In a transformer the tappings are generally provided on?

Question

asked Mar 19, 2018 by anonymous

53 views

Please log in or register to answer this question.

1 Answer

← Prev Question Next Question →

Related questions

asked Mar 19, 2018 by anonymous

Spacers are provided between adjacent coils?

Last answer: Spacers are provided between adjacent coils to provide free passage to the cooling oil.

0 like 0 dislike

201 views 1 answer

asked Mar 19, 2018 by anonymous

In a power or distribution transformer about 10 percent end turns are heavily insulated?

Last answer: In a power or distribution transformer about 10 percent end turns are heavily insulated to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns.

0 like 0 dislike

71 views 1 answer

asked Mar 19, 2018 by anonymous

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Last answer: In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

0 like 0 dislike

104 views 1 answer

asked Mar 19, 2018 by anonymous

The size of a transformer core will depend on?

Last answer: The size of a transformer core will depend on frequency and area of the core.

0 like 0 dislike

69 views 1 answer

asked Mar 19, 2018 by anonymous

If a transformer is switched on to a voltage more than the rated voltage?

Last answer: If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

0 like 0 dislike

70 views 1 answer

asked Mar 19, 2018 by anonymous

An open-circuit test on a transformer is conducted primarily to measure?

Last answer: The open-circuit test in a transformer is used to measure

0 like 0 dislike

281 views 2 answers

asked Mar 19, 2018 by anonymous

A no-load test is performed on a transformer to determine?

Last answer: A no-load test is performed on a transformer to determine magnetizing current and loss.

0 like 0 dislike

85 views 1 answer

asked Mar 19, 2018 by anonymous

The transformer ratings are usually expressed in terms of?

Last answer: The transformer ratings are usually expressed in terms of kVA.

0 like 0 dislike

212 views 1 answer

asked Mar 19, 2018 by anonymous

Reduction in core losses and increase in permeability are obtained with transformer employing?

Last answer: Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

0 like 0 dislike

592 views 1 answer

asked May 22, 2020 by anonymous

Explain the effect of Harmonics on the Transformer.

Last answer: Effect of Harmonics on the Transformer: 1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations. 5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

0 like 0 dislike

33 views 1 answer

asked May 10, 2020 by anonymous

Transformer on DC

Write about transformer on DC.

Last answer: Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

0 like 0 dislike

232 views 1 answer

asked Mar 19, 2018 by anonymous

Sumpner's test is conducted on transformer to determine?

Last answer: Sumpner's test is conducted on transformer to determine temprature.

0 like 0 dislike

92 views 1 answer

asked Mar 19, 2018 by anonymous

The transformer laminations are insulated from each other by?

Last answer: The transformer laminations are insulated from each other by thin coat of varnish.

0 like 0 dislike

71 views 1 answer

asked Mar 19, 2018 by anonymous

The purpose of providing an iron core in a transformer is to?

Last answer: The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

0 like 0 dislike

83 views 1 answer

asked Mar 19, 2018 by anonymous

The no load current in a transformer lags behind the applied voltage by an angle of about?

Last answer: The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

0 like 0 dislike

79 views 1 answer

asked Mar 19, 2018 by anonymous

The purpose of providing iron core in a step-up transformer is?

Last answer: The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

0 like 0 dislike

287 views 1 answer

asked Mar 19, 2018 by anonymous

The thickness of laminations used in a transformer is usually?

Last answer: The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

0 like 0 dislike

67 views 1 answer

asked Mar 19, 2018 by anonymous

The function of conservator in a transformer is?

Last answer: conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

0 like 0 dislike

105 views 3 answers

asked Mar 19, 2018 by anonymous

The main reason for generation of harmonics in a transformer could be?

Last answer: The main reason for generation of harmonics in a transformer could be saturation of core.

0 like 0 dislike

71 views 1 answer

asked Mar 19, 2018 by anonymous

The leakage flux in a transformer depends upon?

Last answer: The leakage flux in a transformer depends upon load current.

0 like 0 dislike

105 views 1 answer

asked Mar 19, 2018 by anonymous

The value of flux involved in the e.m.f. equation of a transformer is ?

Last answer: The value of flux involved in the e.m.f. equation of a transformer is maximum value.

0 like 0 dislike

130 views 1 answer

asked Mar 19, 2018 by anonymous

The function of breather in a transformer is?

Last answer: The function of breather in a transformer is to arrest flow of moisture when outside air enters the transformer.

0 like 0 dislike

110 views 1 answer

asked Mar 19, 2018 by anonymous

In a transformer the resistance between its primary and secondary should be?

Last answer: In a transformer the resistance between its primary and secondary should be infinity.

0 like 0 dislike

101 views 1 answer

asked Mar 19, 2018 by anonymous

If a transformer is continuously operated the maximum temperature rise will occur in?

Last answer: If a transformer is continuously operated the maximum temperature rise will occur in windings.

0 like 0 dislike

56 views 1 answer

asked Mar 19, 2018 by anonymous

The hum in a transformer is mainly attributed to?

Last answer: The hum in a transformer is mainly attributed to magnetostriction.

