search
person
Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

1 Answer

image

Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below and above the 950 Khz in suitable steps. Everytime the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Answer : block diagram of FM super heterodyne radio receiver

Description : Define selectivity and sensitivity of AM Receiver. 

Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Description : Describe the functions of mixer and local oscillator in radio receiver

Answer : Frequency Mixer:- The function of frequency mixer is to heterodyne signal frequency fs and local oscillator frequency fo. At the output, it produces the difference frequency known as ... local oscillator frequency fo is then mixed with incoming frequency to give intermediate frequency. 

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Description : Draw the TRF receiver block diagram and explain its working. 

Answer : Explanation:- 1. TRF receivers are simple and having high sensitivity. The AM transmission takes place in MW band and SW band. MW frequency range is 540KHz to 1640KHz. 2. ... power level to drive the loudspeaker. 7. The loudspeaker converts electrical signal into original sound information.

Description : Write any two drawbacks of TRF radio receiver.

Answer : Drawbacks of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability. 

Description : Draw the circuit diagram of practical diode detector and explain its working. 

Answer : Circuit diagram of practical diode detector:  Explanation- The circuit operates in the following manner- The diode has been reversed so that now the negative envelope is demodulated. Due to this ... to produce AGC voltage. The DC AGC voltage is proportional to the amplitude of AM signal. 

Description : Explain the working of amplitude limiter in FM receiver with circuit diagram.

Answer : Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy  Circuit Diagram:

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz

Description : State the IF frequency and bandwidth of FM receiver.

Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Description : Describe the block diagram of FM superhetrodyne receiver

Answer : RF amplifier:- There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM broadcast the ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Description : Draw construction of Yagi-Uda antenna and explain.

Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

Description : Draw and explain block diagram of electronic communication system.

Answer : Block diagram of electronic communication system. Explanation Transducer: A transducer is usually required to convert the output of a source into an electrical signal that is suitable for ... etc. Output Transducer: The output transducer converts electrical signal in to sound signal.  

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Description : Draw and explain PLL as an FM demodulator.

Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Description : Draw the circuit diagram of limiter and explain its working.

Answer : Circuit diagram of amplitude limiter:- Explanation:- 1. In frequency modulation, the signal amplitude is held constant while the carrier frequency is varied. 2. Any noise that contaminates ... V p-p instead of the alternately driven into saturation and cutoff, it limits the signal amplitude

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

Description : Draw the diagram for PAM generation using transistors. Explain its working.

Answer : Explanation:-1. Transistor Q1 is used in the active region so it has been provided with DC biasing to its base. 2. Modulating signal is applied to the base of transistor Q1 3. In the emitter of ... . 7. In the time interval between sampling pulses output is zero. Thus we get the output as PAM.

Description : Draw the block diagram of AM transmitter, explain its operation.

Answer : AM transmitter is of two types i)High Level AM Transmitter ii)Low Level AM Transmitter i) RF crystal oscillator: It is a source of carrier signal of desired frequency. The circuit is ... AM signal is then applied to the transmitting antenna which radiates this AM signal into air or space. 

Description : In a broadcast communication receiver, most of the receiver selectivity is achieved in: (1) RF section (2) IF section (3) Mixer (4) Local oscillator 

Answer : In a broadcast communication receiver, most of the receiver selectivity is achieved in: RF section

Answer : A receiver has poor selectivity. It will also have poor blocking.

Description : Draw and label the circuit diagram of ratio detector 

Answer : Draw and label the circuit diagram of ratio detector  

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

Description : Define PAM, PWM, and PPM. Draw waveforms.

Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Description : Draw block diagram of basic electronic communication system and state the function of each block.

Answer : i) Input signal: - The information can be in the form of sound, picture or data coming from computer. ii) Input transducer: - it converts original information into equivalent electrical ... back to suitable form. vii) Output transducer: - It converts electrical signal into original form. 

Description : Draw amplitude modulated waveform in time domain and frequency domain with proper labeling.

Answer : AM in Time domain  AM in frequency domain

Description : Draw the structure of horn antenna and its radiation pattern. List its any two applications.

Answer : The structure of horn antenna Radiation pattern of Horn Antenna Application:- i) Used at microwave frequency. ii) Used in satellite tracking 

Description : 1. What is the most appropriate measure of a country's economic growth? 2. The famous player Pele is associated with which game? 3. By which antibodies are produced in the plasma of blood? 4. ... clouds is a low level cloud? 20. Which one of the Chola kings conquered Ceylon (Sinhal) first?

Answer : Answer : 1. Per capita real income 2. Football 3. Lymphocytes 4. Anthracite 5. Lord Dalhousie 6. Lok Sabha Speaker 7. Helium 8. Scotland 9. Damodar 10. Canning 11. Rules and regulations12. Liver 13. ... Pradesh 15. Shankaracharya 16. 1.65 cm 17. 22 March 18. Vienna 19. Stratocumulus 20. Rajaraja I

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Description : Define the transmission line? Draw it‟s general equivalent circuit.

Answer : Transmission line: A conductor or conductors designed to carry electricity or an electrical signal over large distances with minimum losses and distortion.  Equivalent circuit:

Description : Draw radiation pattern for following antenna i) Yagi-Uda antenna ii) Loop antenna iii) Dish antenna iv) Horn antenna

Answer : Type of antenna Radiation Patteren  Yagi-Uda antenna Loop antenna Dish antenna Horn antenna 

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

Description : Draw the circuit diagram of PWM using IC555. State its operation.

Answer : Operation: i. The timer IC555 is operated in monostable mode. ii. The negative going carrier pulses are to the differentiator formed by R1 & C1. The differentiator produces sharp negative ... . Thus PWM signal is generated at the output pin (3) of IC555 as monostablemultivibrator. 

Description : Draw Yagiuda antenna with its radiation pattern.

Answer : Construction of Yagi-Uda Antenna Radiation Pattern of Yagi-Uda Antenna

Description : Draw general equivalent circuit of transmission line.

Answer : Fig. General Equivalent circuit of transmission line 

Description : Draw the block diagram of PWM. List its advantages 

Answer : Block diagram of PWM:- Advantages of PWM:- 1. More immune to noise. 2. Synchronization between transmitter and receiver is not required. 3. Possible to separate out signal from noise.

Description : Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Answer : The radiation pattern for Half wave dipole antenna The radiation pattern for Folded dipole antenna.

Description : Explain the troubleshooting procedure for colour TV receiver system.

Answer : * Check the Antenna signal strength, whether it gives readings as per requirement. * As per the behavior of the screen or the speaker, check the different sections of TV receiver. * For Sound ... section, Horizontal Output Section. * If problem found, Replace/ Repair the Component and start the TV.

Description : Define and explain the term beam width related to antenna with a sketch.

Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Description : Explain virtual height with respect to wave propagation with neat sketch.

Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

Description : Why electromagnetic waves are said to be transverse wave ? Explain.

Answer : The electromagnetic waves are oscillations which propagate through free space. In electromagnetic waves the direction of electric field, magnetic field & propagation are mutually perpendicular. Hence electromagnetic waves are called as transverse wave.

Description : State the need of stub. Explain single stub and double stub matching.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

Description : State and explain the concept of transmission bandwidth.

Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

Description : Explain working of envelope detector with suitable diagram and waveform.

Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

← Prev Question Next Question →
editChoose topic
...