1 Answer

Answer :

As hysteresis motors are free from mechanical and magnetic vibrations therefore these are considered as suitable for sound equipment.

Like 0 like

Related Questions

Description : What is magnetic hysteresis? What is the cause of hysteresis?

Last Answer : Magnetic hysteresis: When a magnetic material is subjected to cycle of magnetization, it is found that flux density (B) in the material lags behind applied magnetizing force (H). This ... the movement of orientation, due to which the flux density lags behind the magnetic field intensity.

Description : In a magnetic material hysteresis loss takes place primarily due to?

Last Answer : In a magnetic material hysteresis loss takes place primarily due to it high retentivity.

Description : Explain hysteresis loss, eddy current loss and skin effect limitations with reference to magnetic material.

Last Answer : Hysteresis loss: Hysteresis loss is a loss which occurs due to the friction of magnetic domain due to the change in magnetic field in ferromagnetic material like iron. Hysteresis loss causes power loss ... loss in transformer is given by, We=Kef2Kf2Bm2watts Skin effect limitations:

Last Answer : The rotor of a hysteresis motor is made of chrome steel.

Last Answer : In a hysteresis motor, the rotor must have retentivity.

Description : Explain the hysteresis loop of a magnetic material with neat diagram.

Last Answer : Hysteresis loop of magnetic material:  The circuit arrangement for plotting the hysteresis loop is shown in figure given below. The electromagnetic part consists of a coil wound on the iron ring ... one magnetic reversal is called hysteresis loop. Meaning of hysteresis is to lag behind.

Last Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

Description : Generally, Crawling in squirrel cage induction motors is tendency to run stably at speeds as low as (A) One-third of their synchronous speed (B) One-fifth of their synchronous speed (C) One-seventh of their synchronous speed (D) One-ninth of their synchronous speed

Last Answer : Generally, Crawling in squirrel cage induction motors is tendency to run stably at speeds as low as One-seventh of their synchronous speed

Last Answer : In D.C. shunt motors as load is reduced the speed will remain almost constant.

Description : Stepper motors are used in  (1) printers (2) lifts (3) amplifiers (4) oscillators

Last Answer : Stepper motors are used in printers 

Description : Slot harmonics are reduced in induction motors by using (A) fractional-pitch windings (B) fractional-slot windings (C) integral-slot windings (D) distributed windings

Last Answer : Slot harmonics are reduced in induction motors by using fractional-slot windings

Last Answer : When two D.C. series motors are connected in parallel, the resultant speed is normal speed.

Last Answer : Starters are used with D.C. motors because to restrict armature current as there is no back e.m.f. while starting.

Description : What are the five types of single phase motors used in the industry?

Last Answer : A direct online starter is used for starting motors up to 5 H.P.

Description : What are the factors to be considered while selection of motors for different drives?

Last Answer : Following Factors are considered while selecting electric drive (Motor) for particular application:  Factors to be considered for selection of Electrical Drives:  1) Nature of Supply:- Whether supply ... , load equalization 7) Cost: - Capital, Running and maintenance cost should be less.  

Description : Damper winding is provided in 3 phase synchronous motors to :

Last Answer : Damper winding is provided in 3 phase synchronous motors to : provide starting torque and prevent hunting

Description : Which of the following test is usually conducted to determine the efficiency of traction motors ? (A) Field’s test (B) Swinburne’s test (C) Hopkinson’s test (D) Retardation test.

Last Answer : Which of the following test is usually conducted to determine the efficiency of traction motors ? (A) Field’s test (B) Swinburne’s test (C) Hopkinson’s test (D) Retardation test.

Description : Which of the following motors is being extensively used in servo applications ? A. AC motor B. Field controlled dc motor C. Armature controlled dc motor D. None of these

Last Answer : Which of the following motors is being extensively used in servo applications ? A. AC motor B. Field controlled dc motor C. Armature controlled dc motor D. None of these

Description : In case of conductively compensated D.C. series motors, the compensating winding is provided?

Last Answer : In case of conductively compensated D.C. series motors, the compensating winding is provided in series with armature winding.

Last Answer : In case of D.C. shunt motors the speed is dependent on back e.m.f. only because flux is practically constant in D:C. shunt motors.

Last Answer : Differentially compound D.C. motors can find applications requiring low starting torque.

Last Answer : The capacitors used in single-phase capacitor motors have no polarity marking.

Last Answer : Most of the fractional horsepower motors have either plain or sleeve bearings.

Description : What is the difference between synchronous and asynchronous motors?

Last Answer : The motor which rotates at constant speed is called synchronous motor. And that constant speed is called as synchronous speed.  And the motor which does not rotates at constant speed are called asynchronous motor. Asynchronous motor is also called as Induction motor.

