1 Answer

The ratio of starting torque to full-load torque is least in case of shunt motors.

Like 0 like Dislike 0 dislike
It is in order
Diff compound ,shunt, cumulative,series

Related questions

Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

Description : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Answer : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to : Z (p.u)

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Answer : Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of D.C. series motor.

Answer : Capacitor start motor has high torque in starting

Description : Why a dc series motor has a high starting torque?

Description : Why high starting torque is required?

Description : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Answer : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

Answer : The standard full-load power factor ratings for synchronous motors are unity or 0.8 leading.

Answer : The starting winding of a single-phase motor is placed in stator.

Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Answer : The starting resistance of a D.C. motor is generally low.

Answer : A direct online starter is used for starting motors up to 5 H.P.

Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

Description : How is a three phase cage induction motor self starting?

Answer : Any type of induction motor is self starting. Because the reason for torqe production require two flux displaced by some angle theta.If theta is constant with time then torqe will be constant;if ... torqe also pulsating. In induction motor this angle theta is not pulsating.so it is self starting 

Description : Is induction motor is self starting?

Answer : Single phase induction motor is not self starting. Three phase induction motor is self starting.

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

Answer : In repulsion motor, maximum torque is developed when brush axis is at 45° electrical to the field axis.

Description : Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop

Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

Description : What is the formula of torque?

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Description : Explain starting system in diesel electric power plant.

Answer : Starting system in Diesel Electric Power Plant: It includes Storage battery, compressed air tanks, self-starter etc. The purpose of engine starting system is to rotate the engine initially while ... as Ammeters, Voltmeters, Wattmeters, Thermometers, Pressure gauges, Visible and audible alarm etc.

Answer : In a capacitor start motor, the phase displacement between starting and running winding can be nearly 90°.

Description : List different starting methods of three phase synchronous motor. Explain any one of them.

Answer : Different Starting Methods of Three Phase Synchronous Motor: As synchronous motor is not self starting, different methods of starting are as follows: 1) By using an Induction (Pony) motor 2) ... . The rotor gets pulled into synchronism and starts running at constant speed as a synchronous motor. 

Description : State the functions of following elements: i) Diesel engine system ii) Air intake system iii) Engine exhaust system iv) Engine starting system.

Answer : i) Diesel engine system:-  Four strokes Two strokes ii) Air intake system:- Air intake system is provided to supply air to engine cylinder for fuel combustion.  iii) Engine exhaust system ... provided to rotate the engine initially until the firing starts and engine run under its own power. 

Answer : The value of starting capacitor of a fractional horse power motor will be 300 uF .

Answer : The rotor developed by a single-phase motor at starting is zero.

Description : A synchronous motor can be made self starting by providing?

Answer : A synchronous motor can be made self-starting by providing damper bar.

Description : Why starter is required for starting an induction motor?

Description : Why does induction motor have high starting current?

Answer : In induction motor , the flux produce is quadrature to the applied voltage. Since when we are going to start motor , there is no flux present inside . So in order to lets say compensate it ... times of current to further increase flux. So that is reason for high starting current in induction motor

Description : Which of the following plants will take least time in starting from cold conditions to full-load operation? A) Nuclear power plant B) Steam power plant C) Hydro-electric power plant D) Gas turbine plant

Answer : Hydro -electric power plant

Description : An induction motor having full load torque of 60 Nm when delta connected develops a starting torque of 120 Nm. For the same supply voltage if the motor is changed to star connection, the starting torque developed will be  A) 40 Nm B) 60 Nm C) 90 Nm D) 120 Nm

Answer : An induction motor having full load torque of 60 Nm when delta connected develops a starting torque of 120 Nm. For the same supply voltage if the motor is changed to star connection, the starting torque developed will be 40 Nm

Description : The meter which does not have any component in it to provide control torque is (A) Electrodynamometer for current measurement (B) Electrodynamometer for voltage measurement (C) Electrodynamometer for power measurement. (D) Electrodynamometer for power factor measurement.

Answer : The meter which does not have any component in it to provide control torque is Electrodynamometer for power factor measurement.

Description : The torque produced in wattmeter is proportional to

Answer : A

Description : List the different methods to produce damping torque.

Answer : Methods of providing damping torque in indicating type instruments: 1) Air friction damping. 2) Fluid friction damping. 3) Eddy current damping.

Description : Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Answer : A)Spring control method: As shown in the figure, the inner ends of the both springs are attahced to the spindle, while outer end of upper spring is attached to the lever and outer ... of spring material: 1.Non Magnetic material 2.Low specific resistance 3.Low temperature coefficient of resistance

Description : Name the different torque and their function in measuring instrument.

Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / restraining torque.  3. Damping torque.  1. Deflecting torque:  - To create deflection of pointer ... .  - Bring the pointer to standstill quickly.  - To minimize oscillations about final position. 

Description : State the function of controlling torque in electrical measuring instrument.

Answer : Function of controlling torque  1. The function is to opposes the deflection force and increases with the increase in the deflection of the moving system, to limit its movement. 2. and brought ... set a position where the two opposing forces i.e. deflection and controlling forces are equal. 

Answer : In a meggar controlling torque is provided by coil.

Answer : In a portable instrument, the controlling torque is provided by spring.

Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

Description : What is the maximum value of torque angle in synchronous motor?

Answer : The maximum value of torque angle in synchronous motor is 90 degrees electrical.

Description : DC motor gross torque example

Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

← Prev Question Next Question →
Ask a Question
Choose topic