Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

1 Answer

Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.


thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Compare ground wave propagation. Sky wave propagation and space wave propagation.

Answer : Sr. N o Parameter Ground Wave Propagation Sky Wave Propagation Space wave Propagation 1 Frequency Range 30 kHz to 3 MHz  3 MHz to 30 MHz frequencies above 30 MHz 2 ... These waves have line of sight propagation, ... 6 Fading Problem less Severe Less

Description : Compare sky wave and space wave propagation w.r.t. following points. (i) Frequency range (ii) Effect of fading (iii)Polarization (iv)Application

Answer : Sr. No  Parameters Sky Wave Propagation Space Wave Propagation 1 Frequency range 3 MHz to 30 MHz  Above 30 MHz 2 Effect of fading Problem of fading is ... horizontally Polarized 4 Application RadioBroadcasting (SW Range) Used for TV and FM broadcasting

Description : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Answer : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Description : Define critical frequency w.r. to wave propagation.

Answer : Define critical frequency w.r. to wave propagation.

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Description : Describe the effect of ionosphere on sky wave propagation.

Answer : The Ionosphere is the upper portion of the atmosphere. The ultra violet radiation from the sun will ionize the upper layer of the atmosphere. In this layer free electrons and positive and negative ions are ... layer. Its Frequency Range is from 3 MHz to 30 MHz Polarization: Vertical.  

Description : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Answer : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Description : Compare series and parallel resonance on the basis of (i) Resonating frequency (ii) Impedance (iii) Current (iv) Magnification

Answer : S. No . Parameter Series Circuit Parallel Circuit 1 Resonating frequency 2 Impedance Minimum, Z = R Maximum, Z = L/CR 3 Current Maximum, I ... , I = V/(L/CR)  4 Magnification Voltage magnification takes place Current magnification takes place

Description : Explain virtual height with respect to wave propagation with neat sketch.

Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

Description : Explain the transverse electromagnetic waves in wave propagation.

Answer : 1. The electromagnetic waves are oscillations, which propagate through free space. 2. Em wave travel in free space at the speed of light. 3. Figure shows the simple EM wave, in which the direction of ... electromagnetic waves (TEM). Diagram:- Transverse electromagnetic wave(TEM) OR

Description : Explain the following in wave propagation: 1) Actual height 2) Virtual height

Answer : 1) Actual height:- The height attained by the wave during propagation through the ionosphere is known as Actual height. 2)Virtual height: -The incident wave returns back to the earth due to ... It is also defined as the maximum height that the hypothetical reflected wave would have reached.

Description : Draw the radiation pattern for Dipole antenna: (i) Half wave dipole (ii) Folded dipole.

Answer : The radiation pattern for Half wave dipole antenna The radiation pattern for Folded dipole antenna.

Description : Define: (i) Image frequency and (ii) Double spotting

Answer : i)Image frequency:- Image Frequency is defined as the signal frequency plus twice the intermediate frequency. It is denoted as fsi = fs+2fi Where, fs = Signal Frequency fi =intermediate frequency ... It is due to the poor front end selectivity i.e., inadequate image frequency rejection.

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Description : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Answer : A telephone cable has following primary constants per loop kilometer ,R=30Ω, L=20mH,C=0.06µF,G=0.If the applied signal has an angular frequency of 5000 rad/sec.., Determine (i) Characteristics impedence (ii) Attenuation constant

Description : Explain ground wave propogation with neat sketch. 

Answer : Sketch-   Explanationi) It consists of direct wave which travels near the ground from Transmitter to Receiver. ii) The electromagnetic wave leaves the transmitting antenna & remains close to earth surface ... . The ground wave is the path chosen when frequency in between 30 KHz & 3 MHz 

Description : Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Answer : Sr. No Parameters Narrow band FM Wide band FM 1 Modulation index Less than or slightly greater than 1 Greater than 1  2 Maximum deviation ... like police wireless, ambulance etc. Entertainment broadcasting can be used for high quality music transmission 

Description : State the frequency range for audio frequency and voice frequency.

Answer : The generally accepted standard range of audible frequencies is 20 to 20,000 Hz, The usable voice frequency band ranges from approximately 300 Hz to 3400 Hz.

Description : Show that AM wave consist of two side bands and carrier. Also prove the bandwidth of AM is double of the modulating frequency.

Description : Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size 

Answer : Comparison between detonation and diesel knock: Parameter To avoid Detonation in SI Engine  To avoid Diesel knock i) Fuel Ignition Temperature High Low ii) Compression Ratio ... Cylinder wall temperature Low High viii) Cylinder size Small Large

Description : Compare floor inspection and centralized inspection on the basis of (i) Definition. (ii) Measuring instruments used (iii) Suitability. (iv) Mode of inspection.

Answer : Parameters Floor Inspection Centralized Inspection Definition. Inspection is done at the place where the part is made or assembled is called floor inspection. The inspection is done ... Mode of inspection. Online inspection is possible Offline inspection needs to be done.

Description : Compare Brazing and Soldering on the basis of : (i) Temperature Used. (ii) Filler Material. (iii) Joint Strength (iv) Applications.

Answer : Comparison of Brazing and Soldering:

Description : Compare the SI and CI engine on the basis of: (i) Compression Ratio (ii) Operating Speed (iii) Power O/P per weight.

Answer : Parameter SI Engine CI Engine (i) Compression Ratio Compression ratio is low, about 10:1 limited by detonation Compression ratio is higher, about 18:1 to 22:1 (ii) ... due to lower compression ratio. Power output is more than SI engine due to higher compression ratio.

