State the need of AGC. List the different types of AGC with neat graph.

1 Answer

Need of AGC:- The need or purpose of AGC circuit is to maintain the output voltage level (volume) of radio receiver constant over a wide range of RF input signal level.  AGC also helps to smooth out the rapid fading which may occur with long distance short wave reception & prevents overloading of the last IF amplifier which might otherwise have occurred 

Types of AGC:-

1) Simple AGC

2) Delayed AGC

Graphical representation of AGC:- 

image

Like 0 like Dislike 0 dislike

Related questions

Description : State the need of AGC.

Answer : Need of AGC:- The need or purpose of AGC circuit is to maintain the output voltage level (volume) of radio receiver constant over a wide range of RF input signal level. AGC ... long distance short wave reception & prevents overloading of the last IF amplifier which might otherwise have occurred 

Description : Explain simple AGC and delayed AGC with the help of neat graph.

Answer : 1) Simple AGC:- Simple AGC is a system by means of which overall gain of a radio receiver is varied, automatically with the changing strength of the receiver signal to keep the ... not used in low cost radio receiver. It is used in high quality receiver like communication receiver.

Description : Define sensitivity with graph.

Answer : Define sensitivity with graph.

Description : State the need for filters and list the different types of filters.

Answer : Need for filters 1) Output of all rectifiers is pulsating dc voltage and most of citcuits which work on dc requires pure dc voltage. 2) So in order to get pure dc waveform, filters are connected at the ... 2) Choke input filter(series inductor filter) 3) LC filter 4) π Filter 5) RC filter

Description : What are the different types of FM detector?

Answer : The different types of FM Detectors are: 1. Simple Slope Detector 2. Balanced Slope Detector 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL) 

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Description : List the types of FM detector. Explain any one of them.

Answer : Types of FM detector:- 1. Simple slope detector 2. Balanced slope detector 3. Phase discriminator(Foster seely discriminator) 4. Ratio detector 5. PLL detector Simple ... . If the IF amplitude is sufficiently limited prior to reaching the PLL and the loop is properly compensated 

Description : List the types of micro-strip antennas. Explain any one of them.

Answer : List the types of micro-strip antennas are as fallows. 1) RECTANGULER 2) CIRCULER. 3) SQUARE . 4) ELIPTICAL. 5) TRINGULAR. Rectangular Micro-strip Antenna: Micro-strip ... mobile phone market. Patch antennas are low cost, have a low profile and are easily fabricated. 

Description : List the types of noise in communication system. Explain any one of them.

Answer : Explanation of External Noise:- Atmospheric Noise:- Atmospheric noise or static is caused by lighting discharges in thunderstorms and other natural electrical disturbances occurring in the atmosphere ... between two or more paths, and results from the random fluctuations in the division. 

Description : State the need of stub. Explain single stub and double stub matching.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

Description : State the need of modulation.

Answer : Need of Modulation :- i)Reduction in the height of antenna  ii) Avoids mixing of signal  iii) Increases range of communication.  iv) Multiplexing is possible v) Improve quality of reception.

Description : State the types of electromagnetic polarization? Define any one of it.

Answer : Transverse electromagnetic wave:- The polarization of a plane EM wave is simply the orientation of the electric field vector with respect to the surface (i.e. looking at the horizon) If ... the field strength varies with change in polarization the wave is said to have an elliptical polarization 

Description : State the process FM detection? State it‟s any two types.

Answer : FM detection: In any radio that is designed to receive frequency modulated signals there is some form of FM demodulator or detector. This circuit takes in frequency modulated RF signals and takes the ... 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL)

Description : State and explain the types of noise in communication system.

Answer : External Noise:  Atmospheric Noise  Atmospheric noise or static is caused by lighting discharges in thunderstorms and other natural electrical disturbances occurring in the atmosphere. These ... between two or more paths, and results from the random fluctuations in the division.

Description : Define pulse modulation. State its types. 

Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Description : Explain duct propagation with neat sketch.

Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

Description : Explain “BALUN” with neat sketch

Answer : Diagram- Explaination

Description : Explain virtual height with respect to wave propagation with neat sketch.

Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

Description : Explain isotropic radiator with neat sketch. 

Answer : An isotropic radiator is a point source that radiates equally in all the directions. It is a hypothetical antenna used as a reference to describe real antenna. The radiation is represented by a sphere with center coincides with location of isotropic radiator.

Description : Explain ground wave propogation with neat sketch. 

Answer : Sketch-   Explanationi) It consists of direct wave which travels near the ground from Transmitter to Receiver. ii) The electromagnetic wave leaves the transmitting antenna & remains close to earth surface ... . The ground wave is the path chosen when frequency in between 30 KHz & 3 MHz 

Description : Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Answer : With diode D2 reversed , O is positive with respect to b, so that Vab is a sum voltage rather than the difference it was in the discriminator it is now possible to connect a large capacitor ... of limiter stage due to large capacitor C5 .Hence, limiter stage is not used in ratio detector.  

Description : With the help of neat diagram, explain the working of phase discriminator.

Answer : Explanation:- This discriminator is also known as the center tuned discriminator or the Foster Seeley discriminator after its inventors. It is possible to obtain the same S- Shape response curve from a circuit in ... fin = fc, fin > fc + Δf and fin<fc- Δf should be given marks

Description : Define stub. Explain single and double stub in brief with neat sketch.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Description : Describe ionosphere with neat sketch.

Answer : The Ionosphere is the upper portion of the atmosphere. The ultra violet radiation from the sun will ionize the upper layer of the atmosphere. Due to ionization these part of the atmosphere becom3es ... electron density of all layers, due to this F2 layer remains present at night time  

Description : Explain effect of 'm' on AM with neat waveforms.

Answer : i)m< 1  If m < 1 or if the percentage of modulation is less than 100% the this type of modulation is known as under modulation The amplitude of modulating signal less than carrier ... greater amplitude part of its information is lost in the process of modulation which is undesirable.

Description : Explain skip zone and skip distance with neat diagram.

Answer : Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wav of fixed frequency returns back to the earth. Skip zone: skip zone where signal is not detectable

Description : Explain any four different frequency bands and give their two applications of each.

Answer : Explain any four different frequency bands and give their two applications of each.

Description : Write down different frequencies for following(frequency ranges). (1) Voice frequency (2) High frequency (3) IR frequency (4) Visible frequency(light)

Answer : Sr. No Frequency Range 1 Voice Frequency 300 Hz to 3kHz 2 High Frequency  3 MHz to 30 MHz 3 IR Frequency 30 THz to 430 THz 4 Visible Spectrum (light) 375 THz to 750 THz

Description : State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type. 

Answer : Need of multistage amplifier: The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, ... use more than one stage of amplification. Such an amplifier is called a MULTISTAGE AMPLIFIER .

Description : Define fading? List the causes.

Answer : The fluctuation in signal strength at a receiver, which is mainly due to the interference of two waves which left the same source but arrived at the destination by different paths, is known ... , such as irrigation, or from multiple transmission paths, irregular earth surfaces, and varying terrains.

Description : List and explain the properties of quarter wave transformer.

Answer : Properties of quarter wave transformer: 1. Impedance transfomation: it provides impedance transformation upto the highest frequencies and is compatible with transmission line. 2. Impedance inversion: if ZL is ... or step up transformer,depending on whether ZL IS greater than or less than ZO.

Description : Draw the block diagram of PWM. List its advantages 

Answer : Block diagram of PWM:- Advantages of PWM:- 1. More immune to noise. 2. Synchronization between transmitter and receiver is not required. 3. Possible to separate out signal from noise.

Description : Draw the structure of horn antenna and its radiation pattern. List its any two applications.

Answer : The structure of horn antenna Radiation pattern of Horn Antenna Application:- i) Used at microwave frequency. ii) Used in satellite tracking 

Description : State the different types of SI engine combustion chambers. Draw a neat sketch of any one.

