# The rotor slots, in an induction motor, are usually not quite parallel to the shaft because it?

The rotor slots, in an induction motor, are usually not quite parallel to the shaft because it helps in reducing the tendency of the rotor teeth to remain under the stator teeth.

## Related questions

Description : An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is (A) 5.06 kW (B) 0.3 kW (C) 100 kW (D) 83.33 kW

Answer : An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is 83.33 kW

Description : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in ... increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

Answer : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then the flux first decreases and then increases in the same direction

Description : A 3-phase, 4-pole, 50Hz induction motor runs at a speed of 1440 rpm. The rotating field produced by the rotor rotates at a speed of ________ rpm with respect to stator field. (A) 1500 (B) 0 (C) 1440 (D) 60

Answer : Reason is kinetic energy

Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Description : A change of 4% in the supply voltage to an induction motor will produce a change of approximately

Answer : A change of 4% in the supply voltage to an induction motor will produce a change of approximately 8% in the rotor torque

Description : In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

Answer : In an induction motor if the flux density is reduced.to one-half, of its normal value then the torque will reduce to one-fourth

Description : Explain with neat circuit diagrams the procedures to perform no load and blocked rotor tests on three phase induction motor.

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm

Description : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω

Answer : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is 0.3 Ω

Description : In a split-phase induction motor, the resistance/reactance ratios of windings are such that (A) current in the auxiliary winding leads the current in the main winding (B) current in the ... (C) both windings develop the same starting torque (D) both windings develop high starting current

Answer : In a split-phase induction motor, the resistance/reactance ratios of windings are such that current in the auxiliary winding leads the current in the main winding

Answer : Single phase induction motor usually operates on 0.6 power factor lagging.

Answer : The power factor of a single-phase induction motor is usually lagging.

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Description : What is mean by plugging in three phase induction motor?

Answer : Plugging in three-phase induction motor means interchanging of any two phases of a stator for quick stopping.

Description : Split phase induction motor

Answer : Split phase induction motor : There are two windings used in split phase induction motor. It is a type of single-phase induction motor. There are two winding one is called main winding and ... motor have low starting torque it is used for small fans, blowers, centrifugal pumps, grinders etc.

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases

Description : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is

Answer : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 4 percent

Description : A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for

Answer : A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for 4 poles

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

Answer : If a single phase induction motor runs slower than normal, the most likely defect is worn bearings.

Description : How is a three phase cage induction motor self starting?

Answer : Any type of induction motor is self starting. Because the reason for torqe production require two flux displaced by some angle theta.If theta is constant with time then torqe will be constant;if ... torqe also pulsating. In induction motor this angle theta is not pulsating.so it is self starting

Description : How does a single phase induction motor work?

Answer : As we know that single phase induction is not self started because for self started we require atleast two revolving field but single phase induction motor has only one. So we provide extra ... 1phase IM classified as split phase IM, capacitor start capacitor run, capacitor start induction run.

Description : Is induction motor is self starting?

Answer : Single phase induction motor is not self starting. Three phase induction motor is self starting.

Description : What is the definition of induction motor?

Answer : its working on magnetic base made by coils and its work with 1 phase or 3 phase ac or dc supply

Description : What is the function of induction motor?

Answer : while you give supply to motor its motor run on magnet base

Description : At which time power factor of the induction motor is low?

Answer : The power factor of the inducction motor is low at the time of starting as compare to while the induction motor is running.

Description : explain the working of single phase induction motor.

Answer : Stator has two winding namely main winding and auxiliary winding.when single phase ac supply is given to the motor,its produces alternating field.this field cut by a cage rotor.so some emf ... due to this emf,rotor flux produced.the interaction between two fluxes produce torque.so rotor rotates.

Answer : Capacitor start motor has high torque in starting

Answer : Induction motor is a AC motor it is also known as asynchronous motor .

Answer : if induction motor rotates exceed than its synchronous speed, it acts as a generator.

Description : Induction motor

Answer : Induction Motor Inductor is a coil of wire which possess the property of inductance. Inductance is the property of an electric conductor which generate electromotive force (EMF ... motor are classified as slip ring induction motor and squirrel cage induction motor.

Description : Single Phase Induction Motor

Answer : Single Phase Induction Motor Single phase induction motor is mostly used in home, office, shop and many single phase appliances like pumps,  ... torque and silent operation. It is uses where silent operation is required.

Description : speed control methods of three phase induction motor?

Answer : Speed control of three phase induction motor

Answer : The repulsion-start induction-run motor is used because of high starting torque.

Description : A synchronous motor has better power factor as compared to that of an equivalent induction motor. This is mainly because?

Answer : A synchronous motor has better power factor as compared to that of an equivalent induction motor. This is mainly because stator supply is not required to produce magnetic field.

Answer : An induction motor has relatively high power factor at near full load.

Description : Why starter is required for starting an induction motor?

Description : The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

Answer : Ns         equals        f/pair pole 50/4      - 12.5

Description : Explain the need and steps to conduct the reduced voltage running up test on the three phase induction motor.

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

Description : State the function of following parts in Induction motor. (i) Stator (ii) Slip rings

Answer : Name of part Function Stator 1) Stator frame supports the core, terminal box and protects the inner parts. 2) Stator core houses stator winding. 3) Stator winding ... ) Provides facility to connect external resistance to rotor circuit through brushes for starting and control.

Description : List the energy conservation technique in induction motor.

Answer : Following are the list of energy conservation techniques in electrical motors: 1) Reduction in iron losses by using low loss silicon steel core material laminated to thinner dimension. 2) Using bigger length ... at light load. 13) By rewinding in induction motor 14) By motor survey

Answer : Energy conservation technique in induction motor by minimizing idle and redundant running of motor: 1) Loss of energy as the no load power drawn is approximately about 12% to 16% of rated ... to unnecessary line losses. 4) Reduction in overall system energy efficiency over period of time.

Description : In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

Answer : In a single-phase induction motor, the operating direction is determined by the Starting circuit

Description : The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be?

Answer : The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be 4.

Description : Explain the working principle of induction motor.

Answer : Working principle of induction motor: * When the motor is excited with three-phase supply, three-phase stator winding carries three-phase currents & produces a rotating magnetic field of constant magnitude and ... , which tend to move the rotor in the same direction as the rotating magnetic field.

Description : Explain the activities carried out during weekly maintenance of 3 ph. Induction motor.

Answer : Activities Carried out During Weekly Maintenance of 3 ph. Induction Motor:  1) Check belt tension. In cases where this is excessive it should immediately be reduces and in the case of sleeve ... and cooled by oil mist systems its important to check the oil mist flow paths/pressure components.

← Prev Question Next Question →