search
person

The hum in a transformer is mainly attributed to?

1 Answer

The hum in a transformer is mainly attributed to magnetostriction.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Light triggering is mainly used in

Answer : Light triggering is mainly used in High voltage direct current transmission

Answer : Silicon steel used in laminations mainly reduces hysteresis loss.

Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

Answer : In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

Description : In a power transformer, the fundamental frequency of the hum arising due to magnetostriction is  (a) equal to the line frequency (b) double the line frequency (c) 4 times the line frequency (d) not related to the line frequency

Answer : In a power transformer, the fundamental frequency of the hum arising due to magnetostriction is double the line frequency

Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.

Answer : If the supply frequency to the transformer is increased, the iron loss will increase.

Answer : A transformer can have regulation closer to zero on leading power factor.

Description : An open-circuit test on a transformer is conducted primarily to measure?

Answer : The open-circuit test in a transformer is used to measure

Description : A no-load test is performed on a transformer to determine?

Answer : A no-load test is performed on a transformer to determine magnetizing current and loss.

Description : The voltage transformation ratio of a transformer is equal to the ratio of?

Answer : The voltage transformation ratio of a transformer is equal to the ratio of secondary induced e.m.f. to primary induced e.m.f.

Description : Part of the transformer which is most subject to damage from overheating is?

Answer : Part of the transformer which is most subject to damage from overheating is winding insulation.

Description : If a transformer is switched on to a voltage more than the rated voltage?

Answer : If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

Description : Sumpner's test is conducted on transformer to determine?

Answer : Sumpner's test is conducted on transformer to determine temprature.

Description : The dielectric strength of transformer oil is expected to be?

Answer : The dielectric strength of transformer oil is expected to be 33 kV.

Answer : No-load current in a transformer lags behind the voltage by about 75°.

Answer : In the transformer low voltage winding has got more cross-sectional area.

Answer : High voltage winding in a transformer has more number of turns.

Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

Answer : Transformer breaths in when load on it decreases.

Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Answer : In a transformer, the tappings are generally provided on low voltage side.

Answer : The use of higher flux density in the transformer design reduces weight per kVA.

Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

Answer : The transformer ratings are usually expressed in terms of kVA.

Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

Answer : The leakage flux in a transformer depends upon load current.

Answer : Noise level test in a transformer is a type test.

Answer : The core used in high frequency transformer is usually air core .

Answer : The value of flux involved in the e.m.f. equation of a transformer is maximum value.

Answer :  Sandwich type winding is used in 3 phase shell-type transformer.

Answer : The function of breather in a transformer is to arrest flow of moisture when outside air enters the transformer.

Description : Reduction in core losses and increase in permeability are obtained with transformer employing?

Answer : Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

Answer : In a power or distribution transformer about 10 percent end turns are heavily insulated to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns.

Description : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Answer : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

Description : In a transformer the resistance between its primary and secondary should be?

Answer : In a transformer the resistance between its primary and secondary should be infinity.

Description : If a transformer is continuously operated the maximum temperature rise will occur in?

Answer : If a transformer is continuously operated the maximum temperature rise will occur in windings.

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

Description : The path of magnetic flux in a transformer should have?

Answer : The path of magnetic flux in a transformer should have low reluctance.

Description : what do not change in transformer?

Answer : Frequency and power are constant in transformers. Suppose we apply 50 Hz input frequency then the output frequency will also be 50 Hz whether the transformer is step up or step down. Similar ... is decreased on secondary side and hence power on primary side and secondary side remains constant.

Description : Explain the effect of Harmonics on the Transformer.

Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

Description : List two special feature of welding transformer.

Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

Description : State two applications of isolation transformer

Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

Description : State why a transformer always have an efficiency of more than 90%.

Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

Description : Equivalent circuit of transformer

Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Description : Single phase transformer

Answer : Single phase Transformer Transformer

Description : What is the use of transformer?

Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

← Prev Question Next Question →
editChoose topic
...