1 Answer

In D.C. machines fractional pitch winding is used to reduce the sparking.

Like 0 like Dislike 0 dislike

Related questions

Description : State advantages of short pitch winding over full pitch winding in alternators. 

Answer : Advantages of Short Pitch Winding over Full Pitch Winding in Alternators: 1) Short pitching reduces the amount of copper needed for end connection when compared with full pitched coil. 2) They ... reduced, thereby increasing the efficiency. 4) The power quality of generated emf is improved. 

Answer : In the case of lap winding resultant pitch is difference of front and back pitches.

Description : A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and front pitch adopted could be respectively

Answer : A 36 slot, 4 -pole, dc machine has a simplex lap winding with two conductors per slot. The back pitch and front pitch adopted could be respectively 19,17

Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

Description : A _________ is used to measure the stator % winding temperature of the generator.  (A) Thermocouple (B) Pyrometer (C) Resistance thermometer (D) Thermometer

Answer : A Resistance thermometer is used to measure the stator % winding temperature of the generator. 

Description : Aluminium is not used as winding wire for the armature of a dc machine because  (1) aluminium has low resistivity (2) a large winding space is taken by aluminium conductors and creates ... ) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Answer : Aluminium is not used as winding wire for the armature of a dc machine because  (2) a large winding space is taken by aluminium conductors and creates jointing problems (3) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Answer : In D.C. machines the residual magnetism is of the order of 2 to 3 percent.

Description : In dc machines, the armature windings are placed on the rotor because of the necessity for  (1) electromechanical energy conversion (2) generation of voltage (3) commutation (4) development of torque

Answer : 3  Commutation

Description : Silicon steel is used in electrical machines because it has?

Answer : Silicon steel is used in electrical machines because it has low hysteresis loss.

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

Answer :  Sandwich type winding is used in 3 phase shell-type transformer.

Description : The damping winding in synchronous motor is generally used to?

Answer : The damping winding in synchronous motor is generally used to provide starting torque and prevent hunting.

Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Answer : Most of the fractional horsepower motors have either plain or sleeve bearings.

Description : Compare core type transformer and shell type transformer on the following parameters. (i) Types of winding used, (ii) Application

Answer : Ans:

Answer : Satisfactory commutation of D.C. machines requires brushes should be of proper grade and size, brushes should smoothly run in the holders, smooth, concentric commutator properly undercut.

Answer : Brushes of D.C. machines are made of carbon.

Answer : Hopkinson's test on D.C. machines is conducted at full-load.

Answer : The purpose of retardation test on D.C. shunt machines is to find out stray losses.

Answer : In case of D.C. machine winding, number of commutator segments is equal to number of armature coils.

Answer : The value of starting capacitor of a fractional horse power motor will be 300 uF .

Answer : The type of D.C. motor used for shears and punches is cumulative compound D.C. motor.

Answer : Starters are used with D.C. motors because to restrict armature current as there is no back e.m.f. while starting.

Description : In a dc machine, interpoles are used to  (1) neutralize the effect of armature reaction in the interpolar region (2) generate more induced emf in the armature (3) avoid interference of the armature flux with the main -field flux (4) reduce the demagnetizing effect of armature reaction

Answer : In a dc machine, interpoles are used to neutralize the effect of armature reaction in the interpolar region

Description : The inertia constants of two groups of machines which do not swing together are M1 and M2. The equivalent inertia constant of the system is

Answer : The inertia constants of two groups of machines which do not swing together are M1 and M2. The equivalent inertia constant of the system is M1M2/M1+M2

Description : Draw the connection diagram of long shunt differential D.C. compound generator.

Answer : Ans:

Description : Damper winding in a synchronous motor

Answer : Damper winding in a synchronous motor Serves to start the motor.

Description : Damper winding is provided in 3 phase synchronous motors to :

Answer : Damper winding is provided in 3 phase synchronous motors to : provide starting torque and prevent hunting

Answer : The starting winding of a single-phase motor is placed in stator.

Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Answer : The purpose of stator winding in the compensated repulsion motor is to improve power factor and provide better speed regulation.

Answer : In split phase motor main winding is of thick wire placed at the bottom of the slots.

Description : In synchronous motor, does the winding losses vary with load?

Answer : No, in the synchronous motor the winding losses do not vary with load.

Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

Description : Define transformation ratio in terms of current and voltage.

Answer : (i) Transformation Ratio (K) is defined as the ratio of the primary current to the secondary current.  (ii) Transformation Ratio (K) is defined as the ratio of the secondary voltage to the primary voltage.

Description : State any two applications of single phase autotransformer.

Answer : Applications of single phase auto transformers: 1) Give small boost to distribution cable to correct the voltage drop. 2) As auto transformer starter for induction motors. 3) As furnace supply ... . 5) In control equipment for single phase locomotives. 6) As dimmer in lighting circuits.

Description : State any two conditions for parallel operation of 3-phase transformer.

Answer : Conditions for Parallel operation of 3 phase transformer 1) Voltage ratings of both the transformers must be identical. 2) Percentage or p.u. impedance should be equal in magnitude. 3) X/R ratio ... between primary & secondary voltages must be same. 6) Phase sequence on both sides must be same.

Description : Define: (i) Commercial efficiency of a transformer and  (ii) All day efficiency of a transformer.

Answer : (i) Commercial Efficiency : It is the ratio of output power in watt to the input power in watt. (ii) All day efficiency of a transformer: It is the ratio of output energy in kWh to the input energy in kWh in the 24 hours of the day

Description : A 50 KVA transformer has iron loss 2 kW on full load. Calculate its iron loss at 75% of full load.

Answer : Iron loss is dependent on voltage and independent of load. Hence iron loss at 75% of Load = Iron loss at full load = 2 kW

Description : State any four properties of Ideal transformer.

Answer : Properties of Ideal transformer: 1) No losses (iron and copper losses), hence no temperature rise. 2) No magnetic leakage i.e (Coefficient of coupling between primary and secondary windings is unity) 3) Zero winding ... drop i.e. E1 = V1, E2 = V2 5) Efficiency 100 %. 6) Regulation 0 %.

Description : Fractional pitch windings are used in DC machines to (A) Reduce copper losses (B) Improve cooling (C) Increase the generated emf (D) Reduce sparking

Answer : Fractional pitch windings are used in DC machines to Reduce sparking

Answer : In case of a 4-pole D.C. generator provided with a two layer lap winding with sixteen coils, the pole pitch will be 8.

Answer : The voltage used for suburban trains in D.C. system is usually 600 to 750 V.

Answer : D.C. shunt motors are used for driving machine tools.

Answer : In D.C. generators, lap winding is used for low voltage, high current.

Description : Laminated cores, in electrical machines, are used to reduce?

Answer : Laminated cores, in electrical machines, are used to reduce eddy current loss.

Description : What type of motor is used for drilling machines?

Answer : universal motor also used in Handheld power tools, blowers, blenders, vacuum cleaners, polishers and kitchen appliances.universal motor is defined as a motor which may be operated either on direct or single phase AC supply at approximately the same speed and output

Description : For protection of rotating machines against lightning surges _______ is used.  (1) lightning arrester (2) capacitor (3) combination of lightning arrester and capacitor (4) lightning conductor and arrester

Answer : For protection of rotating machines against lightning surges combination of lightning arrester and capacitor is used. 

Description : How is a thyristor used to convert AC to DC?

← Prev Question Next Question →
Ask a Question
Choose topic