search
person

1 Answer

Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Answer : In repulsion motor, maximum torque is developed when brush axis is at 45° electrical to the field axis.

Answer : The repulsion-start induction-run motor is used because of high starting torque.

Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

Answer : Capacitor start motor has high torque in starting

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

Description : speed control methods of three phase induction motor?

Answer : Speed control of three phase induction motor

Answer : In repulsion motor, zero torque is developed when brush axis coincides with the field axis and brush axis is 90° electrical to field axis.

Description : The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

Answer : Ns         equals        f/pair pole 50/4      - 12.5

Answer : The purpose of stator winding in the compensated repulsion motor is to improve power factor and provide better speed regulation.

Answer : A repulsion motor is equipped with commutator.

Description : In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

Answer : In an induction motor if the flux density is reduced.to one-half, of its normal value then the torque will reduce to one-fourth

Answer : In repulsion motor direction of rotation of motor is the same as that of brush shift.

Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Answer : For constant torque drive armature voltage control speed control method is preferred.

Description : A 3-phase, 4-pole, 50Hz induction motor runs at a speed of 1440 rpm. The rotating field produced by the rotor rotates at a speed of ________ rpm with respect to stator field. (A) 1500 (B) 0 (C) 1440 (D) 60

Answer : 0

Description : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω

Answer : In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is 0.3 Ω

Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

Answer : In case of a reluctance motor, when the load is increased so that it cannot maintain synchronous speed the motor will run as induction motor.

Answer : The speed/load characteristics of a universal motor is same as that of D.C. series motor.

Description : In a split-phase induction motor, the resistance/reactance ratios of windings are such that (A) current in the auxiliary winding leads the current in the main winding (B) current in the ... (C) both windings develop the same starting torque (D) both windings develop high starting current

Answer : In a split-phase induction motor, the resistance/reactance ratios of windings are such that current in the auxiliary winding leads the current in the main winding

Description : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

Answer : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

Answer : The speed of a D.C. shunt motor can be increased by increasing the resistance in field circuit.

Answer : As the load is increased the speed of D.C. shunt motor will reduce slightly.

Answer : The speed of a D.C. series motor is inversely proportional to the armature current.

Answer : In a D.C. shunt motor, speed is independent of armature current.

Answer : If the centrifugal switch does not open at 70 to 80 percent of synchronous speed of motor, it would result in damage to the starting winding.

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

Description : The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min (A) 100 rpm (B) 200 rpm (C) 400 rpm (D) 800 rpm

Answer : The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min 200 rpm

Answer : In variable speed motor a weaker commutating field is needed at low speed than at high speed.

Answer : Series motor has the poorest speed control.

Answer : The speed of a universal motor is usually reduced by using gearing.

Answer : Speed control of a universal motor is achieved by varying field flux with tapped field windings, connecting rheostat in series, applying variable voltage by means of silicon controlled rectifier, applying variable voltage by means of variable auto-transformer.

Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

Description : Why the speed of synchronous motor is constant?

Description : What are the speed control methods of dc motor?

Answer : Field control of DC motor Armature control of DC motor

Description : A change of 4% in the supply voltage to an induction motor will produce a change of approximately

Answer : A change of 4% in the supply voltage to an induction motor will produce a change of approximately 8% in the rotor torque

Description : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in ... increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

Answer : In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then the flux first decreases and then increases in the same direction

Answer : The rotor slots, in an induction motor, are usually not quite parallel to the shaft because it helps in reducing the tendency of the rotor teeth to remain under the stator teeth.

Answer : Torque developed by a D.C. motor depends upon magnetic field, active length of the conductor, current flow through the conductors, number of conductors, radius of armature.

Description : Split phase induction motor

Answer : Split phase induction motor : There are two windings used in split phase induction motor. It is a type of single-phase induction motor. There are two winding one is called main winding and ... motor have low starting torque it is used for small fans, blowers, centrifugal pumps, grinders etc.

Description : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 

Answer : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 4 percent

Description : A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for

Answer : A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for 4 poles

Description : An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is (A) 5.06 kW (B) 0.3 kW (C) 100 kW (D) 83.33 kW

Answer : An 8-pole, 50Hz, three-phase induction motor is running at 705rpm and has a rotor copper loss of 5kW. Its rotor input is 83.33 kW

Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Answer : If a single phase induction motor runs slower than normal, the most likely defect is worn bearings.

← Prev Question Next Question →
editChoose topic
...