search
person

1 Answer

A schrage motor can run on zero slip, negative slip, positive slip.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Answer : A universal motor can run on either A.C. or D.C.

Answer : The repulsion-start induction-run motor is used because of high starting torque.

Answer : In a ceiling fan employing capacitor run motor secondary winding surrounds the primary winding.

Answer : In a capacitor start and run motors the function of the running capacitor in series with the auxiliary winding is to improve power factor.

Answer : A rotory converter can also be run as a synchronous motor.

Description : Instant 100 meters (How fast to run 100 meters?)

Answer : Instant 100 meters (How fast to run 100 meters?) This guide outlines the step-by-step preparation for the most efficient 100-meter run. 0-15 meters With your head down, you need to ... length. Constant training and the right technique will allow you to improve your 100 meter running results.

Description : Which type of heater is cheapest to run?

Answer : A shaded pole motor can be used for toys, hair dryers, circulators etc.

Answer : Direction of rotation of a split phase motor can be reversed by reversing the connection of either running winding or starting winding.

Answer : In a capacitor start motor, the phase displacement between starting and running winding can be nearly 90°.

Answer : Single phase induction motor usually operates on 0.6 power factor lagging.

Answer : The motor used on small lathes is usually single-phase capacitor run motor.

Answer : A hysteresis motor works on the principle of hysteresis loss.

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

Description : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

Answer : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be at the slot edge where coil enters or comes out of the slot.

Description : The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be?

Answer : The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be 4.

Answer : When a D.C. series motor is connected to A.C. supply, the power factor will be low because of high inductance of field and armature circuits.

Answer : The speed of a universal motor is generally reduced by using gear trains.

Answer : The wattage of motor for driving domestic sewing machine will be around 100 to 150 W.

Answer : The wattage rating for a ceiling fan motor will be in the range 50 to 150 W .

Answer : In case of a shaded pole motor the direction of rotation of the motor is from main pole to shaded pole.

Answer : In A.C. series motor compensating winding is employed to reduce sparking at the brushes.

Answer : In a two value capacitor motor, the capacitor used for running purposes is paper spaced oil filled type.

Answer : In split-phase motor auxiliary winding is of thin wire placed at the top of the slots.

Answer : A single-phase induction motor is inherently non-self-starting with low torque.

Answer : The power factor of a single-phase induction motor is usually lagging.

Answer : In a capacitor start single-phase motor, when capacitor is replaced by a resistance motor will continue to run in same direction.

Answer : The direction of rotation of an hysteresis motor is determined by position of shaded pole with respect to main pole.

Answer : In a single phase motor the centrifugal switch disconnects auxiliary winding of the motor.

Answer : In repulsion motor direction of rotation of motor is the same as that of brush shift.

Answer : The value of starting capacitor of a fractional horse power motor will be 300 uF .

Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Answer : In a shaded pole single-phase motor, the revolving field is produced by the use of shading coils.

Answer : In a shaded pole motor, the shading coil usually consist of a single turn of heavy copper wire which is short-circuited and carries only induced current.

Answer : The rotor developed by a single-phase motor at starting is zero.

Answer : In a split phase motor the starting winding is connected through a centrifugal switch.

Answer : If the capacitor of a single-phase motor is short-circuited the motor will not start.

Answer : In a split phase motor, the running winding should have low resistance and high inductance.

Description : What can cause high amperage on a motor?

Answer : High  amperage  can  result  in  a motor  when the  amount  of  load  increases. when  load  increases  , it  reduces  the  rotor  speed which  increases  the  slip  at  constant  synchronous  speed ... ,  as  a  result  more  current  shall  have  been  drawn  to  maintain  the  additional  load.

Description : The number of poles of 8/6 stepper motor can be :

Answer : The number of poles of 8/6 stepper motor can be : 4

Description : A d.c. motor can be looked upon as d.c. generator with the power flow?

Answer : A d.c. motor can be looked upon as d.c. generator with the power flow reversed.

Description : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

Answer : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

Answer : The speed of a D.C. shunt motor can be increased by increasing the resistance in field circuit.

Answer : By looking at Commutator part of the motor, it can be easily confirmed that a particular motor is D.C. motor.

Answer : The speed of a D.C. shunt motor more than its full-load speed can be obtained by decreasing the field current.

Answer : The direction of rotation of a D.C. series motor can be changed by interchanging field terminals.

Answer : The direction of rotation of universal motor can be reversed the by reversing the flow of current through either armature winding or field winding.

Answer : The operating speed of a synchronous motor can be changed to new fixed value by changing frequency.

Answer : A synchronous motor can develop synchronous torque at synchronous speed.

← Prev Question Next Question →
editChoose topic
...