Answer : 1) T Head Type Combustion chambers 2) L Head Type Combustion chambers 3) F- Head combustion chamber 4) Over head valve or I head combustion chamber 5) Hemispherical combustion chamber 6) Bathtub ... - Head combustion chamber 4) Over head valve or I head combustion chamber

Description : List different types of capacitors? State the dielectric materials used for it.

Answer : Types of capacitors: 1. Electrolytic capacitor 2. Variable capacitor 3. Air ganged capacitor 4. PVC ganged capacitor 5. Trimmer capacitor Dielectric materials used in capacitors: 1. Air 2. ... Ceramic 5. Porcelain 6. Polystyrene. 7. Fibre 8. Bakelite 9. Waxed paper 10.Plastic

Description : State the necessity of Balancing. List different types of Balancing Methods. 

Answer : Necessity of Balancing: [1] The high speed of engines and other machines is a common phenomenon now-adays. It is, therefore, very essential that all the rotating and reciprocating parts should be ... masses rotating in the different planes [2] Balancing of Several masses revolving in same plane: 

Description : State the purpose of lighting control. List the different types of dimmer.

Answer : Purpose of Lighting Control:- 1. To turn ON or OFF the lamps 2. For dimming: The dimming control permits the adjustment of lighting over a range. 3. For changing the lighting levels ... operated dimmer 6) Triac operated Dimmer 7) PWM (Pulse width modulation) Controlled technique.

Description : List different types of stepper motor. State one application of stepper motor.

Answer : Types of stepper motor : (i)Variable - reluctance motor (ii) Permanent- magnet motors (iii) Hybrid motors. Applications of stepper motor : In robotics, In CNC machines, In computers, printers, ... In Watches, In biomedical applications such as X-ray machines, CT scan, In Process control systems. 

Description : List different types of signals. State application of each.

Answer : Different Types of Signals: 1) Flag signals: This is shown by signalman if green flag is raised; it means to proceed with caution. Green flag shown down, it means there is track defect; ... green lamps indicate indications as in the 2-aspect system, and the yellow lamp shows the caution indication.

Description : State the function of a contactor in a power circuit of locomotive. List different types of it and state one application of each.

Answer : Ans: Contactor in power circuit of locomotive is used to connect relevant sections for operation. Connecting or disconnecting the power circuit at different conditions of operation and at different locations. ... heavy power currents. 3) Cam & roller operated - used for group switching.

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

Description : State and explain the concept of transmission bandwidth.

Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Description : State the IF frequency and bandwidth of FM receiver.

Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

Description : Define modulation? State the desirable value of modulation index of AM.

Answer : Modulation: It is the process in which any of these Parameters (Amplitude, Frequency, Phase) of high frequency signal (carrier signal) are varied in accordance with low frequency signal(modulating signal) For an AM, modulation index range is 0 to 1.

Description : State the frequency range for audio frequency and voice frequency.

Answer : The generally accepted standard range of audible frequencies is 20 to 20,000 Hz, The usable voice frequency band ranges from approximately 300 Hz to 3400 Hz.

Description : State and explain concept of bandwidth.

Answer : 1. Bandwidth is defined as a range within a band of frequencies or wavelengths. ... For digital devices, the bandwidth is usually expressed in bits per second (bps) or bytes per second. For analog devices, the bandwidth ... or Hertz (Hz) 2.Suppose the frequency range is f1 to f2 , then B.W= f2 - f1

Description : Draw the circuit diagram of PWM using IC555. State its operation.

Answer : Operation: i. The timer IC555 is operated in monostable mode. ii. The negative going carrier pulses are to the differentiator formed by R1 & C1. The differentiator produces sharp negative ... . Thus PWM signal is generated at the output pin (3) of IC555 as monostablemultivibrator. 

Description : Draw block diagram of basic electronic communication system and state the function of each block.

Answer : i) Input signal: - The information can be in the form of sound, picture or data coming from computer. ii) Input transducer: - it converts original information into equivalent electrical ... back to suitable form. vii) Output transducer: - It converts electrical signal into original form. 

← Prev Question Next Question →
Ask a Question
Choose topic