During short circuit test iron losses are negligible because?

Question

asked Mar 19, 2018 by anonymous

74 views

Please log in or register to answer this question.

1 Answer

← Prev Question Next Question →

Related questions

asked Mar 19, 2018 by anonymous

During open circuit test of a transformer?

Last answer: During open circuit test of a transformer primary is supplied rated voltage.

0 like 0 dislike

78 views 1 answer

asked Mar 19, 2018 by anonymous

The secondary of a current transformer is always short-circuited under operating conditions because it?

Last answer: The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

0 like 0 dislike

74 views 1 answer

asked Mar 19, 2018 by anonymous

In an actual transformer the iron loss remains practically constant from no load to full load because?

Last answer: In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

0 like 0 dislike

77 views 1 answer

asked Apr 27, 2020 by anonymous

Explain the procedure to perform Short Circuit test on single phase transformer with circuit diagram.

0 like 0 dislike

69 views 0 answers

asked Sep 27, 2017 by anonymous

in short circuit test of transformer which side is short circuited?

Last answer: Low voltage side is short circuited.

1 like 0 dislike

140 views 1 answer

asked Sep 27, 2017 by anonymous

in short circuit test of transformer which side is low voltage side and which side is high voltage side?

Last answer: Primary is high voltage side and Secondary is low Voltage side.

1 like 0 dislike

97 views 1 answer

asked Sep 3, 2017 by anonymous

what is short circuit test in transformer?

Last answer: In short circuit test of transformer the low voltage side is short circuited . On high voltage side the voltmeter is connected in parallel and ammeter in series and also a wattmeter is ... circuit test is done for determining impedance and losses. In this test iron losses is neglected.

0 like 0 dislike

134 views 1 answer

asked Mar 19, 2018 by anonymous

An open-circuit test on a transformer is conducted primarily to measure?

Last answer: The open-circuit test in a transformer is used to measure

0 like 0 dislike

277 views 2 answers

asked Mar 19, 2018 by anonymous

Reduction in core losses and increase in permeability are obtained with transformer employing?

Last answer: Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

0 like 0 dislike

592 views 1 answer

asked Mar 19, 2018 by anonymous

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Last answer: In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

0 like 0 dislike

103 views 1 answer

asked Mar 19, 2018 by anonymous

Noise level test in a transformer is a?

Last answer: Noise level test in a transformer is a type test.

0 like 0 dislike

70 views 1 answer

asked Mar 19, 2018 by anonymous

A no-load test is performed on a transformer to determine?

Last answer: A no-load test is performed on a transformer to determine magnetizing current and loss.

0 like 0 dislike

84 views 1 answer

asked Mar 19, 2018 by anonymous

Sumpner's test is conducted on transformer to determine?

Last answer: Sumpner's test is conducted on transformer to determine temprature.

0 like 0 dislike

92 views 1 answer

asked Mar 19, 2018 by anonymous

Atmospheric temperature during day and night is taken care of by which part of the transformer?

The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

Last answer: The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by conservator.

0 like 0 dislike

45 views 1 answer

asked Mar 19, 2018 by anonymous

The purpose of providing an iron core in a transformer is to?

Last answer: The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

0 like 0 dislike

83 views 1 answer

asked Mar 19, 2018 by anonymous

The purpose of providing iron core in a step-up transformer is?

Last answer: The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

0 like 0 dislike

285 views 1 answer

asked Mar 19, 2018 by anonymous

If the supply frequency to the transformer is increased, the iron loss will?

Last answer: If the supply frequency to the transformer is increased, the iron loss will increase.

0 like 0 dislike

102 views 1 answer

asked Mar 19, 2018 by anonymous

Iron loss of a transformer can be measured by?

Last answer: Iron loss of a transformer can be measured by low power factor wattmeter.

0 like 0 dislike

62 views 1 answer

asked Mar 19, 2018 by anonymous

When secondary of a current transformer is open-circuited its iron core will be?

Last answer: When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

0 like 0 dislike

101 views 1 answer

asked May 17, 2018 by anonymous

A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit

A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit test is performed on it with 90% of the rated currents flowing in its both LV and HV windings, he measured loss is 81 W. The transformer has maximum efficiency when operated at (A) 50.0% of the rated current (B) 64.0% of the rated current (C) 80.0% of the rated current (D) 88.8% of the rated current

Last answer: A single-phase transformer has no-load loss of 64 W, as obtained from an open circuit test. When a short-circuit test is performed on it with 90% of the rated currents flowing in its both ... measured loss is 81 W. The transformer has maximum efficiency when operated at 80.0% of the rated current

0 like 0 dislike

203 views 1 answer

asked Mar 19, 2018 by anonymous

Short circuit test on transformers is conducted to determine?

Last answer: Short circuit test on transformers is conducted to determine copper losses.

0 like 0 dislike

107 views 1 answer

asked Mar 19, 2018 by anonymous

A transformer cannot raise or lower the voltage of a D.C. supply because?

Last answer: A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

0 like 0 dislike

137 views 1 answer

asked Mar 19, 2018 by anonymous

The magnetising current of a transformer is usually small because it has?

Last answer: The magnetising current of a transformer is usually small because it has small air gap.

0 like 0 dislike

60 views 1 answer

asked Mar 19, 2018 by anonymous

The efficiency of a transformer, under heavy loads, is comparatively low because?

Last answer: The efficiency of a transformer, under heavy loads, is comparatively low because copper loss becomes high in proportion to the output.

0 like 0 dislike

64 views 1 answer

asked Sep 27, 2017 by anonymous

in open circuit or no load test of transformer which side is open circuited?

Last answer: High Voltage side is open circuited.

1 like 0 dislike

91 views 1 answer

asked Sep 27, 2017 by anonymous

in open circuit or no load test of transformer which side is low voltage side and which side is high voltage side?

Last answer: Primary side is low voltage side and secondary side is high voltage side.

1 like 0 dislike

94 views 1 answer

asked Mar 20, 2018 by anonymous

The short circuit in any winding of the transformer is the result of?

Last answer: The short circuit in any winding of the transformer is the result of impulse voltage.

0 like 0 dislike

131 views 1 answer

asked May 17, 2020 by anonymous

Equivalent circuit of transformer

Last answer: Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

0 like 0 dislike

226 views 2 answers

asked Apr 28, 2018 by anonymous

If a 5-bus test system contains 6 transmission lines and one transformer, how many non- zero elements are

If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

Last answer: If a 5-bus test system contains 6 transmission lines and one transformer, 19 non-zero elements are there in the system Y-bus.

0 like 0 dislike

2.9k views 1 answer

asked Apr 30, 2018 by anonymous

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Last answer: At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

0 like 0 dislike

115 views 1 answer

asked Mar 19, 2018 by anonymous

Spacers are provided between adjacent coils?

Last answer: Spacers are provided between adjacent coils to provide free passage to the cooling oil.

0 like 0 dislike

201 views 1 answer

asked Mar 19, 2018 by anonymous

In a transformer the tappings are generally provided on?

Last answer: In a transformer, the tappings are generally provided on low voltage side.

0 like 0 dislike

53 views 1 answer

asked Mar 19, 2018 by anonymous

The transformer ratings are usually expressed in terms of?

Last answer: The transformer ratings are usually expressed in terms of kVA.

0 like 0 dislike

210 views 1 answer

asked Mar 19, 2018 by anonymous

The transformer laminations are insulated from each other by?

Last answer: The transformer laminations are insulated from each other by thin coat of varnish.

0 like 0 dislike

71 views 1 answer

asked Mar 19, 2018 by anonymous

In a power or distribution transformer about 10 percent end turns are heavily insulated?

Last answer: In a power or distribution transformer about 10 percent end turns are heavily insulated to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns.

0 like 0 dislike

70 views 1 answer

asked May 17, 2018 by anonymous

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage

A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is (A) 50.0% (B) 70.7% (C) 141.4% (D) 200.0%

Last answer: A 500 kVA, 3-phase transformer has iron losses of 300 W and full load copper losses of 600 W. The percentage load at which the transformer is expected to have maximum efficiency is 70.7%

0 like 0 dislike

673 views 1 answer

asked May 25, 2018 by anonymous

The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss

The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss as the fraction of its rated core loss is (a) 4% (b) 0.4% (c) 0.25% (d) 0.04%

0 like 0 dislike

90 views 0 answers

asked Mar 10, 2018 by anonymous

Explain the electrical losses of magnetic materials used for the cores of inductors and transformer.

0 like 0 dislike

68 views 0 answers

asked Apr 30, 2020 by anonymous

Polarity Test of Transformer

Last answer: .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

1 like 0 dislike

278 views 2 answers

asked Apr 27, 2020 by anonymous

Explain the open delta (delta-delta) test on transformer.

0 like 0 dislike

57 views 0 answers

asked Mar 27, 2018 by anonymous

For a transmission line with negligible losses, the lagging reactive power...

For a transmission line with negligible losses, the lagging reactive power (VAR) delivered at The receiving end, for a given receiving end voltage, is directly proportional to the?

Last answer: For a transmission line with negligible losses, the lagging reactive power (VAR) delivered at The receiving end, for a given receiving end voltage, is directly proportional to the line voltage drop.

0 like 0 dislike

256 views 1 answer

asked Mar 20, 2018 by anonymous

The duration of sudden short-circuit test on a synchronous motor is usually about?

Last answer: The duration of sudden short-circuit test on a synchronous motor is usually about one second.

0 like 0 dislike

116 views 1 answer

asked Apr 11, 2018 by anonymous

To limit the short circuit current during fault conditions:

To limit the short circuit current during fault conditions: (1) Reactors are used (2) Capacitors are used (3) A coil of high inductive reactance as compared to its resistance is used (4) Both (a) and (c)

0 like 0 dislike

62 views 0 answers

asked Apr 11, 2018 by anonymous

During 3-phase short circuit on a unloaded alternator, the dc component may be zero in

During 3-phase short circuit on a unloaded alternator, the dc component may be zero in (1) One phase only (2) Any two phases (3) All three phases (4) None of the above

0 like 0 dislike

75 views 0 answers

asked Apr 3, 2018 by anonymous

With the help of a schematic diagram explain how a overcurrent relay protects a line during short circuit fault.

0 like 0 dislike

73 views 0 answers

asked May 22, 2020 by anonymous

Explain the effect of Harmonics on the Transformer.

Last answer: Effect of Harmonics on the Transformer: 1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations. 5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

0 like 0 dislike

33 views 1 answer

asked May 22, 2020 by anonymous

List two special feature of welding transformer.

Last answer: Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

0 like 0 dislike

36 views 1 answer

asked May 22, 2020 by anonymous

State two applications of isolation transformer

Last answer: Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

0 like 0 dislike

25 views 1 answer

asked May 22, 2020 by anonymous

State why a transformer always have an efficiency of more than 90%.

Last answer: As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

0 like 0 dislike

31 views 1 answer

asked May 16, 2020 by anonymous

Single phase transformer

Last answer: Single phase Transformer Transformer

0 like 0 dislike

234 views 1 answer

anonymous · Answer 1 · 2018-03-19T21:02:13+0000

During short circuit test iron losses are negligible because the voltage applied on primary side is low.

During short circuit test iron losses are negligible because?

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions