search
person
Explain the working of amplitude limiter in FM receiver with circuit diagram.

1 Answer

Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy 

Circuit Diagram:

image

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Description : Draw the circuit diagram of limiter and explain its working.

Answer : Circuit diagram of amplitude limiter:- Explanation:- 1. In frequency modulation, the signal amplitude is held constant while the carrier frequency is varied. 2. Any noise that contaminates ... V p-p instead of the alternately driven into saturation and cutoff, it limits the signal amplitude

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Answer : block diagram of FM super heterodyne radio receiver

Description : Describe the block diagram of FM superhetrodyne receiver

Answer : RF amplifier:- There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM broadcast the ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Description : Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Answer : With diode D2 reversed , O is positive with respect to b, so that Vab is a sum voltage rather than the difference it was in the discriminator it is now possible to connect a large capacitor ... of limiter stage due to large capacitor C5 .Hence, limiter stage is not used in ratio detector.  

Description : Draw the TRF receiver block diagram and explain its working. 

Answer : Explanation:- 1. TRF receivers are simple and having high sensitivity. The AM transmission takes place in MW band and SW band. MW frequency range is 540KHz to 1640KHz. 2. ... power level to drive the loudspeaker. 7. The loudspeaker converts electrical signal into original sound information.

Description : Explain with block diagram of Armstrong method of FM generation.

Answer : Explanation:- The crystal oscillator generates the carrier at low frequency typically at 1 MHz this is applied to the combining network and a 90o phase shifter. The modulating signal is passed through an ... power amplifier to raise the power level of the FM signal.  Phasor Diagram:-   

Description : State the IF frequency and bandwidth of FM receiver.

Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

Description : Draw the circuit diagram of practical diode detector and explain its working. 

Answer : Circuit diagram of practical diode detector:  Explanation- The circuit operates in the following manner- The diode has been reversed so that now the negative envelope is demodulated. Due to this ... to produce AGC voltage. The DC AGC voltage is proportional to the amplitude of AM signal. 

Description : Explain working of envelope detector with suitable diagram and waveform.

Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

Description : With the help of neat diagram, explain the working of phase discriminator.

Answer : Explanation:- This discriminator is also known as the center tuned discriminator or the Foster Seeley discriminator after its inventors. It is possible to obtain the same S- Shape response curve from a circuit in ... fin = fc, fin > fc + Δf and fin<fc- Δf should be given marks

Description : Draw the diagram for PAM generation using transistors. Explain its working.

Answer : Explanation:-1. Transistor Q1 is used in the active region so it has been provided with DC biasing to its base. 2. Modulating signal is applied to the base of transistor Q1 3. In the emitter of ... . 7. In the time interval between sampling pulses output is zero. Thus we get the output as PAM.

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Description : Explain pre-emphasis and de-emphasis concept in FM.

Answer : Pre-emphasis:- In an FM system the higher frequencies contribute more to the noise than the lower frequencies. Because of this all FM systems adopt a system of pre-emphasis where the higher frequencies are ... at receiver to improve the noise immunity Pre-emphasis/ De-emphasis graph:

Description : Draw and explain PLL as an FM demodulator.

Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Description : Explain reactance modulator for FM generation.

Answer : Explanation :- Audio modulating signal is applied to Q1 which varies the base voltage and current of Q1 according to the input information to be transmitted. The collector current ... lower the frequency & decrease capacitance increase the frequency and thus produce direct FM at output.

Description : List the types of FM detector. Explain any one of them.

Answer : Types of FM detector:- 1. Simple slope detector 2. Balanced slope detector 3. Phase discriminator(Foster seely discriminator) 4. Ratio detector 5. PLL detector Simple ... . If the IF amplitude is sufficiently limited prior to reaching the PLL and the loop is properly compensated 

Description : Draw neat block diagram of FM receiver and explain function of each block

Answer : Explanation:-  RF amplifier: There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Description : Draw amplitude modulated waveform in time domain and frequency domain with proper labeling.

Answer : AM in Time domain  AM in frequency domain

Description : Explain skip zone and skip distance with neat diagram.

