Related questions

Description : Why is the armature of DC generator laminated?

Answer : The armature of DC generator is laminated to reduce eddy current losses.

Answer : The armature core of a D.C. generator is usually made of silicon steel.

Answer : The demagnetising component of armature reaction in a D.C. generator reduces generator e.m.f.

Description : A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

Answer : A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is 0.87

Answer : A sinusoidal voltage of 5 Hz is applied to the field of a shunt generator. The armature voltage wave will be of 5 Hz.

Answer : Armature reaction in a generator results in demagnetisation of leading pole tip and magnetisation of trailing pole tip.

Description : For a D.C. generator when the number of poles and the number of armature conductors is fixed, then which winding will give the higher e.m.f. ?

Answer : Wave winding

Description : The armature reaction in a synchronous generator supplying leading power factor load is (A) magnetizing (B) demagnetizing (C) demagnetizing and cross-magnetizing (D) magnetizing and cross-magnetizing

Answer : The armature reaction in a synchronous generator supplying leading power factor load is magnetizing and cross-magnetizing

Answer : Open circuited armature coil of a D.C. machine is identified by the scarring of the commutator segment to which open circuited coil is connected and indicated by a spark completely around the commutator.

Description : Why poles of dc machine are laminated?

Answer : Poles of DC machines are laminated to reduce the eddy current losses in the poles.

Answer : In a D.C. generator, the critical resistance refers to the resistance of field.

Answer : If a D.C. generator fails to build up the probable cause could not be field resistance less than the critical resistance.

Answer : The e.m.f. generated in a D.C. generator is directly proportional to speed of armature.

Answer : If brushes of a D.C. generator are moved in order to bring these brushes in magnetic neutral axis, there will be crossmagnetisation as well as demagnetising.

Answer : The critical resistance of the D.C. generator is the resistance of field.

Description : If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be?

Answer : If residual magnetism is present in a D.C. generator, the induced e.m.f. at zero speed will be zero.

Answer : A 220 V D.C. generator is run at full speed without any excitation. The open circuit voltage will be about 2 V.

Answer : In a level compounded D.C. generator, full load terminal voltage is equal to no-load terminal voltage.

Answer : In a D.C. generator in case the resistance of the field winding is increased, then output voltage will decrease.

Answer : A D.C. generator can be considered as rotating amplifier.

Answer : Flashing the field of D.C. generator means creating residual magnetism by a D.C. source.

Answer : In a D.C. generator the magnetic neutral axis coincides with the geometrical neutral axis, when there is no load on|he generator.

Answer : In a D.C. generator the number of mechanical degrees and electrical degrees will be the same when number of poles is 2.

Answer : D.C. generator generally preferred for charging automobile batteries is long shunt compound generator.

Answer : In a D.C. generator the ripples in the direct e.m.f. generated are reduced by using carbon brushes of superior quality.

Answer : Magnetic field in a D.C. generator is produced by electromagnets.

Answer : In case of a 4-pole D.C. generator provided with a two layer lap winding with sixteen coils, the pole pitch will be 8.

Answer : In a D.C. generator, the iron losses mainly take place in armature rotor.

Answer : The condition for maximum efficiency for a D.C. generator is variable losses equal to constant losses.

Answer : The total losses in a well designed D.C. generator of 10 kW will be nearly 500 W.

Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Description : The normal value of the armature resistance of a d.c. motor is?

Answer : The normal value of the armature resistance of a d.c. motor is 0.5.

Answer : When the armature of a D.C. motor rotates, e.m.f. induced is back e.m.f.

Answer : The armature voltage control of D.C. motor provides constant torque drive.

Answer : In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be more than full-load current.

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

Description : In dc machines, the armature windings are placed on the rotor because of the necessity for  (1) electromechanical energy conversion (2) generation of voltage (3) commutation (4) development of torque

Answer : 3  Commutation

Description : The induced emf in the armature of a lap -wound four -pole dc machine having 100 armature conductors rotating at 600 rpm and with 1 Wb flux per pole is  (1) 1000V (2) 100V (3) 600V (4) 10,000V

Answer : The induced emf in the armature of a lap -wound four -pole dc machine having 100 armature conductors rotating at 600 rpm and with 1 Wb flux per pole is 1000V

Description : Aluminium is not used as winding wire for the armature of a dc machine because  (1) aluminium has low resistivity (2) a large winding space is taken by aluminium conductors and creates ... ) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Answer : Aluminium is not used as winding wire for the armature of a dc machine because  (2) a large winding space is taken by aluminium conductors and creates jointing problems (3) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Description : Armature control of DC motor

Answer : Armature control of DC motor

Answer : In a separately excited generator supplying rated load the armature reaction is always present.

Description : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

Answer : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be 580 V.

Answer : In D.C. generators on no-load, the air gap flux distribution in space is flat topped.

Description : The fall in speed of a dc generator due to increase in load can be corrected by  (1) cooling the armature.. (2) increasing the excitation. (3) reducing the load voltage. (4) increasing the input to the prime mover

Answer : It   can  be  corrected  by  increasing  the  input  to  the  prime  mover.

Answer : Armature reaction of an unsaturated D.C. machine is crossmagnetising.

Description : Laminated cores, in electrical machines, are used to reduce?

Answer : Laminated cores, in electrical machines, are used to reduce eddy current loss.

Description : In AC. circuits, laminated iron is invariably used in order to?

Answer : In AC. circuits, laminated iron is invariably used in order to reduce eddy current loss.

Description : Why does the core of a transformer need to be laminated?

Answer : Transformer cores are laminated to reduce eddy current loss.

Description : State the function of commutator in DC generator and name the material used for commutator.

Answer : Function of Commutator: Commutator converts AC induced in armature winding into DC for external load. Material: i) Commutator segments are made up of Copper. ii) Commutator segments are insulated from each other by Mica.

← Prev Question Next Question →
Ask a Question
Choose topic