0 like 0 dislike

86 views 1 answer

asked Mar 19, 2018 by anonymous

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last answer: In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

0 like 0 dislike

91 views 1 answer

asked Mar 19, 2018 by anonymous

The path of magnetic flux in a transformer should have?

Last answer: The path of magnetic flux in a transformer should have low reluctance.

0 like 0 dislike

272 views 1 answer

asked Mar 19, 2018 by anonymous

No-load current in a transformer?

Last answer: No-load current in a transformer lags behind the voltage by about 75°.

0 like 0 dislike

61 views 1 answer

asked Mar 19, 2018 by anonymous

Which winding in a transformer has more number of turns ?

Last answer: High voltage winding in a transformer has more number of turns.

0 like 0 dislike

114 views 1 answer

asked Mar 19, 2018 by anonymous

In a transformer routine efficiency depends upon?

Last answer: In a transformer, routine efficiency depends upon load current and power factor of load.

0 like 0 dislike

90 views 1 answer

asked Mar 19, 2018 by anonymous

Noise level test in a transformer is a?

Last answer: Noise level test in a transformer is a type test.

0 like 0 dislike

70 views 1 answer

asked Mar 19, 2018 by anonymous

In the transformer which winding has got more cross-sectional area?

Last answer: In the transformer low voltage winding has got more cross-sectional area.

0 like 0 dislike

133 views 1 answer

asked Mar 19, 2018 by anonymous

The use of higher flux density in the transformer design?

Last answer: The use of higher flux density in the transformer design reduces weight per kVA.

0 like 0 dislike

88 views 1 answer

asked Mar 19, 2018 by anonymous

The chemical used in breather for transformer should have the quality of?

Last answer: The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

0 like 0 dislike

95 views 1 answer

asked Mar 19, 2018 by anonymous

The core used in high frequency transformer is usually?

Last answer: The core used in high frequency transformer is usually air core .

0 like 0 dislike

49 views 1 answer

asked Mar 19, 2018 by anonymous

In an actual transformer the iron loss remains practically constant from no load to full load because?

Last answer: In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

0 like 0 dislike

77 views 1 answer

asked Mar 19, 2018 by anonymous

Transformer breaths in when?

Last answer: Transformer breaths in when load on it decreases.

0 like 0 dislike

67 views 1 answer

asked Mar 19, 2018 by anonymous

Which type of winding is used in 3 phase shell-type transformer ?

Last answer: Sandwich type winding is used in 3 phase shell-type transformer.

0 like 0 dislike

108 views 1 answer

asked Mar 19, 2018 by anonymous

what do not change in transformer?

Last answer: Frequency and power are constant in transformers. Suppose we apply 50 Hz input frequency then the output frequency will also be 50 Hz whether the transformer is step up or step down. Similar ... is decreased on secondary side and hence power on primary side and secondary side remains constant.

0 like 0 dislike

78 views 1 answer

asked Apr 28, 2020 by anonymous

Even at no-load, a transformer draws current from the mains. Why?

1 like 0 dislike

73 views 0 answers

asked Jul 27, 2019 by anonymous

State and justify which of the following two transformers is better: Transformer A = 4% voltage regulation Transformer B = 6% voltage regulation

Last answer: Transformer A with 4% voltage regulation is better. Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

0 like 0 dislike

102 views 1 answer

asked Mar 19, 2018 by anonymous

A transformer cannot raise or lower the voltage of a D.C. supply because?

Last answer: A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

0 like 0 dislike

137 views 1 answer

asked Mar 19, 2018 by anonymous

Efficiency of a power transformer is of the order of?

Last answer: The efficiency of a power transformer is of the order of 98 percent.

0 like 0 dislike

60 views 1 answer

asked Mar 19, 2018 by anonymous

The maximum efficiency of a distribution transformer is?

Last answer: The maximum efficiency of a distribution transformer is at 50% full load.

0 like 0 dislike

58 views 1 answer

asked Mar 19, 2018 by anonymous

The power transformer is a constant?

Last answer: The power transformer is a constant main flux device.

0 like 0 dislike

43 views 1 answer

asked Mar 19, 2018 by anonymous

The magnetising current of a transformer is usually small because it has?

Last answer: The magnetising current of a transformer is usually small because it has small air gap.

0 like 0 dislike

61 views 1 answer

asked Mar 19, 2018 by anonymous

The full-load copper loss of a transformer is 1600 W At half-load, the copper loss will be?

Last answer: The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.

0 like 0 dislike

68 views 1 answer

asked Mar 19, 2018 by anonymous

The secondary of a current transformer is always short-circuited under operating conditions because it?

Last answer: The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

0 like 0 dislike

75 views 1 answer

asked Mar 19, 2018 by anonymous

The noise produced by a transformer is termed as?

Last answer: The noise produced by a transformer is termed as hum.

0 like 0 dislike

77 views 1 answer

asked Mar 19, 2018 by anonymous

The maximum load that a power transformer can carry is limited by its?

Last answer: The maximum load that a power transformer can carry is limited by its voltage ratio.

0 like 0 dislike

104 views 1 answer

anonymous · Answer 1 · 2018-03-19T21:32:00+0000

answered Mar 19, 2018 by anonymous

In a transformer, the tappings are generally provided on low voltage side.

In a transformer the tappings are generally provided on?

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions