In a single phase motor the centrifugal switch?

Question

asked Mar 20, 2018 by anonymous

133 views

Please log in or register to answer this question.

1 Answer

← Prev Question Next Question →

Related questions

asked Mar 20, 2018 by anonymous

A centrifugal switch is used to disconnect starting winding when motor has?

Last answer: A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

0 like 0 dislike

201 views 1 answer

asked Mar 20, 2018 by anonymous

If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then?

Last answer: If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then Electrolytic capacitor will, in all probability, suffer break down.

0 like 0 dislike

90 views 1 answer

asked Mar 20, 2018 by anonymous

Centrifugal switch disconnects the auxiliary winding of the motor at about what percent of synchronous speed?

Last answer: Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

0 like 0 dislike

141 views 1 answer

asked Mar 20, 2018 by anonymous

The running winding of a single phase motor on testing with meggar is found to be ground...

The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

Last answer: The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be at the slot edge where coil enters or comes out of the slot.

0 like 0 dislike

86 views 1 answer

asked Mar 20, 2018 by anonymous

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by...

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Last answer: A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

0 like 0 dislike

100 views 1 answer

asked Mar 20, 2018 by anonymous

Single phase induction motor usually operates on?

Last answer: Single phase induction motor usually operates on 0.6 power factor lagging.

0 like 0 dislike

98 views 1 answer

asked Sep 2, 2019 by anonymous

Why is a capacitor used in a single phase motor and not in three phase motor ?

Last answer: In 1-phase induction motor capacitor work is generate the auxiliary winding current than excite the main winding to rotor starts rotate. After rotor start rotating about 75% of their speed than auxiliary ... emf to start the motor.so,in 3-phase induction motor is self start induction motor.

0 like 0 dislike

128 views 6 answers

asked Jul 30, 2019 by anonymous

Explain the working of a single phase capacitor start induction motor.

Last answer: Single phase capacitor start induction motor https://youtu.be/31lvvzU5Puc

0 like 0 dislike

151 views 2 answers

asked Apr 29, 2018 by anonymous

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Last answer: What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

0 like 0 dislike

79 views 1 answer

asked Mar 20, 2018 by anonymous

After the starting winding of a single phase induction motor is disconnected from supply, it continues to run only on?

Last answer: Reason is kinetic energy

0 like 0 dislike

131 views 2 answers

asked Mar 20, 2018 by anonymous

If a single phase induction motor runs slower than normal, the most likely defect is?

Last answer: If a single phase induction motor runs slower than normal, the most likely defect is worn bearings.

0 like 0 dislike

109 views 1 answer

asked Mar 20, 2018 by anonymous

Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a?

Last answer: Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

0 like 0 dislike

154 views 1 answer

asked Mar 17, 2018 by anonymous

How does a single phase induction motor work?

Last answer: As we know that single phase induction is not self started because for self started we require atleast two revolving field but single phase induction motor has only one. So we provide extra ... 1phase IM classified as split phase IM, capacitor start capacitor run, capacitor start induction run.

0 like 0 dislike

92 views 1 answer

asked Oct 24, 2017 by anonymous

explain the working of single phase induction motor.

Last answer: Stator has two winding namely main winding and auxiliary winding.when single phase ac supply is given to the motor,its produces alternating field.this field cut by a cage rotor.so some emf ... due to this emf,rotor flux produced.the interaction between two fluxes produce torque.so rotor rotates.

0 like 0 dislike

106 views 1 answer

asked May 7, 2020 by anonymous

State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Last answer: Application Suitable Single Phase Motor Table Fan 1) Capacitor split phase motor 2) Capacitor start capacitor run motor Mixers and Grinders 1) Universal motor 2) A.C. Series motor

0 like 0 dislike

53 views 1 answer

asked Aug 21, 2019 by anonymous

working principle of single phase motor

Last answer: The Stator of single phase induction motor houses two windings 1. Main (Running) winding 2. Auxiliary (Starting ) winding Rotor of single phase induction motor is ... with starting winding or a capacitor may be permanently connected in series with Auxiliary (Starting ) winding.

