search
person

1 Answer

The underground system cannot be operated above 66 kV.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Draw and explain the construction of underground cables. 

Answer : Underground cables:   OR Explanation:- i) Core or conductor: * It function is carry current. * Cable may have single or more than single core conductor. * Conductor ... handling of cables. * It is similar to bedding & consists of fiborous material such as jute. 

Description : Differentiate between overhead transmission and underground transmission.

Answer : Points Overhead line  Underground cable Capital cost  Less More Erecting cost  Less More Time require for completion of work Less More Flexibility More ... Space consumed Space consumed  No space consumed Appearance Not good  Very good 

Description : State the procedure for laying / installation of underground cable.  

Answer : 1) Direct laying Cable: or Trench laying method: Procedure: * For laying of a cable trench about 1.5m deep and 0.5m wide is made along the cable route. * A ... over. * Cables laid in this manner are usually plain lead covered because troughing affords good mechanical protection. 

Description : Why don't we burry power lines underground ?

Answer : Because conductor used for power transmission are not insulated and if we do so it create phase to ground fault causing interruptions to supply.

Description : Why underground service connections are service connections are costly than overhead service connection

Answer : Reason: Underground service connection is given by underground cable. This cable is costly than bare conductor. Sometimes cable trench is required for cable laying, which requires additional cost. So underground service connections are costly than overhead service connection.

Description : what is the use of bedding on underground cable?

Answer : Bedding is the layer above the lead sheath it protects the lead sheath from corrosion that means it gives chemical protection to metallic sheath(lead sheath)

Description : Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Answer : Thyristor operated dimmer: A popular thyristor operated dimmer circuit employ TRIAC-DIAC phase control for low AC power control. During each half-cycle, the capacitor charges through (R1+VR1). When the ... time constant {C (R1+VR1)}. Thus by reducing VR1 the lamp brightness can be increased.

Description : Why CT is never operated with an open secondary ?

Answer : CT secondary should never be kept open because it will cause saturation of the core to a high level and very high voltage will appear across the secondary which can breakdown the insulation. One terminal of PT secondary is always grounded to avoid capacitive induction and for human safety

Description : The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min (A) 100 rpm (B) 200 rpm (C) 400 rpm (D) 800 rpm

Answer : The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min 200 rpm

Answer : Battery operated trucks are used in factories for material transportation.

Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

Answer : Induction cup relay is operated due to changes in current, voltage, impedance.

Description : If a transformer is continuously operated the maximum temperature rise will occur in?

Answer : If a transformer is continuously operated the maximum temperature rise will occur in windings.

Answer : Overhead system can be designed for operation up to 400 kV.

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Description : How can the steady-state error in a system be reduced?  (1) By decreasing the type of system (2) By increasing system gain (3) By decreasing the static error constant (4) By increasing the input

Answer : How can the steady-state error in a system be reduced?  (1) By decreasing the type of system (2) By increasing system gain (3) By decreasing the static error constant (4) By increasing the input

Description : A second order system shows 100% overshoot in its unit step response. It can be categorized as (A) underdamped system. (B) overdamped system. (C) Critically damped system. (D) undamped system.

Answer : A second order system shows 100% overshoot in its unit step response. It can be categorized as undamped system.

Description : lf the poles of system are lying on the imaginary axis in s-plane, then the system will be

Answer : lf the poles of system are lying on the imaginary axis in s-plane, then the system will be marginally stable

Description : The damping factor of a particular system is unity, the system response will be

Answer : The damping factor of a particular system is unity, the system response will be critically damped

Description : The steady state error of the system can be minimized by

Answer : The steady state error of the system can be minimized by increasing gain k

Answer : In a single bus-bar system there will be complete shut down when fault occurs on the bus itself.

Answer : The steady state stability of the power system can be increased by connecting lines in parallel.

Description : Two 3-phase transformers cannot be operated in parallel, if their :  (A) kVAs are different (B) phase sequences are different (C) % impedances are different (D) voltage ratios are different

Answer : Two 3-phase transformers cannot be operated in parallel, if their : phase sequences are different

Description : SOLAR SYSTEM FACTS

Answer : There are tons of asteroids in our solar system. One of them, Asteroid 243 Ida, even has it's own moon. One of the moons of Saturn, called Mimas, is heavily cratered. This creates an odd appearance ... our solar system, the sun still accounts for 99.8 percent of the total mass of our solar system.

Description : Draw a neat sketch of Gating system. State the functions of any four elements.  

Answer : Gating system:  1. Sprue: The circular cross section that minimizes heat loss and turbulence is sprue, and the area of it is quantified from the choke area as well as the gating ratio.  2. ... the molten metal flow from the ingate has to be proportional to the casting area's volume. 

Description : Designate a tool 8 – 10 – 6 – 6 – 5 – 10 – 0.8 signature in ASA system.  

Answer : 1. Back rake angle-8 2. Side rake angle-10. 3. End relief angle-6. 4. Side relief angle-6 5. End cutting edge angle-5 6. Side cutting edge angle-10. 7. Nose radius-0.8 mm.

Description : Draw the labeled block diagram of process control system and explain each block.

Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

Description : Grid distribution system

Answer : Grid distribution system:-  In this system, when the feeder or loop or ring is charged (energized) by two or more than two substations from two or more than two different generating stations then it is known as “Grid distribution system. In this system only one feeder is utilized at a time. 

Description : Define: primary and secondary distribution system 

Answer : i) Primary Distribution:  It is a 3-phase, 3-wire transmission line connected in between receiving substation to Distribution substation. OR It is link between receiving substation & ... substation to consumer line. OR It is link between distribution transformer substation & consumer. 

Description : List classification of distributor system with their advantages each.

