Define modulation index in FM. What is maximum value of deviation ratio.

1 Answer

Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm).

(OR)

image  

Like 0 like Dislike 0 dislike

Related questions

Description : Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Answer : Sr. No Parameters Narrow band FM Wide band FM 1 Modulation index Less than or slightly greater than 1 Greater than 1  2 Maximum deviation ... like police wireless, ambulance etc. Entertainment broadcasting can be used for high quality music transmission 

Description : Define modulation? State the desirable value of modulation index of AM.

Answer : Modulation: It is the process in which any of these Parameters (Amplitude, Frequency, Phase) of high frequency signal (carrier signal) are varied in accordance with low frequency signal(modulating signal) For an AM, modulation index range is 0 to 1.

Description : Give the expression for modulation index for AM and FM.

Answer : 1.Modulation index for AM ma=Vm / Vc Where Vm is modulating voltage Vc is the carrier voltage 2.Modulation index for FM mf=δ /fm where δ is the deviation fm is the modulating frequency

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Description : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -  a) 2 b) 5 c) 3 d) 4

Answer : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: - 5

Description : Define modulation index in AM and give its formula.

Answer : In AM wave, the modulation index (m) is defined as the ratio of the amplitude of the modulating signal (Vm ) to the amplitude of carrier signal (Vc). m = Vm / Vc

Description : Define modulation index of FM.

Answer : Modulation index of FM is defined as the ratio of the frequency deviation to the modulating frequency.

Description : Define pulse modulation. State its types. 

Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Description : Compare AM with FM with respect to following points: a) Definition. b) Modulation index. c) Bandwidth. d) Side band.

Answer : Parameters AM FM Definition It is the process in which the amplitude of carrier signal is varied in accordance with the instantaneous value of modulating signal keeping frequency and ... frequency deviation. Side band There are two sidebands Infinite number of sideband

Description : An FM signal with modulation index mƒ is passed through a frequency tripler. The modulation index of the output signal will be (1) mƒ (2) 3mƒ (3) 9mƒ (4) 27mƒ

Answer : An FM signal with modulation index mƒ is passed through a frequency tripler. The modulation index of the output signal will be 3mƒ

Description : In commercial FM broadcasting, the maximum frequency deviation is normally   (A) 5 KHz (B) 15 KHz (C) 75 KHz (D) 200 KHz

Answer : In commercial FM broadcasting, the maximum frequency deviation is normally 75 KHz

Description : What are the different types of FM detector?

Answer : The different types of FM Detectors are: 1. Simple Slope Detector 2. Balanced Slope Detector 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL) 

Description : Define the terms: 1) Maximum usable frequency 2) Fading

Answer : 1)Maximum usable frequency:- Maximum usable frequency is defined as the limiting frequency ,when the angle of incidence is other than the normal . OR The highest frequency that can be used for sky ... which left the same source but arrived at the destination by different paths is known as fading.

Description : Define standing wave ratio. 

Answer : Standing wave ratio is defined as the ratio of maximum voltage (Vmax) to minimum voltage (Vmin). Standing wave ratio is also defined as the ratio of maximum current (Imax) to minimum current (Imin).

Description : Explain the working of amplitude limiter in FM receiver with circuit diagram.

Answer : Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy  Circuit Diagram:

Description : Explain pre-emphasis and de-emphasis concept in FM.

Answer : Pre-emphasis:- In an FM system the higher frequencies contribute more to the noise than the lower frequencies. Because of this all FM systems adopt a system of pre-emphasis where the higher frequencies are ... at receiver to improve the noise immunity Pre-emphasis/ De-emphasis graph:

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Description : State the process FM detection? State it‟s any two types.

Answer : FM detection: In any radio that is designed to receive frequency modulated signals there is some form of FM demodulator or detector. This circuit takes in frequency modulated RF signals and takes the ... 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL)

Description : State the IF frequency and bandwidth of FM receiver.

Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

Description : Describe the block diagram of FM superhetrodyne receiver

Answer : RF amplifier:- There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM broadcast the ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Description : Explain with block diagram of Armstrong method of FM generation.

Answer : Explanation:- The crystal oscillator generates the carrier at low frequency typically at 1 MHz this is applied to the combining network and a 90o phase shifter. The modulating signal is passed through an ... power amplifier to raise the power level of the FM signal.  Phasor Diagram:-   

Description : Draw and explain PLL as an FM demodulator.

Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Description : Explain reactance modulator for FM generation.