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Answer : Parameter Class A Class B 

Description : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Answer : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Description : Compare CC and PC of wattmeter on the basis of:- (i) Connection (ii) Status (iii) Number of turns (iv) Gauge of wire.

Answer : Particulars Current coil (CC) Pressure coil (PC) Connection Connected in series with load Connected in parallel with load Status It is fixed coil in wattmeter It is moving coil in ... number of turns It is having more number of turns Gauge of wire Less More

Description : Compare between BJT and FET on the basis of (i) Biolar/Unipolar (ii) Tharmal Runaway (iii) Noise (iv) Applications

Answer : Parameter BJT FET Bipolar/Unipolar It is bipolar device i.e. current in this device is carried by electrons and holes. It is unipolar device i.e. current ... in oscilloscopes, electronic voltmeters and other measuring and testing equipment because of their high input impedance.

Description : Compare indoor and outdoor sub-station on given points : (i) Capital cost (ii) Time required for completion (iii) Availability of natural light (iv) Space required 

Answer : Sr. No.  Points Indoor substation Outdoor substation  1 Capital cost High, as construction work cost is more.  Less, as construction work cost is less 2 Time required for ... time. So it saves electrical energy & its cost 4 Space Require Less More

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

Description : The VLF and LF bauds use .............. propagation for communication. (A) Ground (B) Sky (C) Line of sight (D) Space

Answer : Answer: A Explanation: VLF (Very Low Frequency) LF (Low Frequency) In general there are three type of propagation.1.Ground Propagation 2.Sky propagation 3.Line-of-sight propagation ... portion of the atmosphere. These low-frequency signals travel in all directions from the transmitting antenna.

Description : Compare RTD and thermistor on the basis of temperature coefficient , linearity, temperature range and cost.

Answer : Parameters RTD Thermistors Temperature coefficient  It has positive temperature Coefficient (PTC) of Resistance. It has both positive and negative temperature Coefficient (PTC and NTC) of Resistance. ... -270oC to 2800oC -150oC to 300oC Cost High cost Low cost

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

Description : a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Answer : reflection coefficient R=Vr/Vi i. There is no reflected voltage. i.e,Vr=0 R=0 SWR= 1+R/1-R=1 ii. Reflected voltage and incident voltage is equal. Vr=Vi; R=1 SWR= 1+R/1-R=1+1/1-1=infinity iii. If reflected ... and incident voltage =20V. Vr=10 and Vi=20 R=10/20=0.5 SWR= 1+R/1-R=1+.5/1-.5=3 

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Description : For a transmission line, the incident voltage. Ei = 6V and Er =2V ,Calculate: (i) Reflection Coefficient (ii) SWR

Answer : Reflection Coefficient(K) = Er / Ei  = 2V / 6V  K = 0.333 SWR = 1+K / 1- K  = 1+0.333 / 1-0.333  = 1.333 / 0.667 SWR= 1.998

Description : Explain duct propagation with neat sketch.

Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

Description : Describe line of sight propagation in brief.

Answer : Line of sight propagation or Space wave propagation:-   Explanation:- Space wave propagation of electromagnetic energy includes radiated energy that travels in the lower few miles of Earth's ... waves reflected by Earth's surface as they propagate between the transmit and receive antennas. 

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Description : Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna 

Answer : i. Rectangular antenna is used in direction finding in portable recievers. ii. Dish antenna is used to transmit and receive signal from satellite. iii. Yagi-Uda antenna is used in HF and VHF range as a TV receiving antenna. iv. Horn antenna is used in satellite tracking.

Description : Draw radiation pattern for following antenna i) Yagi-Uda antenna ii) Loop antenna iii) Dish antenna iv) Horn antenna

Answer : Type of antenna Radiation Patteren  Yagi-Uda antenna Loop antenna Dish antenna Horn antenna 

Description : Describe with respect to antenna (i) radiation pattern (ii) directive gain (iii) power gam (iv) polarization

Answer : (i) Radiation pattern:-A graph or diagram which tells us about the manner in which an antenna radiates more power in different directions is known as the radiation patteren of antenna.  ( ... as the direction of the electric vector in the electromagnetic wave radiated by the transmitting antenna. 

Description : Define the following terms: (i) Polarization (ii) Antenna gain (iii)Antenna resistance (iv)Directivity

Answer : i) Polarization:- It is defined as the direction of electric field vector in the EM wave radiated by the transmitting antenna. ii) Antenna Gain:- Antenna gain is defined as the ratio of ... in only one direction in which the radiation is maximum. That is directivity = Max. directive gain

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Answer : The polarization required in ground wave propagation is vertical (linear).

Description : A 400 W carrier is amplitude modulated to a depth of 75%.Calculate the total power in AM wave. (i) Explain the types of noise in a communication system. (ii) Compare simplex and duplex mode of communication.

Answer : (i) Noise: Noise is any spurious or undesired disturbances that mask the received signal in a communication system. a) Atmospheric Noise: Atmospheric Noise is also known as static noise which is the ... remote control ExamplesWalkytalky,telephone,mobile,Radar, FAX,Pager 4

Description : Compare TRF and super heterodyne receivers.

Answer : Compare TRF and super heterodyne receivers. 

Description : Compare resonant and non-resonant antennas.

Answer : Distinguish between resonant and non-resonant antennas.

Description : Compare between FM and PM 

Answer : PARAMETERS FM PM 1. Variable parameter of carrier. Frequency Phase 2. Variable parameter proportional to modulating voltage.  Frequency deviation Phase deviation.  3. Amplitude ... for transmitted power More Moderate 6. Signal to noise ratio Best Better

Description : Compare between simplex and duplex communication 

Answer : simplex and duplex communication :

← Prev Question Next Question →
editChoose topic