An ammeter is a?

Answer : An ammeter is a secondary instrument.

can ammeter measure ac?

Answer : Yes it can...

what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Answer : equivalent resistance

When three resistors with unequal values are connected in parallel, _______

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

What should be the ideal resistance of ammeter ?

Description : What should be the ideal resistance of ammeter ?

Answer : Ideal resistance of ammeter should be zero.

what is ammeter ?

Description : what is ammeter ?

Answer : An instrument that is used to measure the amount of current flowing in a circuit.

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Description : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Answer : Practical Significance In the industry environment Electrical Engineering diploma graduate are expected to measure basic parameters like voltage, frequency, time period etc. for R-L series circuits. Therefore ... /varying L. 7. Draw the phasor diagram for each of reading for verification.

With three resistances connected in parallel, if each dissipates 20 W the ...

Description :  With three resistances connected in parallel, if each dissipates 20 W the total power supplied by the voltage source equals?

Answer : Power is the only thing which is additive in both connection whether it is parallel or series connection so total power consumed will addition of all individual power =20+20+20 = 60 watt

Write any two disadvantages of ammeter shunts.

Description : Write any two disadvantages of ammeter shunts.

Answer : Disadvantages of ammeter shunts: 1. Errors are caused because of change in temperature. 2. Most suitable for DC measurement. 3. Power loss takes place.

With neat diagram, explain the working of clip-on ammeter.

Description : With neat diagram, explain the working of clip-on ammeter.

Answer : Working of Clip on Ammeter: Clip on ammeters are used to measure the high current flowing through bus bar, cable or fuse holders, which act as primary. It consists of split core current ... then clipped over the current carrying conductor. The dial will record the current directly. 

Describe procedure for calibration of ammeter with diagram.

Description : Describe procedure for calibration of ammeter with diagram.

Answer : Procedure for Calibration of Ammeter:  In this method, DC potentiometer is used for measurement of voltage across a standard low resistance.  Connect the circuit as shown in the figure, ... S = resistance of potentiometer  And the currents are compared for finding out error in ammeter.

How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Description : How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Answer : Extension of A.C. Ammeter Range: The range of a.c. ammeter can be extended by using CT, the arrangement is shown in figure. The CT is current transformer having less number of primary turns carrying high ... high magnitude of source voltage. In this way range of a.c. voltmeter can be extended.

State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Description : State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Answer : Phase Sequence Indicator:  1. For finding correct phase sequence of supply  2. For obtaining exact instant of parallel operation of alternators.  3. For obtaining reversal of rotation ...  4. In electroplating industries   5. In various processes industries for measuring power factor

Draw a typical electric circuit including ammeter and voltmeter.

Description : Draw a typical electric circuit including ammeter and voltmeter.

Answer : The figure shows typical electric circuit including ammeter and voltmeter. Ammeter is connected in series for measurement of current. Voltmeter is connected in parallel for measurement of voltage. Fuse is use ... are used. If the electric supply is DC the DC ammeter and DC voltmeter are used.

When one leg of parallel circuit is opened out the total current will?

Description : When one leg of parallel circuit is opened out the total current will?

Answer : When one leg of parallel circuit is opened out the total current will decrease.

State the principle of solar cell. What is necessity of series and parallel connection of solar cells.

Description : State the principle of solar cell. What is necessity of series and parallel connection of solar cells.

Answer : Principle of solar cell:-  Working:- Solar cell operates on principle of Photo-voltaic effect Solar cell works in following steps:  The solar cell is composed of a P-type ... of Voltage & Current rating it is necessity of connecting series and parallel connection of solar cells.

XL and XC in parallel

Description : XL and XC in parallel

Answer : https://youtu.be/fCN95EiEWDI

In parallel RLC resonance circuit at resonance the current will be

Description : In parallel RLC resonance circuit at resonance the current will be  (1) Minimum (2) Maximum (3) Zero (4) Infinite

Answer : In parallel RLC resonance circuit at resonance the current will be Minimum 

While keeping the excitation constant, if the steam supply of an alternator running in parallel with another

Description : While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then (A) It would over-run the other alternator (B) Its rotor ... (C) Its portion of share in load will increase (D) Its power factor would be decreased.

Answer : While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then Its portion of share in load will increase

Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Description : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open?

Answer : Three 60 W bulbs are in parallel across the 60 V power line. If one bulb burns open the other two bulbs will light.

If a parallel circuit is opened in the main line, the current?

Description : If a parallel circuit is opened in the main line, the current?

Answer : If a parallel circuit is opened in the main line, the current is zero in all branches.

An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel...

Description : An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

Answer : An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms, both resistance and inductance carry equal currents.

The series and parallel resonance on L-C circuit differs in that?

Description : The series and parallel resonance on L-C circuit differs in that?

Answer : The series and parallel resonance on L-C circuit differs in that series resistance needs a low-resistance source for sharp rise in current.

A parallel AC. circuit in resonance will?

Description : A parallel AC. circuit in resonance will?

Answer : A parallel AC. circuit in resonance will have a high impedance.

The power factor at resonance in R-L- C parallel circuit is?

Description : The power factor at resonance in R-L- C parallel circuit is?

Answer : since a rlc circuit at resonance behaves like a pure resistive circuit, i.e there is no phase difference between current and voltage, hence the power factor is unity.

Two non-collinear parallel equal forces acting in opposite direction?

Description : Two non-collinear parallel equal forces acting in opposite direction?

Answer : Two non-collinear parallel equal forces acting in opposite direction constitute a couple.

Is more power dissipated in series or parallel?

Description : Is more power dissipated in series or parallel?

Explain with neat diagram series and parallel magnetic circuits.

Description : Explain with neat diagram series and parallel magnetic circuits. 

Answer : Series magnetic circuit: When different magnetic materials having different lengths, cross sectional areas and permeability are connected one after another, in which same flux is established in different sections, then it is called series ... flux, Φ = Φ1 + Φ2  Path 1: BAFE  Path 2: BACD

A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Description : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Answer : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Series parallel resistances problem solution

Description : Series parallel resistances problem solution

Answer : Series parallel resistances problem solution

Parallel rc circuit

Description : Parallel rc circuit

Answer : Parallel rc circuit

Parallel circuit rules

Description : Parallel circuit rules

Answer : Parallel circuit rules

Parallel Reactance and Resistance Example 1

Description : Parallel Reactance and Resistance Example 1

Answer : Parallel Reactance and Resistance Example 1

Series and parallel capacitor problem

Description : Series and parallel capacitor problem

Answer : Series and parallel capacitor problem 1 : https://youtu.be/MSl5mRwtjAE Series and parallel capacitor problem 2 : https://youtu.be/yGwbpyEtIyw Series and parallel capacitor problem 3 : https:// ... https://youtu.be/_7KwEwWqiNU Series and parallel capacitor problem 10 : https://youtu.be/et8MCWV_OyE

State necessity of series connection and parallel connection of batteries.

Description : State necessity of series connection and parallel connection of batteries.

Answer : Necessity of series connection of batteries: 1. The batteries are available with some specific terminal voltages. e. g. 6V, 12V, 24V, 48V etc. 2. If we want to have some terminal voltage other than ... batteries of capacities I1, I2, I3, I4 . are connected in parallel, all having identical emfs.

An additional condition for parallel operation of three-phase transformers over single-phase transformers is that

Description : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that

Answer : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that the transformers should belong to the same vector group

Explain parallel and wireless protocols.

Description : Explain parallel and wireless protocols.

Answer : Parallel protocols: PCI bus (Peripheral Components Interconnect): PCI stands for Peripheral Components Interconnect. PCI bus is used as a communication line to transmit signals and data ... provide the basis for wireless network products using the Wi-Fi brand.

At ______ frequencies the parallel R-L circuit behaves as purely resistive.

Description : At ______ frequencies the parallel R-L circuit behaves as purely resistive.

Answer : At very high frequencies the parallel R-L circuit behaves as purely resistive.

The purpose of a parallel circuit resonance is to magnify?

Description : The purpose of a parallel circuit resonance is to magnify?

Answer : The purpose of a parallel circuit resonance is to magnify voltage.

For the parallel operation of two or more D.C. compound generators, we should ensure that?

Answer : For the parallel operation of two or more D.C. compound generators, we should ensure that series fields of all generators should be either on positive side or negative side of the armature.

For the parallel operation of single phase transformers it is necessary that they should have?

Answer : Necessary conditions required to be satisfied in order to ensure successful parallel operation of single phase transformers:  1. Only transformers having the same phase displacement between primary and secondary ... . 7. The phase sequence must be followed strictly on HV and LV side connection.

parallel operation of mosfet can be done more easily as compared to thyristor. why?

Description : parallel operation of MOSFET can be done more easily as compared to thyristor. why?

Answer : Parallel operation of MOSFET can be done more easily as compared to thyristor because the resistance of MOSFET is increases with increase in temperature. MOSFET have the positive temperature coefficient. In ... the parallel operation of MOSFET can be done more easily as compared to the thyristor.

Explain the series and parallel operation of MOSFET. Which is suitable and why ?

Description : Explain the series and parallel operation of MOSFET. Which is suitable and why?

Answer : Series operation of MOSFET: To increase voltage handling capability MOSFETs are connected in series. When the MOSFETs are connected in series each MOSFET should turn on and turn off ... on and turn off time and transconductance. Each MOSFET should share current equally.  

explain the parallel operation of IGBT?

Description : Also, highlight the problem faced during parallel operation.

Answer : Parallel operation of IGBT: Parallel operation of IGBT is done for obtaining high current rating. Paralleling of IGBT reduces conduction losses and thermal stress. IGBT combines the qualities of ... . IGBTs must share losses equally otherwise IGBT may get failure due to thermal differences.

Flash or Parallel ADC

Description : Flash or Parallel ADC

Answer : Flash or Parallel ADC

What will happen if a voltmeter is connected like an ammeter in series of the load ?

Description : What will happen if a voltmeter is connected like an ammeter in series of the load ? (a) The meter will burn out. (b) The measurement will be too high. (c) The same current will flow as would have been with ammeter in circuit. (d) There will be almost no current in the circuit. 

If a voltmeter is connected, like an ammeter in series to the load:

Answer : If a voltmeter is connected, like an ammeter in series to the load: Almost no current will flow in the circuit

Two transformers do not have equal percentage impedance. This is likely to result in?

Description : Two transformers are connected in parallel. These transformers do not have equal percentage impedance. This is likely to result in?

Answer : Two transformers are connected in parallel. These transformers do not have equal percentage impedance. This is likely to result in loading of the transformers not in proportion to their kVA ratings.

← Prev Question Next Question →
editAsk a Question
...