1 Answer

The contacts of high voltage switches used in power system are submerged in oil. The main purpose of the oil is to extinguish the arc.

Like 0 like Dislike 0 dislike

Related questions

Answer : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should have low contact resistance, be clean and smooth, be of sufficient size and proper shape.

Answer : The voltage appearing across the contacts after opening of the circuit breaker is called recovery voltage.

Description : Why high voltage is used in power transmission?

Answer : The primary reason that power is transmitted at high voltages is to increase efficiency. ... The lower current that accompanies high voltage transmissionreduces resistance in the conductors aselectricity flows ... This means that thin, light-weight wires can beused in long-distance transmission.

Description : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Answer : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is 25 x 25

Description : Why high voltage can reduce power loss?

Answer : when voltage has increased due to reduced current flow, thus power loss given by ( I^2R) will be low due to reduced current(I^2) provided that resistance (R) is constant.

Description : Power factor of the system is kept high?

Answer : Power factor of the system is kept high to reduce line losses, to maximise the utilization of the capacities of generators, lines and transformers, to reduce voltage regulation of the line.

Answer : Oil switches are employed for high voltages and large currents circuits.

Description : In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Answer : In voltage source converter based HVDC transmission system the active power is controlled by changing phase angle of the converter ac input voltage

Answer : The arcing contacts in a circuit breaker are made of copper tungsten alloy.

Description : State the advantages of use of high voltage in transmission of Electric power. 

Answer : Advantages: 1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases, its ... high voltage transmission line, successful interconnection of transmission line is possible than low voltage. 

Answer : Overheating of relay contacts or contact born out is due to slow making and breaking of load circuit contacts, foreign matter on the contact surface, too low contact pressure.

Description : What are the advantages of high voltage transmission?

Answer : Advantages:  1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases ... line increases  12. As transmission voltage increases power handling capacity of transmission line increases 

Description : Why is it cheaper to transmit electrical energy at high voltage?

Answer : Because of the electrical energy was step upped by transformers the transformer have high efficiency than the electric energy is cheaper

Answer : Air blast circuit breakers for 400 kV power system are designed to operate in 50 millisecond.

Description : Limitation and application of High Voltage DC (HVDC)

Answer : Limitation and application of High Voltage DC (HVDC) :  Limitation:- 1) It is difficult to step up and step down DC voltage like AC voltage. 2) Special cooling ... conventional/non-conventional) 12) Increasing existing grid utilization. 13) Interconnection of different grids or networks

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

Answer : For measurements on high voltage capacitors, the suitable bridge is Schering bridge.

Description : What is meant by extra high voltage transmission?

Answer : HT & LT  two types transmission in industrial line 

Description : Why high voltage test is done?

Description : What is Extra High Voltage?

Description : What is a high voltage test?

Description : What is considered low voltage and high voltage?

Answer : yes High Voltage side of Transformer winding have more number of turns. and low voltage side of Transformer winding have less number of turns.

Description : A lightening arrester connected between the line and earth in a power system  (1) protects the terminal equipment against travelling surges (2) protects the transmission line against direct ... suppresses high frequency oscillations in the line (4) reflects back the travelling wave approaching it

Answer : A lightening arrester connected between the line and earth in a power system protects the terminal equipment against travelling surges

Description : With fault clearing time, the transient stability of a power system

Answer : With fault clearing time, the transient stability of a power system decreases

Answer : The steady state stability of the power system can be increased by connecting lines in parallel.

Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Answer : The voltage used for suburban trains in D.C. system is usually 600 to 750 V.

Description : How to calculate switches and MCB's cables to proper load ?

Description : Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 

Answer : MOSFET is metal oxide field effect transistor. MOSFET is a voltage controlled device. MOSFET is majority carrier device. MOSFET are of two one is n-channel MOSFET and p-channel MOSFET. Gate, ... . Hence, power MOSFET is operated at high enough gate-source voltage to minimize the conduction losses.

Answer : An induction motor has relatively high power factor at near full load.

Description : What is a high tension power line?

Answer : High tension power line is a high voltage of 115 kv and power line is underground transimissio used by urbun areas

Description : What is the advantage of high power factor?

Answer : Reduced copper losses Smaller conductor size Improve voltage regulation Increase system capability Less energy bill

Answer : Commonly used instruments in power system measurement are induction.

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

Description : The permissible voltage variation in transmission and distribution system is:  (A) ± 0.1% (B) ± 1% (C) ±10% (D) ± 25%

Answer : The permissible voltage variation in transmission and distribution system is: ±10%

Description : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Answer : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Description : What is the difference between a line voltage and low voltage control system?

Answer : In a distribution system, in order to improve power factor, the synchronous capacitors are installed at the receiving end.

Description : If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power ... factor is due to harmonic currents (D) total power factor is due to fundamental component of current

Answer : If non-linear loads are connected to the power system, then displacement power factor is not equal to the total power factor

Description : What are interconnected power system?

Answer : Interconnected power systems are those which connect different geographic regions. In Australia we have a National Electricity Grid which connects 6 states. Transfers of power occur between the states depending ... make more profit from this.National-Electricity-Market-Fact-Sheet.pdf (0,9 MB)

Description : What are the components of a power system?

Answer : generator Traansformer Conductors Insulators

Description :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

Answer :  An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when ZL = R-jXS

Description : In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

Answer : In an alternator, at lagging power factor the generated voltage per phase as compared to that at unity power factor must be more than terminal voltage.

Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

Answer : The primary reason for low power factor is supply system is due to installation of induction motors.

Description : Is the power line voltage available in our homes a dc or an ac voltage?

Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

Description : Explain starting system in diesel electric power plant.

Answer : Starting system in Diesel Electric Power Plant: It includes Storage battery, compressed air tanks, self-starter etc. The purpose of engine starting system is to rotate the engine initially while ... as Ammeters, Voltmeters, Wattmeters, Thermometers, Pressure gauges, Visible and audible alarm etc.

Description : Explain fuel system and air intake system in diesel electric power plant.

Answer : Fuel system and air intake system in diesel electric power plant :  Fuel system: It consists of storage tank, strainers, fuel transfer pump and all day fuel tank. The fuel oil is supplied ... Filters are provided to remove dust particles from air which may act as abrasive in the engine cylinder.

Description : What is the choice of size and number of generator units in interconnected power system?

Answer : Choice of Size and Number of Generating Units: 1. The size/rating and number of generating units in such way that they approximately match with the load curve as closely as possible. 2. In ... , if power plant is connected to grid system then generating unit of higher capacity can be installed.

← Prev Question Next Question →
Ask a Question
Choose topic