search
person

1 Answer

Annual depreciation as per straight line method, is calculated by the capital cost minus the salvage value, is divided by the number of years of life.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Answer : Depreciation charges are high in case of thermal plant.

Answer : Annual operating expenditure of a power plant consists of fixed charges, semi-fixed charges, running charges.

Answer : The power factor of a single phase load can be calculated if the instruments available are three ammeters or three voltmeters.

Description : For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

Answer : For 11kV line the inductance per km per phase will be of the order of: 1 mH

Description : While calculating performance of medium transmission line, what assumptions are made in case of (i) Nominal 'T' Method (ii) Nominal 'TT' Method. 

Answer : (i) Assumptions are made in case of Nominal 'T' Method:  a. It is assume that line capacitance is connected at center of transmission line. b. It is assume that half ... assumed that transmission line resistance & reactance per phase is connected in between two half transmission line capacitance 

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Description : Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Answer : Energy conservation techniques by installation of separate transformer / servo stabilizer: The luminous efficiency of lamps depends upon the voltage applied across the terminals. It gives its best ... the voltage constant in that installation for giving best luminous efficiency of lamps.

Description : With neat diagram explain calibration of energy meter by direct loading method.

Answer : Calibration of Energy Meter by Direct Loading Method:  There are three methods for testing/calibration:  1. Long period dial test  2. Using rotary sub- standard meter  3. Using precision grade instruments  All ... of substandard meter in kWh  Then % error = [(D - DS)/DS] x 100

Description : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

Answer : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is between 0.5 and unity

Answer : Speed control by Ward Leonard method gives uniform speed variation in both directions.

Description : The surge impedance for over head line is taken as  (1) 10-20 ohms (2) 50-60 ohms (3) 100-200 ohms (4) 1000-2000 ohms

Answer : The surge impedance for over head line is taken as 100-200 ohms

Description : For a 500 Hz frequency excitation, a 50 km long power line will be modeled as

Answer : For a 500 Hz frequency excitation, a 50 km long power line will be modeled as long line

Answer : In main line service as compared to urban and suburban service distance between the stops is more, maximum speed reached is high, acceleration and retardation rates are low.

Description : Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Answer : Types of Triggering: 1) Forward voltage triggering 2) Thermal triggering (Temperature triggering) 3) Radiation triggering (Light triggering) 4) dv/dt triggering 5) Gate triggering ... generated leakage current increases. This current gets multiplied internally and thyristor is turned on. 

Description : Draw and explain vacuum impregnation method of varnishing.

Description : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Answer : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Description : Describe fire extinguishing method.

Answer : (i) Carbon Dioxide Extinguishing Systems  This type is the most suitable & widely recommended one for electrical fires. Carbon dioxide (CO2) extinguishers are normally Class C ... particles to expand chemically inhibiting combustion and expelling the oxygen thereby smothering the flames.

Description : Draw and explain bulk correction method for power factor & control.

Answer : Bulk correction method for power factor & control: i) Here individual starter controls the capacitors located at distribution panel. ii) Centralized compensation is employed in large industrial plants where many ... capacitor units in steps to maintain P.F. more than preset limit (0.95). 

Description : Merits of two wattmeter method

Answer : Advantages of Two Wattmeter Method for 3-Phase Power Measurement: 1) It is used for balanced as well as unbalanced load. 2) For the star type load, it is not necessary to ... reactive volt-amperes for balanced loads also. 7) The circuit connections are independent of load connection.

Description : Write one advantage and one disadvantage each for spring control method and gravity control method.

Answer : Advantages of Spring Control Method: 1) The spring-controlled meters may be used in any position. 2) In some instruments, springs can be used as current leads. 3) As springs are light in weight ... only. 2) Scale is non-uniform. 3) Control weights add to the weight of instrument.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

Description : Explain V- I method of measurement of medium resistance. 

Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

Description : Explain spring control method with neat diagram.

Answer : Spring Control Method: As shown in the figure the inner ends of the both springs are attahced to the spindle ,while outer end of upper spring is attached to the lever and outer end of ... the springs are twisted in opposite direction to the motion of pointer and produce controlling torque.

Description : List one advantage and one disadvantage of one wattmeter method. 

Answer : Advantages:  1) Only one wattmeter is used.  2) Less number of connections.  3) Cost required is less.  Disadvantages:  1) Used only for 3- Φ balanced load and not for ... be accessible for connecting the Pressure coil.  3) Delta connection must be opened to connect current coil. 

Description : List any four errors in induction type energy meter. Give method of compensation for each.

Answer : Errors in Induction Type Energy Meter with their Compensation:  1) Error due to friction: This error can be compensated by the additional shading band provided on the shunt electromagnet.  2) Phase ... error: This error can be compensated by providing a flux diverter' to the current magnet. 

Description : The self GMD method is used to evaluate

Answer : The self GMD method is used to evaluate inductance and capacitance

Description : Compared to Gauss-Seidel method, Newton-Raphson method takes : A. less number of iterations and more time per iteration B. less number of iterations and less time per iteration C, more number of iterations and more time per iteration D. more number of iterations and less time per iteration

Answer : Compared to Gauss-Seidel method, Newton-Raphson method takes : A. less number of iterations and more time per iteration B. less number of iterations and less time per iteration ... of iterations and more time per iteration D. more number of iterations and less time per iteration

Description : The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Answer : The bridge method commonly used for finding mutual inductance is Heaviside Campbell bridge

Answer : Plugging braking method can bring the locomotive to dead stop.

Answer : Plugging method of braking is generally used in elevators.

Answer : Regenerative method of braking is based on that back e.m.f. is equal to the applied voltage.

Answer : The main disadvantage of the Ward-Leonard control method is high initial cost, high maintenance cost, low efficiency at light loads.

Answer : For constant torque drive armature voltage control speed control method is preferred.

Description : What is the bisection method?

Description : Why do we use Gauss elimination method?

Description : What is Newton Raphson Method example?

Description : Stability of a transmission line can be increased by

Answer : Stability of a transmission line can be increased by Shunt capacitor, Series capacitor

Description : The sag of a transmission line is least affected by (A) Self weight of the conductor. (B) Temperature of the surrounding air. (C) Current through the conductor. (D) Ice deposited on the conductor.

Answer : The sag of a transmission line is least affected by Current through the conductor.

Answer : The inductive interference between power and communication line can be minimized by transposition of the power line, transposition of the communication line.

Answer : The interaction between a transmission line and communication line is minimized by transposing transmission as well as communication lines, increasing the height of the transmission line tower, increasing the distance between the two lines.

Answer : A transmission line is protected by distance protection, time graded and current graded overcurrent protection.

Description : what is mean by medium transmission line ?

Answer : The transmission line which have length between 80 km to 250 km is known as medium transmission line.

Description : what is mean by short transmission line ?

Answer : The transmission lines which have length less than 80 km is known as short transmission lines.

Description : what is mean by long transmission line ?

Answer : The transmission line which have length more than 250 km are known as long transmission lines.

Description : State the limitations of EHVAC transmission line. 

Answer : Following are the Limitations of EHVAC Transmission:   1. Insulation cost increases as voltage increases 2. Skin effect is more 3. Proximity effect is more. 4. Corona loss increases. 5. Radio ... 18. EHVAC is economical only for bulk amount of power is to be transmitted over long distance. 

Description : List the properties of line insulators in brief

Answer : Following are the properties of line insulators:  A) Electrical Properties of insulating material:- 1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high ... of insulating material:- 1. It should have longer life. 2. It should have low cost

Description : State line parameters of transmission line. 

Answer : Following are the of Line parameters of transmission line:  1. Resistance  2. Inductance  3. Capacitance

Description : State the meaning of Single line diagram.

Answer : Meaning of Single line diagram: The single line diagram of a power system is the network which shows the main connections and arrangement of the system components along with their data ( ... breakers, transformers, capacitors, bus bars, and conductors are shown by standardized schematic symbols. 

Description : State the impact of inductance and resistance on transmission line performance

Answer : Impact of inductance on transmission line: 1) It causes IXL drop in transmission line which affects regulation. 2) It is the only parameter which decides power transmission capacity of line i. ... is very small, it causes losses, temperature rise& poor voltage regulation so it cannot be neglected

← Prev Question Next Question →
editChoose topic
...