search
person

1 Answer

When a given transformer is run at its rated voltage but reduced frequency, its core flux density is increased.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : If a transformer is switched on to a voltage more than the rated voltage?

Answer : If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

Description : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Answer : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

Description : When secondary of a current transformer is open-circuited its iron core will be?

Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

Answer : The core used in high frequency transformer is usually air core .

Answer : If the supply frequency to the transformer is increased, the iron loss will increase.

Description : A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

Answer : Leading

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

Description : A good voltage regulation of a transformer means?

Answer : A good voltage regulation of a transformer means output voltage fluctuation from no load to full load is least.

Description : The voltage transformation ratio of a transformer is equal to the ratio of?

Answer : The voltage transformation ratio of a transformer is equal to the ratio of secondary induced e.m.f. to primary induced e.m.f.

Answer : Transformer breaths in when load on it decreases.

Answer : Delta/star transformer works satisfactorily when on balanced as well as unbalanced loads.

Description : In a transformer the resistance between its primary and secondary should be?

Answer : In a transformer the resistance between its primary and secondary should be infinity.

Description : The maximum load that a power transformer can carry is limited by its?

Answer : The maximum load that a power transformer can carry is limited by its voltage ratio.

Description : Even at no-load, a transformer draws current from the mains. Why?

Answer : The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.

Answer : An ideal transformer will have maximum efficiency at a load such that copper loss equal to iron loss.

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

Description : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Answer : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Answer : At 0.866 time voltage value

Description : A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and frequency are doubled, the new core losses are (A) 140 W (B) 180 W (C) 240 W (D) 480 W

Answer : A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and frequency are doubled, the new core losses are 240 W

Description : The maximum flux in a transformer is φm when primary voltage is V and the frequency is f. If the primary voltage is 2 V and frequency is f/2, the flux will be (a) 4 φm (b) 0.25 φm (c) φm (d) 0.5 φm

Description : The voltage applied to the H.V. side of a transformer during S.C. test is 2% of the rated voltage. The core loss as the fraction of its rated core loss is (a) 4% (b) 0.4% (c) 0.25% (d) 0.04%

Description : Explain the effect of Harmonics on the Transformer.

Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

Description : List two special feature of welding transformer.

Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

Description : State two applications of isolation transformer

Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

Description : State why a transformer always have an efficiency of more than 90%.

Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

Description : Equivalent circuit of transformer

Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Description : Single phase transformer

Answer : Single phase Transformer Transformer

Description : What is the use of transformer?

Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

Description : Write about transformer on DC.

Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

Description : State any four characteristics of core type transformer.

Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

Description : Explain construction and working of single phase Auto transformer.

Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

Answer : No-load current in a transformer lags behind the voltage by about 75°.

Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

Answer : In the transformer low voltage winding has got more cross-sectional area.

Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

Answer : High voltage winding in a transformer has more number of turns.

Answer : The efficiency of a power transformer is of the order of 98 percent.

Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

Answer : The maximum efficiency of a distribution transformer is at 50% full load.

Answer : No-load current of a transformer has small magnitude and low power factor.

Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Answer : The power transformer is a constant main flux device.

Answer : In a transformer, the tappings are generally provided on low voltage side.

Answer : The use of higher flux density in the transformer design reduces weight per kVA.

Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

Answer : The transformer ratings are usually expressed in terms of kVA.

← Prev Question Next Question →
editChoose topic
...