search
person

1 Answer

Generating capacity connected to the bus bars and ready to take load when switched on is known as spinning reserve.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : In a lamp load when more than one lamp are switched on the total resistance of the load?

Answer : In a lamp load when more than one lamp are switched on the total resistance of the load decreases.

Description : In load flow Study, a PV bus is treated as a PQ bus when

Answer : Voltage at the bus becomes high 

Description : Sparking occurs when a load is switched off because the circuit has high?

Answer : Sparking occurs when a load is switched off because the circuit has high inductance.

Description : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

Answer : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is 122.8 GWh

Description : The problematic pollutants in emission of coal based generating plants __________.  (A) SO₂ (B) NOx (C) CO (D) All of the above

Answer : The problematic pollutants in emission of coal based generating plants __________.  (A) SO₂ (B) NOx (C) CO (D) All of the above

Answer : In a power plant if the maximum demand on the plant is equal to the plant capacity, then plant reserve capacity will be zero.

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

Description : If a transformer is switched on to a voltage more than the rated voltage?

Answer : If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Answer : Large capacity generators are invariably hydrogen cooled.

Answer : Power plant having maximum demand more than the installed rated capacity will have utilisation factor more than unity.

Description : A Hartley Oscillator is used for generating (A) very low frequency Oscillation (B) radio-frequency Oscillation (C) microwave Oscillation (D) audio-frequency Oscillation

Answer : A Hartley Oscillator is used for generating radio-frequency Oscillation

Description : Thyristor Switched Capacitor (TSC)

Answer : Thyristor Switched Capacitor (TSC)  TSC is a static compensator. TSC is use for compensating reactive power. Compensation is required for voltage regulation, increasing stability, ... compensating device like TCS phase angle between voltage and current can be maintain.

Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Description : Calculate the size of memory address space for a 16 bit data and 20 bit address bus. A) 1 MB B) 2 MB C) 3 MB D) 4 MB

Answer : Calculate the size of memory address space for a 16 bit data and 20 bit address bus. A) 1 MB B) 2 MB C) 3 MB D) 4 MB

Description : What are the components of system bus? A) CPU Bus, Address Bus, Data Bus B) Memory, Control Unit, ALU C) Data Bus, Address Bus, Control Bus D) Register, PC, IR

Answer : What are the components of system bus? A) CPU Bus, Address Bus, Data Bus B) Memory, Control Unit, ALU C) Data Bus, Address Bus, Control Bus D) Register, PC, IR

Description : Which of the following is true for a bus impedance matrix ?  (A) It is sparse  (B) It has diagonally dominant elements  (C) It is the inverse of the bus admittance matrix  (D) Each element of it is the reciprocal of the corresponding element in admittance matrix

Answer : Which of the following is true for a bus impedance matrix ?  (A) It is sparse  (B) It has diagonally dominant elements  (C) It is the inverse of the bus admittance matrix  (D) Each element of it is the reciprocal of the corresponding element in admittance matrix

Description : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

Answer : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by ( ... /notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

Answer : Nuclear power plant is invariably used as base load plant.

Answer : Load factor of a power station is defined as average load/maximum demand.

Answer : Overload capacity of diesel engines is usually restricted to 2 percent.

Description : What is the channel capacity of a noisy channel with conditional probability of error p = 1/2? A) 0 B) 1 C) Infinity D) 2  

Answer : What is the channel capacity of a noisy channel with conditional probability of error p = 1/2?  A) 0 B) 1 C) Infinity D) 2  

Description : Breaking capacity of a circuit breaker is usually expressed in terms of  (1) Ampere (2) Volts (3) MW (4) MVA

Answer : Breaking capacity of a circuit breaker is usually expressed in terms of MVA

Description : In order to have a lower cost of electrical energy generation the load factor  (1) and the diversity factor should be low (2) should be low but the diversity factor should be high (3) should be high but the diversity factor should be low (4) and the diversity factor both should be high

Answer : In order to have a lower cost of electrical energy generation the load factor and the diversity factor both should be high

Answer : The increased load during summer months is due to increased use of fans and air conditioners.

Description : Compare base load plant with peak load plant. 

Answer : Sr.No. Points Base load plant Peak load plant  1 Definition The power plant which supplies base load of load curve is known as base load plant The power ... power station   Small capacity storage hydro, pumped storage hydro, gas, diesel power station. 

Answer : Generators for peak load plants are usually designed for maximum efficiency at 50 to 75 percent full load.

Answer : In a load curve the highest point represents peak demand.

Answer : Load curve is useful in deciding the operating schedule of generating units, sizes of generating units, total installed capacity of the plant.

Answer : The area under a load curve gives energy consumed.

Answer : Peak load plant can never have 100 percent load factor.

Answer : In two part tariff, variation in load factor will affect operating or running charges.

Answer : A load curve indicates average kWh (kW) energy consumption during the period.

Answer : High load factor indicates total plant capacity is utilised for most of the time.

Answer : The load factor of domestic load is usually 10 to 15%.

Answer : Load factor of a power station is generally less than unity.

Description : Define the following terms related to tariff: (i) Connected load (ii) Unit consumed (iii) Fixed charges (iv) Electricity Tax 

Answer : (i) Connected load  It is the sum of the power ratings (Watts or kW or MW) of all devices and machines existing (installed) in the premises of consumer. It is used to decide the ... a percentage of the total electricity bill which includes all amounts that go to the electricity supply agency. 

Description : The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Answer : The sequence components of current of a single-phase load connected to a 3-phase system are equal positive, negative and zero sequence components

Description : A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

Answer : Series capacitors on transmission lines are of little use when the load VAR requirement is small.

Description : Define the terms: i) Tariff ii) Fuel surcharge iii) Electricity Duty iv) Connected load

Answer : i) Tariff: The rate at which a consumer is charged for the consumption of electricity is called as tariff. OR The amount of money framed by the supplier for the supply of electrical energy ... is the total wattage of all appliances which are used by the consumer on his sanctioned connection. 

Description : Define each of following terms: i) Connected load ii) Spinning reserve. 

Answer : i) Connected Load :- It is the sum of load of all equipment connected to supply system which are in use or not in use of each consumer. ii) Spinning Reserve:- It is reserved generating capacity in operation and connected to bus bar and ready to take a load.

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Description : A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

Answer : Leading

Description : Minimum voltage regulation occurs when the power factor of the load is?

Answer : Minimum voltage regulation occurs when the power factor of the load is leading.

Description : The synchronous motor will develop maximum power when the load angle is?

Answer : The synchronous motor will develop maximum power when the load angle is 900.

Description : Explain with neat circuit diagrams the procedures to perform no load and blocked rotor tests on three phase induction motor.

Answer : If the synchronous motor, properly synchronised to the supply is running on no load and is having negligible loss then the stator current will be zero.

Description : State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant. 

Answer : 1. Because of following points Nuclear power plant used as base load power plant:-  1. Nuclear power plants is very economical for producing bulk amount of electric power 2. Nuclear power plant is reliable ... . The plants can be put on load easily. 4. Diesel engines take less time to make OFF.

Description : The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

Answer : The synchronous motor which works on leading power factor and does not drive any mechanical load is called synchronous condenser.

← Prev Question Next Question →
editChoose topic
...