Define the term baluns and explain where is it used?

1 Answer

A type of electrical transformer used to connect an unbalanced circuit to a balanced oneORA balun is a type of transformer: it's used to convert an unbalanced signal to a balanced one or vice versa. Application:- In audio applications, baluns convert between high-impedance unbalanced and low impedance balanced lines.
Like 0 like Dislike 0 dislike

Related questions

Description : Explain the use of baluns for impedance matching.

Answer : Balun stands for Balance to unbalance. It can also be used to connect the unbalanced transmission line to a balance load such as antenna. It consist of special type of transformer with an unbalanced primary ... matching. Its input is 300-75ohm. It consist of two quarter wave length.  

Description : Define and explain the term beam width related to antenna with a sketch.

Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Description : Define stub. Explain single and double stub in brief with neat sketch.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Description : Define the transmission line? Draw it‟s general equivalent circuit.

Answer : Transmission line: A conductor or conductors designed to carry electricity or an electrical signal over large distances with minimum losses and distortion.  Equivalent circuit:

Description : State the types of electromagnetic polarization? Define any one of it.

Answer : Transverse electromagnetic wave:- The polarization of a plane EM wave is simply the orientation of the electric field vector with respect to the surface (i.e. looking at the horizon) If ... the field strength varies with change in polarization the wave is said to have an elliptical polarization 

Description : Describe the term virtual height with the help of diagram showing ionized layer and the path of wave.

Answer : Virtual height: -The incident wave returns back to the earth due to refraction. In this process it bends down gradually and not sharply, but the incident and reflected rays follow exactly ... . It is also defined as the maximum height that the hypothetical reflected wave would have reached. 

Description : Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Answer : With diode D2 reversed , O is positive with respect to b, so that Vab is a sum voltage rather than the difference it was in the discriminator it is now possible to connect a large capacitor ... of limiter stage due to large capacitor C5 .Hence, limiter stage is not used in ratio detector.  

Description : Define PAM, PWM, and PPM. Draw waveforms.

Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Description : Define electromagnetic wave and polarization.

Answer : Electromagnetic wave:-An electromagnetic wave such as light consists of a coupled oscillating electric field and magnetic field which are always perpendicular; by convention Polarization:-polarization" of electromagnetic waves refers to the direction of the electric field.

Description : Define selectivity and sensitivity of AM Receiver. 

Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Description : Define: (i) Image frequency and (ii) Double spotting

Answer : i)Image frequency:- Image Frequency is defined as the signal frequency plus twice the intermediate frequency. It is denoted as fsi = fs+2fi Where, fs = Signal Frequency fi =intermediate frequency ... It is due to the poor front end selectivity i.e., inadequate image frequency rejection.

Description : Define modulation index in AM and give its formula.

Answer : In AM wave, the modulation index (m) is defined as the ratio of the amplitude of the modulating signal (Vm ) to the amplitude of carrier signal (Vc). m = Vm / Vc

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Description : Define critical frequency w.r. to wave propagation.

Answer : Define critical frequency w.r. to wave propagation.

Description : Define VSWR with refernce to standing waves.

Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

Description : Define sensitivity with graph.

Answer : Define sensitivity with graph.

Description : Define: 1)Frequency 2)Bandwidth 3)Wavelength 4)Time period

Answer : Frequency: Frequency is the number of cycles per second. Bandwidth: A range of frequencies within a given band, in particular that used for transmitting a signal. Wavelength: Wavelength can be defined as ... for one complete cycle of vibration to pass a given point.  OR Time period=1/frequency

Description : Define modulation? State the desirable value of modulation index of AM.

Answer : Modulation: It is the process in which any of these Parameters (Amplitude, Frequency, Phase) of high frequency signal (carrier signal) are varied in accordance with low frequency signal(modulating signal) For an AM, modulation index range is 0 to 1.

Description : Define fading? List the causes.

Answer : The fluctuation in signal strength at a receiver, which is mainly due to the interference of two waves which left the same source but arrived at the destination by different paths, is known ... , such as irrigation, or from multiple transmission paths, irregular earth surfaces, and varying terrains.

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

Description : Define pulse modulation. State its types. 

Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

Description : Define the following terms: (i) Polarization (ii) Antenna gain (iii)Antenna resistance (iv)Directivity

Answer : i) Polarization:- It is defined as the direction of electric field vector in the EM wave radiated by the transmitting antenna. ii) Antenna Gain:- Antenna gain is defined as the ratio of ... in only one direction in which the radiation is maximum. That is directivity = Max. directive gain

Description : Define the terms: 1) Maximum usable frequency 2) Fading

Answer : 1)Maximum usable frequency:- Maximum usable frequency is defined as the limiting frequency ,when the angle of incidence is other than the normal . OR The highest frequency that can be used for sky ... which left the same source but arrived at the destination by different paths is known as fading.

Description : Define standing wave ratio. 