0 like 0 dislike

94 views 1 answer

asked Mar 18, 2018 by anonymous

An unexcited single phase synchronous motor is ?

Last answer: An unexcited single-phase synchronous motor is reluctance motor.

0 like 0 dislike

86 views 1 answer

asked Aug 9, 2017 by anonymous

Single Phase Induction Motor

Last answer: Single Phase Induction Motor Single phase induction motor is mostly used in home, office, shop and many single phase appliances like pumps, ... torque and silent operation. It is uses where silent operation is required.

0 like 0 dislike

453 views 1 answer

asked Apr 28, 2018 by anonymous

A switch tail ring counter is made by using a single D-FF. The resulting circuit is

A switch tail ring counter is made by using a single D-FF. The resulting circuit is (A) T-FF (B) D-FF (C) SR-FF (D) JK-FF

Last answer: A switch tail ring counter is made by using a single D-FF. The resulting circuit is T-FF

0 like 0 dislike

70 views 1 answer

asked Mar 20, 2018 by anonymous

In a capacitor start motor, the phase displacement between starting and running winding can be nearly?

Last answer: In a capacitor start motor, the phase displacement between starting and running winding can be nearly 90°.

0 like 0 dislike

131 views 1 answer

asked Mar 20, 2018 by anonymous

In a split phase motor, the running winding should have?

Last answer: In a split phase motor, the running winding should have low resistance and high inductance.

0 like 0 dislike

69 views 1 answer

asked Mar 20, 2018 by anonymous

In a split phase motor?

Last answer: In a split phase motor the starting winding is connected through a centrifugal switch.

0 like 0 dislike

49 views 1 answer

asked Aug 13, 2019 by Alacrity

the volt per turn of a certain single phase transformers is 1.7. the transformer has a step ratio of 3825/255volt. calculate the respective number of turns in each winding

0 like 0 dislike

49 views 0 answers

asked Apr 25, 2018 by anonymous

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

Last answer: The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is 500 W

0 like 0 dislike

140 views 1 answer

asked Mar 21, 2018 by anonymous

In a single phase power factor meter the phase difference between the currents in the two pressure coils is?

Last answer: In a single phase power factor meter the phase difference between the currents in the two pressure coils is exactly 90°.

0 like 0 dislike

160 views 1 answer

asked Mar 20, 2018 by anonymous

Direction of rotation of a split phase motor can be reversed by reversing the connection of?

Last answer: Direction of rotation of a split phase motor can be reversed by reversing the connection of either running winding or starting winding.

0 like 0 dislike

146 views 1 answer

asked Mar 15, 2018 by anonymous

What are the five types of single phase motors used in the industry?

0 like 0 dislike

66 views 0 answers

asked Mar 21, 2018 by anonymous

Induction type single phase energy meters measure electric energy in?

Last answer: Induction type single phase energy meters measure electric energy in kWh.

0 like 0 dislike

241 views 1 answer

asked Mar 11, 2018 by anonymous

Explain power in single phase AC circuit.

0 like 0 dislike

68 views 0 answers

asked Jul 25, 2019 by anonymous

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last answer: Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

0 like 0 dislike

164 views 1 answer

asked Apr 29, 2018 by anonymous

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last answer: What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

0 like 0 dislike

136 views 1 answer

asked Apr 28, 2018 by anonymous

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last answer: A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

0 like 0 dislike

693 views 1 answer

asked Apr 25, 2018 by anonymous

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last answer: The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

0 like 0 dislike

266 views 1 answer

asked Mar 21, 2018 by anonymous

The power factor of a single phase load can be calculated if the instruments available are?

Last answer: The power factor of a single phase load can be calculated if the instruments available are three ammeters or three voltmeters.

0 like 0 dislike

136 views 2 answers

asked Mar 21, 2018 by anonymous

The two pressure coils of a single phase power factor meter have?

