1 Answer

A switchgear is device used for switching, controlling and protecting the electrical circuit and equipment.

Like 0 like Dislike 0 dislike

Related questions

Description : Which of the following device is used for coupling microwave energy?  A) Resonator B) Waveguide C) Loop D) Antenna

Answer : Which of the following device is used for coupling microwave energy?  A) Resonator B) Waveguide C) Loop D) Antenna 

Answer : Wagner earthing device is used to eliminate errors due to electrostatic coupling.

Description :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

Answer :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

Answer : Basically a potentiometer is a device for comparing two voltages.

Description : State any four materials used in fabrication of semiconductor device and describe its need.

Answer : For fabrication of semiconductor devices like transistors diode, solar cell etc. we have to make use of following types of materials  1. Substrate: o It is used for deposition of thin ... . o Metal cans and sealed glass containers satisfy the extreme requirements of space and military users.

Description : Linear and non-linear device

Answer : Linear and non-linear device

Description : Why transistor is called as bipolar device.

Answer : BJT is called bipolar device because in BJT current conduction takes place due to majority as well as minority charge carriers that is because of electrons as well as holes.

Description : The device which allows reverse power flow and withstands highest switch frequency is (A) GTO (B) MOSFET (C) IGBT (D) Inverter grade SCR

Answer : The device which allows reverse power flow and withstands highest switch frequency is MOSFET

Description : A snubber circuit is connected to the power semiconductor device to reduce the (A) turn-on time (B) turn-off time (C) electrical stresses (D) thermal resistance

Answer : A snubber circuit is connected to the power semiconductor device to reduce the electrical stresses

Answer : A damping device prevents the oscillation of the moving system and enables the latter to reach its final position quickly.

Description : Is FPGA a volatile device?

Answer : Yes, FPGA is a volatile device.

Description : What is an example of an analog device?

Answer : No, IGBT is not the current controlled device. IGBT is a voltage controlled device. IGBT have combine qualities of MOSFET and BJT. The high switching speed of MOSFET and low conduction losses of BJT. Also, IGBT which stands for Insulated Gate Bipolar Transistor have high input impedance.

Answer : Thyristor can only be turned on by small gate pulse but it cannot be turn off by using gate hence thyristor is called semi controlled device.

Answer : Thyristor can be turn on by positive gate pulse and the current will continue to flow through the device even when the gate voltage is low hence thyristor is called latching device.

Answer : No, BJT is a current controlled device .

Answer : already answered here is mosfet current controlled device?

Description : A relay used for protection of motors against overload is :  (A) Impedance relay (B) Electromagnetic attraction type (C) Thermal relay (D) Buchholz's relay

Answer : A relay used for protection of motors against overload is : Thermal relay

Description : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Answer : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Description : A negative sequence relay is used for protection of  (1) Generator (3) Motor (2) Transformer (4) Long Transmission lines

Answer : A negative sequence relay is used for protection of Generator 

Description : Regulating-transformers are used in power systems for control of

Answer : Regulating-transformers are used in power systems for control of power flow

Description : Surge absorbers are used for protection against

Answer : Surge absorbers are used for protection against low voltage high frequency oscillations

Answer : The material used for fuse must have low melting point and high specific resistance.

Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

Answer : The single phasing relays are used for the protection of three phase motors.

Answer : The under voltage relay can be used for generators, busbars, transformers, motors.

Answer : Impedance relays are used for phase faults on long line.

Answer : Air blast circuit breaker is used for repeated duty.

Description : Light triggering is mainly used in

Answer : Light triggering is mainly used in High voltage direct current transmission

Description : Auto reclosing is used in case of

Answer : Auto reclosing is used in case of air blast C.B.

Description : The material used in liquid fuses is  (1) SF6 (3) carbon tetra chloride (2) distilled water (4) transformer oil

Answer : The material used in liquid fuses is  carbon tetra chloride

Description : IDMT relays are used to protect the transformer against :  (A) Internal short -circuits (B) Open circuits (C) External short circuits (D) Oil leakage

Answer : IDMT relays are used to protect the transformer against : External short circuits

Description : Series reactors are used to

Answer : Series reactors are used to bring down the fault level within the capacity of the switchgear

Description : ln a minimum oil circuit breaker the oil is used

Answer : ln a minimum oil circuit breaker the oil is used to act as circuit breaking medium only

Answer : Series capacitors are used to compensate for line inductive reactance.

Answer : A.C. network analyser is used to solve problems of load flow, short-circuit and stability.

Answer : Wave trap is used to trap waves of higher frequencies entering generator or transformer units.

Answer : BJT is current controlled device.

Description : State the insulating materials used in motor. Write temperature class and withstand temperature ranges for them. 

Answer : The insulating materials used in motor are as belows: 1. Cotton, 2. Silk, or paper, 3. Press board, 4. Resins 5. PVC 6. Cellulose-Fiber, 7. Enameled coating, etc  ... Over 180° Mica, porcelain, ceramics, glass quartz, asbestos, treated glass fiber or treated asbestos. etc.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

Description : State the material used for making (1) Magnetic Core (2) Fuse element  

Answer : The material used for making of:  (1) Magnetic Core : Iron, cobalt, Nickel, CRGO, HRGO , silicon steel  (2) Fuse Element: Tin- lead wire, Tinned copper wire 

Description : List any four materials used for pattern making

Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Description : State properties of conductor material used for overhead conductor. 

Answer : Following are the properties of conductor material:-   1. High conductivity :- Material should have high conductivity 2. High mechanical strength:- Material should have sufficiently high mechanical strength ... available & less costly. 9. Scrap Value: - Material should have high scrap value. 

Description : State starters used for i) 3-Ph squirrel cage induction motor (3HP) ii) D.C. motor 

Answer : Name the starters used for following motors : i) 3 H.P. 3-Ph squirrel cage I.M: i) DOL starter OR ii) Star-Delta Starter OR ii) Auto transformer starter OR iii) Soft start starter.  ii) D.C Shunt Motor : 1) Armature resistance starter (Three Point Starter) OR 2) Four Point Starter 

Description : Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

Answer : Types of errors in measuring instruments:  A) Gross error: These are due to mistakes on the part of person using the instrument.  B) Systematic Error:  i) Instrumental Error: These ... multiplying factor.  C) Random error: These persist even after gross and systematic errors are removed. 

Description : Name the material used for :- (i) Moving coil (ii) Permanent magnet in PMMC instrument.

Answer : (i) Material used for Moving coil: Copper, Aluminum( some times)  (ii) Permanent magnets are made of special alloys such as :  Aluminum-Nickel-Cobalt (Alnicos)  Strontium-Iron  Neodymium-Iron-Boron  Samarium-Cobalt.

Description : State the material used for moving coil and former for PMMC instruments. 

Answer : Material Used for Moving Coil and Former for PMMC Instruments:  Material used for moving coil: Copper  Material used for Former: Aluminium

Description : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Answer : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

← Prev Question Next Question →
Ask a Question
Choose topic