Answer : Standing wave ratio is defined as the ratio of maximum voltage (Vmax) to minimum voltage (Vmin). Standing wave ratio is also defined as the ratio of maximum current (Imax) to minimum current (Imin).

Description : Define: Base band signal with one example.

Answer : The electrical equivalent of the original information signal is known as the Baseband signal. Example:-The information or the input signal to a communication system can be analog i.e., sound, picture or it can be digital e.g. the computer data.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Description : State the need of stub. Explain single stub and double stub matching.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

Description : State and explain the concept of transmission bandwidth.

Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Description : Explain working of envelope detector with suitable diagram and waveform.

Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

Description : Draw construction of Yagi-Uda antenna and explain.

Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

Description : Draw and explain block diagram of electronic communication system.

Answer : Block diagram of electronic communication system. Explanation Transducer: A transducer is usually required to convert the output of a source into an electrical signal that is suitable for ... etc. Output Transducer: The output transducer converts electrical signal in to sound signal.  

Description : Explain how modulation reduces height of antenna and avoid mixing of signals.

Answer : Modulation reduces antenna height: For the transmission of radio signals, the antenna height must be multiple of λ/4 ,where λ is the wavelength . λ = c /f where c : is the ... will occupy different slots in the frequency domain (different channels). Thus, modulation avoids mixing of signals.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Description : Draw and explain PLL as an FM demodulator.

Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Description : Explain skip zone and skip distance with neat diagram.

Answer : Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wav of fixed frequency returns back to the earth. Skip zone: skip zone where signal is not detectable

Description : Explain any four different frequency bands and give their two applications of each.

Answer : Explain any four different frequency bands and give their two applications of each.

Description : State and explain concept of bandwidth.

Answer : 1. Bandwidth is defined as a range within a band of frequencies or wavelengths. ... For digital devices, the bandwidth is usually expressed in bits per second (bps) or bytes per second. For analog devices, the bandwidth ... or Hertz (Hz) 2.Suppose the frequency range is f1 to f2 , then B.W= f2 - f1

Description : Draw the circuit diagram of practical diode detector and explain its working. 

Answer : Circuit diagram of practical diode detector:  Explanation- The circuit operates in the following manner- The diode has been reversed so that now the negative envelope is demodulated. Due to this ... to produce AGC voltage. The DC AGC voltage is proportional to the amplitude of AM signal. 

Description : State and explain the types of noise in communication system.

Answer : External Noise:  Atmospheric Noise  Atmospheric noise or static is caused by lighting discharges in thunderstorms and other natural electrical disturbances occurring in the atmosphere. These ... between two or more paths, and results from the random fluctuations in the division.

Description : Explain standing waves with load terminal open circuited and short circuited. 

Answer : Standing waves with load terminal open circuited   Standing waves: The forward and reflected waves on the incorrectly terminated transmission line produce an interference pattern known as Standing ... , the load impedance will not be equal to the transmission line (characteristic)impedence.

Description : Draw the circuit diagram of limiter and explain its working.

Answer : Circuit diagram of amplitude limiter:- Explanation:- 1. In frequency modulation, the signal amplitude is held constant while the carrier frequency is varied. 2. Any noise that contaminates ... V p-p instead of the alternately driven into saturation and cutoff, it limits the signal amplitude

Description : Draw the TRF receiver block diagram and explain its working. 

Answer : Explanation:- 1. TRF receivers are simple and having high sensitivity. The AM transmission takes place in MW band and SW band. MW frequency range is 540KHz to 1640KHz. 2. ... power level to drive the loudspeaker. 7. The loudspeaker converts electrical signal into original sound information.

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Description : List and explain the properties of quarter wave transformer.

Answer : Properties of quarter wave transformer: 1. Impedance transfomation: it provides impedance transformation upto the highest frequencies and is compatible with transmission line. 2. Impedance inversion: if ZL is ... or step up transformer,depending on whether ZL IS greater than or less than ZO.

Description : Explain pre-emphasis and de-emphasis concept in FM.

Answer : Pre-emphasis:- In an FM system the higher frequencies contribute more to the noise than the lower frequencies. Because of this all FM systems adopt a system of pre-emphasis where the higher frequencies are ... at receiver to improve the noise immunity Pre-emphasis/ De-emphasis graph:

Description : State and explain the losses in transmission line.

Answer : Losses in Transmission Line:- There are three ways in which energy, applied to a transmission may desperate before reaching the load. They are 1) Radiation Losses:- Its occurs when a ... down voltage of the dielectric insulator. Generally when corona occurs, the transmission line is destroyed.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Answer : Solution :

Description : How quarter wave transformer is used for impedance matching. 

Answer : In all applications of transmission line, it is required that the load be matched to line, Which requires tuning out the unwanted load reactance and the transformation of resulting impedance to the required value ... Step down transformer If ZL <Zo then it acts as a Step up transformer  

← Prev Question Next Question →
Ask a Question
Choose topic