# Iron loss of a transformer can be measured by?

Iron loss of a transformer can be measured by low power factor wattmeter.

## Related questions

Answer : In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

Answer : If the supply frequency to the transformer is increased, the iron loss will increase.

Description : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Answer : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

Description : Dielectric loss in a capacitor is best measured by (A) Wien Bridge (B) Schering Bridge (C) Anderson Bridge (D) Heaviside-Campbell Equal Ratio Bridge

Answer : Dielectric loss in a capacitor is best measured by Schering Bridge

Description : When secondary of a current transformer is open-circuited its iron core will be?

Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

Description : A ferrite core has less eddy current loss than an iron core because?

Answer : A ferrite core has less eddy current loss than an iron core because ferrites have high hysteresis.

Description : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is

Answer : A 40 kVA transformer has a core loss of 400 W and a full load copper loss of 800 W. The proportion of full load at maximum efficiency is 0.707

Answer : A direct current can be measured by a D.C. potentiometer in conjunction with a standard resistance.

Description : The self inductance of a coil can be measured using (A) Wien’s Bridge (B) Schering Bridge (C) Anderson’s Bridge (D) Wheatstone Bridge

Answer : The self inductance of a coil can be measured using Anderson’s Bridge

Answer : Resistances can be measured with the help of ohmmeters and resistance bridges.

Description : Corona loss in transmission lines can be reduced by (A) using small diameter conductors (B) using bundled conductors (C) using less spacing between conductors (D) increasing the transmission line voltage

Answer : Corona loss in transmission lines can be reduced by using bundled conductors

Answer : The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.

Answer : A moving iron instrument can be used for both D.C. and A.C.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

Description : How can power loss be reduced?

Description : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

Answer : The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is between 0.5 and unity

Answer : E.m.f. of a Weston cell is accurately measured by electrostatic voltmeter.

Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Description : The maximum load that a power transformer can carry is limited by its?

Answer : The maximum load that a power transformer can carry is limited by its voltage ratio.

Description : Eddy current damping cannot be used for moving iron instrument because

Answer : Eddy current damping cannot be used for moving iron instrument because the presence of a permanent magnet required for such purpose would affect the deflection and hence the reading of the instrument

Description : The load of a consumer is generally measured in terms of : (A) Volts (B) Amperes (C) Ampere hour (D) kW

Answer : The load of a consumer is generally measured in terms of : kW

Description : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

Answer : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be 20%.

Description : In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

Answer : In a battery, the difference between the no-load voltage and the measured voltage output is called Internal resistance

Description : Liquid flow rate is measured using (A) a pirani gauge (B) a pyrometer (C) an orifice plate (D) a bourdon tube

Answer : Liquid flow rate is measured using an orifice plate

Description : In a circuit containing R, L and C, power loss can take place in?

Answer : In a circuit containing R, L and C, power loss can take place in R only.

Description : Why high voltage can reduce power loss?

Answer : when voltage has increased due to reduced current flow, thus power loss given by ( I^2R) will be low due to reduced current(I^2) provided that resistance (R) is constant.

Answer : If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is 10°.

Answer : A transformer can have regulation closer to zero on leading power factor.

Description : What to look for when choosing an iron?

Answer : What to look for when choosing an iron? Today, the purchase of an iron is not a big problem. This piece of household appliances is presented in a wide range of stores. Each manufacturer tries to ... its presence increases the cost of the iron by an average of 10%. Good luck with your choice!

Description : Which is the best conductor: silver, carbon, or iron?

Answer : Silver is the best conductor. Carbon is the semiconductor. Iron have less conductance as compared to silver.

Description : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

Answer : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be either decreased or increased depending on the direction of the DC field

Description : The iron alloy, ALNICO is mainly used to make ________ A) Temporary magnets B) Permanent magnets C) Transmission lines D) None of these

Answer : The iron alloy, ALNICO is mainly used to make Permanent magnets

Description : In DC motor iron losses are occurred in?

Answer : In DC motor iron losses are occurred in the armature.

Description : In AC. circuits, laminated iron is invariably used in order to?

Answer : In AC. circuits, laminated iron is invariably used in order to reduce eddy current loss.

Answer : Iron losses in a D.C. machine are independent of variations in load.

Answer : In a D.C. generator, the iron losses mainly take place in armature rotor.

Answer : A transformer oil must be free from moisture.

Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

Description : In a transformer the resistance between its primary and secondary should be?

Answer : In a transformer the resistance between its primary and secondary should be infinity.

Description : The dielectric strength of transformer oil is expected to be?

Answer : The dielectric strength of transformer oil is expected to be 33 kV.

Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

Description : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

Answer : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by conservator.

Answer : The transformer laminations are insulated from each other by thin coat of varnish.

Description : The noise produced by a transformer is termed as?

Answer : The noise produced by a transformer is termed as hum.

Description : Weight Loss Tips

Answer : Weight Loss Tips Are you fed up of yourself being overweight? Are you looking for some effective weight loss tips? Then, your search ends here. In this article, you will get find an effective ... they are very easy and simple to follow, they are known to provide outstanding effects on the body.

Description : Hair Loss

Answer : Hair Loss How dreadful would you feel, if you start experiencing sudden hair loss in your life? Hairs form the crown of your entire body and so you need to keep it with great care. However, ... and natural hair loss tips to enjoy beautiful, shiny and thick hairs that will attract others, for sure.

Description : Anti-hair loss shampoo. How to choose?

Answer : The problem of hair loss has always been relevant. Almost every one of us periodically observes the remaining hairs on the comb. In this case, there is absolutely no need to panic, because ... Look for shampoos that contain medicinal substances such as burdock oil, nettle extract, or burdock juice.

Answer : Corona is nothing but the ionization of surrounding air around the conductor which produces hissing noise,

Description : State the factors affecting hysteresis loss.

Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

← Prev Question Next Question →