Answer : According to scheme of connection there are three types of distribution systems: - 1.Radial (Tree) distribution system 2.Ring mains (Loop) distribution system 3. Grid (interconnected) ... It has highest reliability to maintain supply even when there was maintenance on any one feeder.

Description : State advantages and disadvantages of radial distributor system. 

Answer : Advantages of radial distributor system: 1. Design of layout is simple. 2. Capital cost & Erecting cost is less as there is only one feeder. 3. Time required for completion of ... maintain supply to consumers when there is maintenance on feeder. 3. Voltage fluctuations are more.

Description : Summerise the role of power system engineer.

Answer : Role of power system engineer:  i. On the planning side he or she has to make decisions on how much electricity to generate  ii. For operation of the power system he has to plan for ... for energy conservation and load management. viii. For solving the power system problems he has to update with

Description : State the losses in secondary distribution system. 

Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

Description : With neat circuit diagram explain working of emergency light system. 

Answer : Emergency lighting system:  In the residential, commercial and industrial areas, the illumination system work with available AC supply. In the event of AC supply failure, partial illumination can be ... glows. In rthis way, on failure of AC supply, light is obtained from DC supply.

Description : characteristics of Hi-Fi amplifier system.

Answer : Characteristics of HI-FI amplifier: 1. Signal to noise ratio should be better than 50dB. 2. Frequency response should be flat within +-1dB. 3. Nonlinear distortion should not be more ... provided. 6. Environmental conditions should be such as to eliminate the external noise in listening room. 

Description : DTH System

Answer : Outdoor unit: It consists of a receiving antenna, low noise amplifier & converter the receiving antenna is parabolic reflector with a horn as the active element. The horn can be ... fed to the normal domestic TV receiver, which after due processing reproduces picture & sound. 

Description : Describe the function of MUSE system for HDTV.

Answer : Bandwidth can be reduced by MUSE (Multiple Sub -Nyquist Sampling Encoding) system MUSE stands for Multiple Sub-Nyquist sampling encoding and is an HDTV bandwidth compression schemedeveloped by ... digital Audio system is called DANCE (Digital Audio Near-Instantaneous Compression and expansion). 

Description : requirements of a distribution system

Answer : Following requirements of a distribution system.  1. Layout should be simple in design. 2. It should have less initial cost 3. The distribution system should have minimum distribution ... stability of existing distribution system. 15. Time required for completion of work should be less. 

Description : Why radial distribution system used for short distance ? 

Answer : Because of following disadvantages radial distribution system is not used for long distance:  Since there is only one feeder to DTC feed at one point so, 1) There is no reliability ... more time for fault finding & repairing Hence radial distribution system is used for short distance.

Description : vertical deflection system and explain its operation.

Answer : The main function of the vertical deflection system , is to provide an amplified signal of proper level to derive the vertical deflection plates without any distortion. For amplification of the ... suppression, reduced nonlinear effects because none of the plates are at ground potential.

Description : Working of Simple Vapor absorption system

Answer : Working of Simple Vapor absorption system:  A Simple Vapor absorption system consists of evaporator, absorber, generator, condenser, expansion valve, pump & reducing valve. In this system ammonia ... where there is scarcity of Electricity and it is very useful at partial and full load. 

Description : Draw block diagram of CNC system and state function of each block.

Answer : (i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic ... Unit: A monitor is used to display the programs, commands and other useful data of CNC machine. 

Description : Write four advantages of FMS (Flexible Manufacturing System).

Answer : 1. Large variety of same products 2. Profitable investment. 3. Requires limited inventory. 4. Low labor cost. 5. Flexible system. 6. Speedy production. 7. Improve product quality. 

Description : List and explain the components of a hydraulic system.

Answer : Components Hydraulic: Hydraulic pump- Supply fluid to the components in the system. Pressure in the system develops in reaction to the load. Hence, a pump rated for 5,000 ... mechanical components and need to be removed along with other contaminants.  Seals, fittings and connections.

Description : Explain how MEMS accelerometer is used as airbag sensor for car system.

Answer : MEMS Accelerometer is used as airbag sensor: Mechanical ignition airbags fit inside the steering wheel pad. When a collision occurs, the inertial sensor moves, setting off a ... the airbag with wiring. This is especially effective when fitting both driver- and passenger-side airbags.

Description : What are advantages and disadvantages of Mechatronics system? 

Answer : Advantages of Mechatronics system:  High level of integration.  Increased functionality and better design.  More use of electronics and software instead of mechanical function.  Assumes ... Its replacement is difficult, that it is difficult to change old system to new system. 

Description : Explain in brief how anti-lock braking system works

Answer : An ABS is a system on motor vehicles which prevents the wheels from locking while braking stopping safely is one of the most important functions a motor vehicle can perform. Diagram: ... to decrease the pressure on the braking circuit, effectively reducing the braking force on that wheel.

Description : Differentiate between pneumatic and hydraulic system. 

Answer : Pneumatic System Hydraulic System 1 Pneumatic system uses gas for power transmission, after compression and it is used as medium for carrying out mechanical work. ... : In industrial applications, air conditioners Applications: In petrochemical industries, oil refineries.

Description : Explain the Mechatronics system with the help of block diagram and labeled the various elements. 

Answer : The key elements of Mechatronics systems can be classified under following categories:  Information systems  Mechanical systems  Electrical systems  Computer systems  Sensor and actuators  ... is adjusted based on generated error and again signal is given to actuators and sensors.

Description : Describe the procedure for working of paging system.

Answer : Pager is a Simplex Communication Device. Paging Systems are communication systems that send messages to a subscriber. Message can be numeric or alphanumeric. Paging Systems are used to notify a subscriber ... message is sent by sender to his pager and the message will be displayed in the LCD.

← Prev Question Next Question →
editChoose topic
...