Last answer: The two pressure coils of a single phase power factor meter have the same dimensions and the same number of turns.

0 like 0 dislike

74 views 1 answer

asked Mar 11, 2018 by anonymous

Describe the gate circuit for a single phase full converter.

0 like 0 dislike

60 views 0 answers

asked May 3, 2018 by anonymous

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Last answer: A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

0 like 0 dislike

232 views 1 answer

asked Apr 27, 2020 by anonymous

Explain the procedure to perform Short Circuit test on single phase transformer with circuit diagram.

0 like 0 dislike

69 views 0 answers

asked Mar 19, 2018 by anonymous

For the parallel operation of single phase transformers it is necessary that they should have?

Last answer: Necessary conditions required to be satisfied in order to ensure successful parallel operation of single phase transformers: 1. Only transformers having the same phase displacement between primary and secondary ... . 7. The phase sequence must be followed strictly on HV and LV side connection.

0 like 0 dislike

112 views 2 answers

asked May 21, 2020 by anonymous

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Last answer: Circuit Diagram: Waveforms:

0 like 0 dislike

202 views 1 answer

asked May 16, 2020 by anonymous

Single phase transformer

Last answer: Single phase Transformer Transformer

0 like 0 dislike

234 views 1 answer

asked May 7, 2020 by anonymous

Explain MCB and ELCB with connection diagram supplying single phase load.

Last answer: OR OR Explanation: * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with ... occurs, the ELCB cuts off the power within the time of 0.1 sec. automatically to protect the personnel.

0 like 0 dislike

210 views 1 answer

asked Jul 26, 2019 by anonymous

Explain construction and working principle of single phase transformer.

Last answer: A single phase transformers is an electrical device that accepts single-phase AC power and outputs single-phase AC. PRINCIPLE... The single-phase transformer works on the principle of ... and secondary windings. Thin steel laminations shall be employed to prevent power losses from the core.

0 like 0 dislike

346 views 4 answers

asked Aug 11, 2018 by anonymous

State advantages of three phase over single phase.

Last answer: Advantages of 3-phase system over 1-phase system: - 1. More output: For the same size, output of poly-phase machines is always higher than single phase machines. 2. Smaller size: For ... are self- starting: The three phase ac motors are self starting, while single phase induction motor are not.

0 like 0 dislike

2.8k views 4 answers

asked Dec 12, 2017 by anonymous

write short notes on single phase system.

Last answer: A "phase" in an electrical system is often referred to as the waveform (may be voltage or the current) of the power supply. The waveform in an AC system is typically ... domestic household or commercial supplies and street lighting. Industrial supplies requires three phase electrical supply .

2 like 0 dislike

83 views 1 answer

asked Nov 16, 2017 by anonymous

three phase to single phase cycloconverter

Last answer: three phase to single phase cycloconverter

1 like 0 dislike

403 views 1 answer

asked Nov 16, 2017 by anonymous

single phase full converter

Last answer: single phase full converter

1 like 0 dislike

85 views 1 answer

asked Mar 20, 2018 by anonymous

In case one phase of a three-phase synchronous motor is short-circuited the motor will?

Last answer: In case one phase of a three-phase synchronous motor is short-circuited the motor will not start.

0 like 0 dislike

178 views 1 answer

asked Mar 20, 2018 by anonymous

In a shaded pole single-phase motor, the revolving field is produced by the use of?

Last answer: In a shaded pole single-phase motor, the revolving field is produced by the use of shading coils.

0 like 0 dislike

86 views 1 answer

asked Mar 20, 2018 by anonymous

In a capacitor start single-phase motor, when capacitor is replaced by a resistance?

Last answer: In a capacitor start single-phase motor, when capacitor is replaced by a resistance motor will continue to run in same direction.

0 like 0 dislike

82 views 1 answer

anonymous · Answer 1 · 2018-03-20T18:58:59+0000

In a single phase motor the centrifugal switch disconnects auxiliary winding of the motor.

In a single phase motor the centrifugal switch?

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions