search
person

1 Answer

The ground wire should not be smaller than No 10 copper.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : How do magnets and copper wire make electricity?

Answer : According  to  Faradays  law , a changing  magnetic  field  on  a  conductor  induses  current  in  the  conductor  through   mutual  induction.

Description : A fuse wire should have :  (A) Low specific resistance and high melting point (B) Low specific resistance and low melting point (C) High specific resistance and high melting point (D) High specific resistance and low melting point

Answer : A fuse wire should have : High specific resistance and low melting point

Description : Why should switch be connected only on the live wire and never on the neutral wire?

Answer : Current runs from the transformer, through the protective device, through the load and back through the protective device (if on RCD).  If the protective device is only a CB the current passes ... the circuit will operate correctly but this is an unsafe practice and does not meet the standards.

Answer : In order to achieve high accuracy, the slide wire of a potentiometer should be as long as possible.

Description : On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be?

Answer : On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be zero at its upper end.

Description : On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be?

Answer : On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be upwards at its upper end.

Description : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

Answer : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be at the slot edge where coil enters or comes out of the slot.

Description : Describe the concept of virtual ground with reference to op-Amp.

Answer : Virtual ground concept:-In circuit point A is virtual ground. Figure shows inverting amplifier using op-amp. In this circuit non-inverting terminal is connected to the actual ground. Due to ... zero potential without actually grounding is known as virtual ground concept. Circuit diagram: 

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

Answer : To avoid electric shock from electrical appliances to the human body 

Description : Aluminium is not used as winding wire for the armature of a dc machine because  (1) aluminium has low resistivity (2) a large winding space is taken by aluminium conductors and creates ... ) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Answer : Aluminium is not used as winding wire for the armature of a dc machine because  (2) a large winding space is taken by aluminium conductors and creates jointing problems (3) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

Description : Why is aluminium used instead of copper for overhead cables?

Answer : Because copper reacts with atmosphere variation and it's cost High as compared to aluminium and aluminium is good property and less cost so aluminium is used

Description : Which is a semiconductor: copper, silicon, or neon?

Answer : Copper is a metal. Silicon is a semiconductor. Neon is inert gas.

Description : Compare copper and aluminium.

Answer : Copper Aluminium Resistivity is less Resistivity is more More weight Low weight Mechanically strong Mechanically weaker Specific Gravity high Specific Gravity Low ... Tensile strength is half of that of copper Used for winding Used for overhead lines

Description : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

Answer : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is 0.707

Description : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Answer : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

Description : Two copper conductors have equal length. The cross-sectional area of one conductor is four times that of the other. If the conductor having smaller cross-sectional area has a resistance of 40 ohms the resistance of other conductor will be?

Answer : Two copper conductors have equal length. The cross-sectional area of one conductor is four times that of the other. If the conductor having smaller cross-sectional area has a resistance of 40 ohms the resistance of other conductor will be 10 ohms.

Description : Current velocity through a copper conductor is

Answer : Copper brushes in D.C. machine are used where low voltage and high currents are involved.

Description : Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is?

Answer : Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is approximately equal to 1.

Description : explain skin effect in copper interconnects. what are the various ways of reducing this effect?

Answer : Skin effect generally observed in ac conductor in transmission network, in skin the current flowing through outer layer of conductor is more than iner area of conductor thus we can say the ... for reducing this effect we can use boundel conductor or used hollow conductor for power transmission

Description : What happens when a neutral wire touches a phase wire ?

Answer : Maximum current flow due to Short circuit, limited value of fuse will burn else apparatus and conductor will be damaged.

Description : Which wire can carry a higher current stranded wire or solid wire?

Answer : From the formula R=PL/A resistance rise with the fall of surface area ,inverse proportion relation between Resistance and Area ,so stranded wire has more area that a solid wire so more area less resistance. Less resistance/less electron flow opposition,more electron flow (current)

Description : State functions of ; i) Cable box ii) Guard wire iii) Shackle insulator iv) Stay wire used in service connection

Answer : i) Function of Cable box: To hold and inspect incoming and outgoing terminals  ii) Function of Guard wire : A grounded conductor placed beneath an overhead transmission line in order to ground ... in service connection: To give mechanical Support to pole, line and prevent leakage current if any

Description : The function of steel wire in ACSR conductors is (A) To take care of surges. (B) To reduce corona. (C) To reduce inductance. (D) To provide additional mechanical strength

Answer : The function of steel wire in ACSR conductors is To provide additional mechanical strength

Description : Increasing the number of turns of wire on the secondary of a transformer will  (A) Decrease the secondary current (B) Increase the primary current (C) Have no effect on the secondary current (D) Increase the secondary current

Answer : Increasing the number of turns of wire on the secondary of a transformer will Decrease the secondary current 

Description : For a round wire, the approximate value of fusing current is given by

Answer : For a round wire, the approximate value of fusing current is given by  K√d3

Description : lf the wire which is vertical to this page has electron flow downwards the conductor will have

Answer : lf the wire which is vertical to this page has electron flow downwards the conductor will have a counter-clockwise field in the plane of the paper

Description : Nichrome wire is an alloy of?