Description : Which of the following converts linear displacement from a mechanical reference into a proportional electrical signal containing phase and amplitude information? A) CRO B) LVDT C) RVDT D) None of these

Last Answer : Which of the following converts linear displacement from a mechanical reference into a proportional electrical signal containing phase and amplitude information? A) CRO B) LVDT C) RVDT D) None of these

Description : In a d.c. motor, the mechanical output power actually comes from?

Last Answer : In a d.c. motor, the mechanical output power actually comes from electrical input power.

Description : Explain the suitability of aluminium as an electrical conductor with respect to its mechanical and electrical properties. 

Last Answer : Following are requirements of conductor:- i) High conductivity :  Material should have high conductivity, So that * cross section of conductor (size) reduces, * Copper losses reduces, * So Efficiency ... . Boiling point is 1820°C 9. Specific gravity is 2.7 10. High resistance to corrosion. 

Description : Describe with neat sketch working of hysteresis motor.

Last Answer : Working: When stator is energized with single phase ac supply, rotating magnetic field is produced because of starting (auxiliary) and main windings, which remain in circuit permanently. The ... the principle of magnetic locking this motor either rotates at synchronous speed or not at all.

Description : State the factors affecting hysteresis loss.

Last Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

Description : Hysteresis is commonly found in ______ A) ferromagnetic materials B) ferroelectric materials C) both A and B D) none of these

Last Answer : Hysteresis is commonly found in ______ A) ferromagnetic materials B) ferroelectric materials C) both A and B D) none of these

Description : The term hysteresis is associated with (A) On-Off control (B) P-I control (C) Feed forward control (D) Ratio control

Last Answer : The term hysteresis is associated with On-Off control

Description : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

Last Answer : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be large.

Last Answer : A hysteresis motor works on the principle of hysteresis loss.

Last Answer : The direction of rotation of an hysteresis motor is determined by position of shaded pole with respect to main pole.

Description : What is the difference between eddy current and hysteresis loss?

Last Answer : Loss occurred by magnetising and demagnetising process is called histerisis loss and the current flowed due to the magnetic field produced by the electric field applied is called eddy current losses

Last Answer : In case of D.C. machines, mechanical losses are primary function of speed.

Description : Briefly explain how an electrical generator converts mechanical energy into electrical energy.

Last Answer : Working principle of DC generator: * Working principle of DC generator is the principle of dynamically induced emf or electromagnetic induction. * According to this principle, when flux is cut by a conductor, an ... , the flux is cut by the armature winding and an emf is dynamically induced in it. 

Description : Define natural, mechanical, forced and induced draught systems.

Last Answer : Natural draught system: - When the fuel is burnt (combustion) in the furnace due to natural circulation of air, the draught is called natural draught. Mechanical draught system: -  In a mechanical ... combustion. OR If fan/blower is placed after the furnace then it is called as induced draught

Description : Explain the mechanical properties of insulating materials.

Last Answer : i) Mechanical strength: Mechanical strength depends on temperature and humidity. a) Temperature: High temperature badly affects the mechanical strength of insulating material. While selecting material ... material should have property of easy moulding and machined into required shape and size.

Description : In Torque-Voltage analogy, the Moment of Inertia of a mechanical rotational system is analogous to (A) Capacitance C. (B) Inductance L. (C) Resistance R. (D) Inductive reactance XL

Last Answer : In Torque-Voltage analogy, the Moment of Inertia of a mechanical rotational system is analogous to Inductance L.

Description : The mechanical power developed by the armature of a d.c. motor is equal to?

Last Answer : The mechanical power developed by the armature of a d.c. motor is equal to armature current multiplied by back e.m.f.

Description : The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

Last Answer : The synchronous motor which works on leading power factor and does not drive any mechanical load is called synchronous condenser.

Description : State factors for selection of motors as drive.

Last Answer : Following Factors governing / or are considered while selecting electric drive (Motor) for particular application: Factors to be considered for selection of Electrical Drives: 1) Nature of Supply:- ... level, load equalization 7) Cost: - Capital, Running and maintenance cost should be less.

Last Answer : D.C. shunt motors are used for driving machine tools.

Last Answer : The D.C. motors preferred for traction applications beacuse the speed is inversely proportional to the torque and the torque is proportional to square of armature current.

Last Answer : The standard full-load power factor ratings for synchronous motors are unity or 0.8 leading.

Description : Why are DC motors used in trains and not AC motors ?

Last Answer : The reason is torque. torque is inversely proportional to speed..i.e when th knowe train comes to rest position to motion.. initial speed is zero..so it requires high starting torque for ... current will flow through field and armature coils then maximum torque is available at the intial condition.

Description : State which electric motors are generally used in electro agro systems with reason.

Last Answer : 1) 3 phase induction motor is used in electro agro system for water pumping from wells as 3 phase ac supply is easily available, cost of induction motor is less, maintenance free being rugged ... as 1 phase ac supply is easily available for domestic purpose, repair is simple and easily available.

Last Answer : Synchronous motors are generally not self-starting because the direction of instantaneous torque reverses after half cycle.

Show MoreNext Page → ← Prev Page