1 Answer

Thermal overload relays are used to protect the motor against overcurrent due to heavy loads.

Like 0 like Dislike 0 dislike

Related questions

Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

Description : IDMT relays are used to protect the transformer against :  (A) Internal short -circuits (B) Open circuits (C) External short circuits (D) Oil leakage

Answer : IDMT relays are used to protect the transformer against : External short circuits

Answer : To protect most of the electrical equipment handling low power, the types of relays used are thermocouple, electronic and bimetallic.

Answer : A thermal protection switch can protect against overload.

Answer : Overload relays are of induction, solid state, thermal, electromagnetic type.

Answer : The single phasing relays are used for the protection of three phase motors.

Answer : Impedance relays are used for phase faults on long line.

Answer : Discrimination between main and back up protection is provided by the use of relays which are slow.

Answer : Protective relays are devices that detect abnormal conditions in electrical circuits by measuring constantly the electrical quantities which differ during normal and abnormal conditions.

Answer : Directional relays are based on flow of power.

Description : D.C. shunt relays are made of?

Answer : D.C. shunt relays are made of many turns of thin wire.

Answer : Relays can be designed to respond to changes in resistance, reactance or impedance voltage and current, light intensity, temperature.

Answer : Thermal circuit breaker has delayed trip action.

Description : How many types of types of relays are there?

Description : Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are best ... (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

Answer : Consider the following statements. Which of these statements are correct ?  (1) Reactance relays are preferred for ground fault relaying  (2) Impedance relays are most suitable for:protecting long transmission lines  (3) Mho relays are ... (1) and (3) (C) (2) and (4) (D) (1), (2) and (4)

Description : Classify condensers used in thermal power station. Explain each type in brief. 

Answer : Types of condenser: Classification: 1. Jet Condenser (Mixing Type) 2. Surface condenser (non Mixing type)  Explanation:-   1. Jet Condenser (Mixing Type) In Jet condenser the steam ... there in no direct contact between the steam and cooling water. This condensate is reused in boiler. 

Description : The overall efficiency of Thermal Power Plant is equal to _______________ .  (A) Regenerative Cycle Efficiency (B) Renkine Cycle Efficiency (C) Carnot cycle efficiency (D) None of the above

Answer : The overall efficiency of Thermal Power Plant is equal to Regenerative Cycle Efficiency. 

Description : Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Answer : Types of Triggering: 1) Forward voltage triggering 2) Thermal triggering (Temperature triggering) 3) Radiation triggering (Light triggering) 4) dv/dt triggering 5) Gate triggering ... generated leakage current increases. This current gets multiplied internally and thyristor is turned on. 

Description : Define thermal runaway.

Answer : Thermal runaway  The problem with increasing temperature causing increasing collector current is that more current increase the power dissipated by the transistor which, in turn, increases its temperature ... self-reinforcing cycle is known as thermal runaway, which may destroy the transistor. 

Description : "Efficiency of thermal power station is low". — Justify. 

Answer : Justification: Efficiency of thermal power station is low":- Overall efficiency of T.P.P depends upon efficiency of boiler, turbine and alternator. The heat produced due to combustion of coal ... losses in thermal power plant is 71%, So efficiency of thermal power plant is less about 29% 

Description : State advantages of Pulverized coal w.r.t. thermal power plant. 

Answer : Advantages of Pulverized coal w.r.t. thermal power plant.  1. Due to pulvarization amount of fuel required to produce same amount of heat reduces. 2. Time required for combution reduces ... of air and thorough mixing of air and fuel, very high-combustion temperatures can be attained.

Description : State the function of super heater of a thermal power plant. 

Answer : Function of Super heater: -  Its function is to increase the temperature of steam by absorbing heat from exhausted hot flue gases.

Description : Describe thermal runaway of transistor and explain how it can be avoided.

Answer : Concept of thermal runaway:  1.We know that  IC = β IB + (1+ β) ICO  Where ICO is the leakage current and ICO is strongly dependent on temperature. 2. Leakage current approximately doubles for ...   Thermal runaway can be avoided by : 1) Using stabilization circuitry 2) Heat sink 

Description : State the function of cooling tower and condenser in thermal power station.

Answer : 1. Condenser:   Function of condenser is to convert exhaust steam again into water by reducing its temperature with the help of cold water. Also it reduces back pressure of steam turbine 2 ... tower : The function of cooling tower is to reduce the temperature of water coming from condenser.

Description : Write any four advantages and four disadvantages of thermal power plant.

Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Explain ash disposal and dust collection in a thermal power plant.

Answer : Ash disposal:-  Various methods of disposal of ash are:  Mechanical handling system.  Pneumatic system. Hydraulic system  Steam jet system  Commonly used ash handling ... be done either manually or automatically.  This removed fly ash is collected in separate container

Description : State any four factors governing Selection of site for thermal power station. 

Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Description : In a thermal power plant, ash is collected in

Answer : In a thermal power plant, ash is collected in hoppers or bunkers

Description : The unit heat rate characteristic of a thermal power unit shows :  (A) Heat input per kWh of output versus the megawatt output of unit  (B) Heat input per kW of output versus the megawatt output ... hour output of unit  (D) Heat input per kW of output versus the megawatt hour output of unit

Answer : The unit heat rate characteristic of a thermal power unit shows : Heat input per kWh of output versus the megawatt output of unit 

Description : What is thermal runaway of a transistor?

Description : A relay used for protection of motors against overload is :  (A) Impedance relay (B) Electromagnetic attraction type (C) Thermal relay (D) Buchholz's relay

Answer : A relay used for protection of motors against overload is : Thermal relay

Description : Which type of protection is provided on a generator to protect against stator insulation failure? A) Differential protection B) Overcurrent relay C) Thermocouple actuated alarm D) Reverse power relay

Answer : Which type of protection is provided on a generator to protect against stator insulation failure? A) Differential protection B) Overcurrent relay C) Thermocouple actuated alarm D) Reverse power relay 

Description : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

Answer : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ? Δ-Δ connection

Description : Firewalls are used to protect a communication network system against: (A) Unauthorized attacks (B) Virus attacks (C) Data-driven attacks (D) Fire-attacks

Answer : Answer: A In computing, a firewall is a network security system that monitors and controls the incoming and outgoing network traffic based on predetermined security rules. A firewall typically establishes a ... outside network, such as the Internet, that is assumed to not be secure or trusted.

Description : Differential relays are used for the protection of equipments against   (a) Internal faults (b) Over current (c) Reverse current (d) Reverse power

Description : Define the following terms with respect to protective relays i) Relay time ii) Reset current iii) Plug setting multiplier and iv) Time setting multiplier

Answer : 1) Relay Time: The time interval between occurrence of fault and closure of relay contacts.  2) Reset Current: The value of current below which the relay resets and comes back to ... The adjustment arrangement provided for setting the operation time of relay is known as Time setting multiplier. 

Description :  For the protection of parallel feeders fed from one end, the relays used are: A) non-directional relays at the source-end and directional relays at the load-end B) non-directional relays at both the ... at the source-end and non-directional at the load-end D) directional relays at both the ends

Answer : For the protection of parallel feeders fed from one end, the relays used are: non-directional relays at the source-end and directional relays at the load-end

Description : Magnetic keepers are used to protect magnets from : (1) Earth’s magnetic field (2) effect of other magnets (3) self-demagnetization (4) demagnetization due to heating 

Answer : self-demagnetization

Description : Electrical contact materials used in switches, brushes and relays must possess   (A) high thermal conductivity and high melting point  (B) Low thermal conductivity and low melting point   (C) High thermal conductivity and low melting point  (D) Low thermal conductivity and high melting point.

Answer : Electrical contact materials used in switches, brushes and relays must possess high thermal conductivity and high melting point 

Description : Surge absorbers are used for protection against

Answer : Surge absorbers are used for protection against low voltage high frequency oscillations

Answer : A fuse in a motor circuit provides protection against short-circuit and overload.

Description : Reactance relays are employed for Phase faults in : (A) Short lines (B) Medium lines (C) Long lines (D) Any line

Answer : Reactance relays are employed for Phase faults in : Short lines

Description : The main function of white blood cells in the body is to (1) carry oxygen (2) help in clot formation (3) produce more red cells (4) protect body against diseases 

Answer : protect body against diseases

Description : Earth wire on EHV overhead transmission line is provided to protect the line against:

Answer : Earth wire on EHV overhead transmission line is provided to protect the line against: lightening surge

Description : In order to reduce the voltage surges due to current chopping and capacitive current breaking, we connect (A) A resistor across the CB contacts. (B) A capacitor across the CB contacts. (C) An inductor across the CB contacts. (D) A switch across the CB contacts

Answer : In order to reduce the voltage surges due to current chopping and capacitive current breaking, we connect A resistor across the CB contacts.

Description : Varnishes protect the insulating materials against (a) dust and oil (b) moisture, dirt and oil (c) moisture and fire hazards (d) None of the above

Description : For protection of rotating machines against lightning surges _______ is used.  (1) lightning arrester (2) capacitor (3) combination of lightning arrester and capacitor (4) lightning conductor and arrester

Answer : For protection of rotating machines against lightning surges combination of lightning arrester and capacitor is used. 

Description : Explain over-current protection of transformer.

Answer : Over-Current Protection of Transformer: Simple over-current & earth fault protection of transformer against external shortcircuit and excessive overloads is shown in the above figure. The ... trip command to the circuit breaker and the transformer is disconnected from load or fault.

Description : Describe over current relay with time-current characteristic.

Answer : Over current relay with time-current characteristics:- 1. Definite time over current relay: Operating time is constant, the relays operates after a predetermined time when the current exceeds the pickup ... of fault current and definite time characteristics at higher values of fault current.

← Prev Question Next Question →
Ask a Question
Choose topic