Answer : Nichrome wire is an alloy of nickel and chromium.

Description : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

Answer : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes 0.4 ohm.

Description : The resistance of a few meters of wire conductor in closed electrical circuit is?

Answer : The resistance of a few meters of wire conductor in closed electrical circuit is practically zero.

Description : Wire-wound resistors are unsuitable for use at high frequencies because they?

Answer : Wire-wound resistors are unsuitable for use at high frequencies because they exhibit unwanted inductive and capacitive effects.

Description : A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span?

Answer : A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span 4.0 cm.

Description : What happens when a current flows through a wire?

Answer : Current can produce two effect one is heating effect and second is magnetic effect.

Description : What is ACCC wire?

Answer : Aluminum Conductor Composite Core

Description : How is electricity passed through a wire?

Answer : A  wire contains  mobile  electrons  as  majority  charge  carriers  and  holes  as minority  charge carriers when  an emf  or   potential  diffrence is  provided , electrons  flow  in opposite  direction  with  holes(convection current  flow)

Description : Which color wire is neutral?

Answer : Black but I think it depends with the place.

Description : Ten coulombs of charge are placed on a solid copper sphere. Once the charge has come to rest, the ELECTRIC POTENTIAL inside the sphere is found to be: w) zero x) uniform inside the sphere and ... the sphere y) smaller than the electric potential outside the sphere z) varying as one over r squared

Answer : ANSWER: X -- UNIFORM INSIDE THE SPHERE AND EQUAL TO THE ELECTRIC POTENTIAL ON THE SURFACE OF THE SPHERE 

Description : The burden value in Potential Transformer (PT) should be ______ to achieve low errors in PT: A) low B) high C) medium D) infinite

Answer : The burden value in Potential Transformer (PT) should be high to achieve low errors in PT: 

Description : For selecting a circuit breaker, ______ should be determined.  (A) initial current that flows on occurrence of a short circuit only (B) transient current that flows at the time of circuit interruption only (C) resonant frequency only (D) (A) and (B) 

Answer : For selecting a circuit breaker, ______ should be determined. (A) initial current that flows on occurrence of a short circuit only (B) transient current that flows at the time of circuit interruption only (C) resonant frequency only (D) (A) and (B) 

Description : Copper wires are generally used for electrical power transmission instead of iron wire because : (1) copper is cheaper than iron (2) copper is lighter than iron (3) copper is a better conductor of electricity than iron (4) copper can take higher power than iron 

Answer : copper is a better conductor of electricity than iron

Description : A person can jump higher on the moon’s surface than on the earth because : (1) the moon’s surface is rough (2) the acceleration due to gravity in moon is smaller than that on the earth. (3) the moon is cooler than earth (4) the moon has no atmosphere

Answer : the acceleration due to gravity in moon is smaller than that on the earth.

Description : A copper disc has a hole. If the disc is heated, the size of the hole (1) increases (2) decreases (3) No change (4) first increases and than decreases

Answer : increases

Description : A thread is usually defined as a light weight process because an Operating System (OS) maintains smaller data structure for a thread than for a process. In relation to this, which of the following ... separate stack for each thread. (D) OS does not maintain virtual memory state for each thread.

Answer : (B) OS maintains only CPU registers for each thread.

Description : An oil drop spreads over water because (1) oil is lighter than water (2) oil is more viscous (3) oil does not mix with water (4) surface tension of oil is much smaller than that of water

Answer : surface tension of oil is much smaller than that of water

Description : Two stones of different masses are dropped simultaneously from the top of a building (1) Smaller stone reaches the ground earlier (2) Larger stone reaches the ground earlier (3) Both the stones reach the ground at the same time (4) Depends on the composition of the stone

Answer : Both the stones reach the ground at the same time

Answer : Series motor should not be started on no-load.

← Prev Question Next Question →
editChoose topic
...