Answer : Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wav of fixed frequency returns back to the earth. Skip zone: skip zone where signal is not detectable

Description : Describe the functions of mixer and local oscillator in radio receiver

Answer : Frequency Mixer:- The function of frequency mixer is to heterodyne signal frequency fs and local oscillator frequency fo. At the output, it produces the difference frequency known as ... local oscillator frequency fo is then mixed with incoming frequency to give intermediate frequency. 

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz

Description : Define selectivity and sensitivity of AM Receiver. 

Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Description : Write any two drawbacks of TRF radio receiver.

Answer : Drawbacks of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability. 

Description : Draw the block diagram of PCM receiver with the help of relevant wave form and explain its working

Answer : Block diagram of PCM receiver:- Explanation:- A PCM signal contaminated with noise is available at the receive input. The regeneration circuit at the receiver will separate PCM pulses from noise ... quantized PAM signal is passed through a low pass filter recovers the analog signal x (t).

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

Description : Draw and label the circuit diagram of ratio detector 

Answer : Draw and label the circuit diagram of ratio detector  

Description : Draw the circuit diagram of PWM using IC555. State its operation.

Answer : Operation: i. The timer IC555 is operated in monostable mode. ii. The negative going carrier pulses are to the differentiator formed by R1 & C1. The differentiator produces sharp negative ... . Thus PWM signal is generated at the output pin (3) of IC555 as monostablemultivibrator. 

Description : State the process FM detection? State it‟s any two types.

Answer : FM detection: In any radio that is designed to receive frequency modulated signals there is some form of FM demodulator or detector. This circuit takes in frequency modulated RF signals and takes the ... 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL)

Description : Give the expression for modulation index for AM and FM.

Answer : 1.Modulation index for AM ma=Vm / Vc Where Vm is modulating voltage Vc is the carrier voltage 2.Modulation index for FM mf=δ /fm where δ is the deviation fm is the modulating frequency

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Description : What are the different types of FM detector?

Answer : The different types of FM Detectors are: 1. Simple Slope Detector 2. Balanced Slope Detector 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL) 

Description : Compare between FM and PM 

Answer : PARAMETERS FM PM 1. Variable parameter of carrier. Frequency Phase 2. Variable parameter proportional to modulating voltage.  Frequency deviation Phase deviation.  3. Amplitude ... for transmitted power More Moderate 6. Signal to noise ratio Best Better

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Description : Draw and explain block diagram of electronic communication system.

Answer : Block diagram of electronic communication system. Explanation Transducer: A transducer is usually required to convert the output of a source into an electrical signal that is suitable for ... etc. Output Transducer: The output transducer converts electrical signal in to sound signal.  

Description : Draw the block diagram of AM transmitter, explain its operation.

Answer : AM transmitter is of two types i)High Level AM Transmitter ii)Low Level AM Transmitter i) RF crystal oscillator: It is a source of carrier signal of desired frequency. The circuit is ... AM signal is then applied to the transmitting antenna which radiates this AM signal into air or space. 

Description : In FM demodulation hard limiter and hand pass filter are used to remove (a) frequency variation in the FM wave (b) amplitude variation in FM wave (c) noise in the demodulated wave (d) amplitude variations in demodulated wave

Description : Describe the term virtual height with the help of diagram showing ionized layer and the path of wave.

Answer : Virtual height: -The incident wave returns back to the earth due to refraction. In this process it bends down gradually and not sharply, but the incident and reflected rays follow exactly ... . It is also defined as the maximum height that the hypothetical reflected wave would have reached. 

Description : Describe amplitude shift keying (ASK) modulation with suitable circuit diagram.

Answer : Explanation:- ASK MODULATOR: The process where a binary information signal directly modulates the amplitude of an analog carrier. The digital signal is used to switch the carrier between amplitude levels is ... Block diagram of ASK Transmitter / ASK modulator:-  Waveforms:- 

Description : Define stub. Explain single and double stub in brief with neat sketch.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Description : Explain duct propagation with neat sketch.

Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

Description : Define and explain the term beam width related to antenna with a sketch.

Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Description : Explain operation of balanced slope detector with „s‟ curve.

Answer : Diagram: Explanation:   Curve:  

← Prev Question Next Question →
editChoose topic
...