Answer : Explanation :- Audio modulating signal is applied to Q1 which varies the base voltage and current of Q1 according to the input information to be transmitted. The collector current ... lower the frequency & decrease capacitance increase the frequency and thus produce direct FM at output.

Description : List the types of FM detector. Explain any one of them.

Answer : Types of FM detector:- 1. Simple slope detector 2. Balanced slope detector 3. Phase discriminator(Foster seely discriminator) 4. Ratio detector 5. PLL detector Simple ... . If the IF amplitude is sufficiently limited prior to reaching the PLL and the loop is properly compensated 

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Answer : block diagram of FM super heterodyne radio receiver

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Description : Compare between FM and PM 

Answer : PARAMETERS FM PM 1. Variable parameter of carrier. Frequency Phase 2. Variable parameter proportional to modulating voltage.  Frequency deviation Phase deviation.  3. Amplitude ... for transmitted power More Moderate 6. Signal to noise ratio Best Better

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Description : Explain how modulation reduces height of antenna and avoid mixing of signals.

Answer : Modulation reduces antenna height: For the transmission of radio signals, the antenna height must be multiple of λ/4 ,where λ is the wavelength . λ = c /f where c : is the ... will occupy different slots in the frequency domain (different channels). Thus, modulation avoids mixing of signals.

Description : State the need of modulation.

Answer : Need of Modulation :- i)Reduction in the height of antenna  ii) Avoids mixing of signal  iii) Increases range of communication.  iv) Multiplexing is possible v) Improve quality of reception.

Description : If modulation index is 0.6, maximum power efficiency (in %) of AM is about  A) 60 B) 30 C) 20 D) 10

Description : The ratio of maximum displacement deviation to full scale deviation of the instrument is called?

Answer : The ratio of maximum displacement deviation to full scale deviation of the instrument is called linearity.

Description : Write the IF value of (i) FM ratio recevier. (ii) MW band AM.

Answer : (i) 10.7 Mhz (ii) 455 Khz

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Description : Draw and label the circuit diagram of ratio detector 

Answer : Draw and label the circuit diagram of ratio detector  

Description : Explain with a neat diagram of ratio detector. Why limiter stage is not used before ratio detector.

Answer : With diode D2 reversed , O is positive with respect to b, so that Vab is a sum voltage rather than the difference it was in the discriminator it is now possible to connect a large capacitor ... of limiter stage due to large capacitor C5 .Hence, limiter stage is not used in ratio detector.  

Description : For transmission line, the incident voltage Ei = 6V, and Er = 3V. Calculate: (1) Reflection coefficient (2) Standing wave ratio

Answer : (1)Reflection coefficient  (2) Standing wave ratio (1)Reflection coefficient Reflection coefficient R=Er/Ei  =3/6  R=0.5 (2) Standing wave ratio SWR=Ei+Er/Ei-Er  =6+3/6-3  SWR =3

Description : For FM signal, the frequency deviation

Answer : For FM signal, the frequency deviation Independent of the modulation frequency

Description : Define stub. Explain single and double stub in brief with neat sketch.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Description : Define and explain the term beam width related to antenna with a sketch.

Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Description : Define critical frequency w.r. to wave propagation.

Answer : Define critical frequency w.r. to wave propagation.

Description : Define VSWR with refernce to standing waves.

Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

Description : Define sensitivity with graph.

Answer : Define sensitivity with graph.

Description : Define PAM, PWM, and PPM. Draw waveforms.

Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Description : Define the transmission line? Draw it‟s general equivalent circuit.

Answer : Transmission line: A conductor or conductors designed to carry electricity or an electrical signal over large distances with minimum losses and distortion.  Equivalent circuit:

Description : Define: 1)Frequency 2)Bandwidth 3)Wavelength 4)Time period

Answer : Frequency: Frequency is the number of cycles per second. Bandwidth: A range of frequencies within a given band, in particular that used for transmitting a signal. Wavelength: Wavelength can be defined as ... for one complete cycle of vibration to pass a given point.  OR Time period=1/frequency

Description : State the types of electromagnetic polarization? Define any one of it.

Answer : Transverse electromagnetic wave:- The polarization of a plane EM wave is simply the orientation of the electric field vector with respect to the surface (i.e. looking at the horizon) If ... the field strength varies with change in polarization the wave is said to have an elliptical polarization 

Description : Define fading? List the causes.

Answer : The fluctuation in signal strength at a receiver, which is mainly due to the interference of two waves which left the same source but arrived at the destination by different paths, is known ... , such as irrigation, or from multiple transmission paths, irregular earth surfaces, and varying terrains.

← Prev Question Next Question →
Ask a Question
Choose topic