Define modulation index in AM and give its formula.

1 Answer

In AM wave, the modulation index (m) is defined as the ratio of the amplitude of the modulating signal (Vm ) to the amplitude of carrier signal (Vc). m = Vm / Vc
Like 0 like Dislike 0 dislike

Related questions

Description : Give the expression for modulation index for AM and FM.

Answer : 1.Modulation index for AM ma=Vm / Vc Where Vm is modulating voltage Vc is the carrier voltage 2.Modulation index for FM mf=δ /fm where δ is the deviation fm is the modulating frequency

Description : Define modulation? State the desirable value of modulation index of AM.

Answer : Modulation: It is the process in which any of these Parameters (Amplitude, Frequency, Phase) of high frequency signal (carrier signal) are varied in accordance with low frequency signal(modulating signal) For an AM, modulation index range is 0 to 1.

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

Description : Define pulse modulation. State its types. 

Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Description : Define selectivity and sensitivity of AM Receiver. 

Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Description : Draw the block diagram of AM transmitter, explain its operation.

Answer : AM transmitter is of two types i)High Level AM Transmitter ii)Low Level AM Transmitter i) RF crystal oscillator: It is a source of carrier signal of desired frequency. The circuit is ... AM signal is then applied to the transmitting antenna which radiates this AM signal into air or space. 

Description : i) State the significance of modulation index in AM transmission. ii) Explain the effect of modulation index on AM wave with waveforms.

Answer : Significance of modulation index in AM transmission  It is used to determine the strength and quality of transmitted signal. If the modulation index is small, then the amount of variation in ... amplitude part of its information is lost in the process of modulation which is undesirable.

Description : In amplitude modulation AM, if modulation index is more than 100% then: (1) Power of the wave increases. (2) Efficiency of transmission increases. (3) The wave gets distorted. (4) Bandwidth increases

Answer : In amplitude modulation AM, if modulation index is more than 100% then: The wave gets distorted.

Description : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly:  (1) 8.24 KW (2) 9.26 KW (3) 8.47 KW (4) 9.6 KW

Answer : If the radiated power of AM transmitter is 10 KW, the power in the carrier for modulation index of 0.6 is nearly: 8.47 KW.

Description : If modulation index is 0.6, maximum power efficiency (in %) of AM is about  A) 60 B) 30 C) 20 D) 10

Description : Compare AM with FM with respect to following points: a) Definition. b) Modulation index. c) Bandwidth. d) Side band.

Answer : Parameters AM FM Definition It is the process in which the amplitude of carrier signal is varied in accordance with the instantaneous value of modulating signal keeping frequency and ... frequency deviation. Side band There are two sidebands Infinite number of sideband

Description : A gaseous organic compound that is best known for its use in preservative solutions has the chemical formula HCHO (read: H - C - H CHEM-92; Short Answer: Give me the name and atomic number ... element is a clear, odorless gas. This element is one of the essential ingredients in the burning process.

Answer : ANSWER: OXYGEN ATOMIC NUMBER = 8

Description : Explain how modulation reduces height of antenna and avoid mixing of signals.

Answer : Modulation reduces antenna height: For the transmission of radio signals, the antenna height must be multiple of λ/4 ,where λ is the wavelength . λ = c /f where c : is the ... will occupy different slots in the frequency domain (different channels). Thus, modulation avoids mixing of signals.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz

Description : Show that AM wave consist of two side bands and carrier. Also prove the bandwidth of AM is double of the modulating frequency.

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Description : State the need of modulation.

Answer : Need of Modulation :- i)Reduction in the height of antenna  ii) Avoids mixing of signal  iii) Increases range of communication.  iv) Multiplexing is possible v) Improve quality of reception.

Description : Explain effect of 'm' on AM with neat waveforms.

Answer : i)m< 1  If m < 1 or if the percentage of modulation is less than 100% the this type of modulation is known as under modulation The amplitude of modulating signal less than carrier ... greater amplitude part of its information is lost in the process of modulation which is undesirable.

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Description : Explain the demodulation of AM signal using diode detector.

Answer : Simple diode detector:- Explanation:- This is essentially just a half wave rectifier which charges a capacitor to a voltage nearly to the peak voltage of the incoming AM waveform s(t). ... detector output is proportional to the signal strength. Stronger Am signal higher is the dc AGC voltage.

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

Description : Define modulation index of FM.

Answer : Modulation index of FM is defined as the ratio of the frequency deviation to the modulating frequency.

Description : Define rectification efficiency. Give its formula.

Answer : The ratio of output DC power delivered to the load to the applied input AC power is called rectification efficiency. It is denoted by η. η = Output DC power delivered to the load / Input AC power from transformer secondary η = Pdc / Pac

Description : Dish antenna is parabolic in shape and has meshy structure. Give reasons.

Answer : A Practical reflector employing the properties of the parabola will be a three dimensional bowl-shaped surface, obtained by revolving the parabola about the axis AB. The resulting geometric ... (directrix) is constant. These geometric properties yield an excellent microwave or light reflector. 

Description : Explain any four different frequency bands and give their two applications of each.

Answer : Explain any four different frequency bands and give their two applications of each.

Description : Define stub. Explain single and double stub in brief with neat sketch.

Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching. 

Description : Define and explain the term beam width related to antenna with a sketch.

Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Description : Define PAM, PWM, and PPM. Draw waveforms.

Answer : Pulse amplitude modulation is defined as a process of varying the amplitude of the carrier pulse in accordance to the modulating signal variations. Pulse width modulation is defined as a ... of varying the position of the carrier pulse, in accordance to the modulating signal variations.

Description : Define electromagnetic wave and polarization.

Answer : Electromagnetic wave:-An electromagnetic wave such as light consists of a coupled oscillating electric field and magnetic field which are always perpendicular; by convention Polarization:-polarization" of electromagnetic waves refers to the direction of the electric field.

Description : Define the term baluns and explain where is it used?

Answer : A type of electrical transformer used to connect an unbalanced circuit to a balanced oneORA balun is a type of transformer: it's used to convert an unbalanced signal to a balanced ... :- In audio applications, baluns convert between high-impedance unbalanced and low impedance balanced lines.

Description : Define: (i) Image frequency and (ii) Double spotting

Answer : i)Image frequency:- Image Frequency is defined as the signal frequency plus twice the intermediate frequency. It is denoted as fsi = fs+2fi Where, fs = Signal Frequency fi =intermediate frequency ... It is due to the poor front end selectivity i.e., inadequate image frequency rejection.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

Description : Draw the circuit diagram of practical diode detector and explain its working. 

Answer : Circuit diagram of practical diode detector:  Explanation- The circuit operates in the following manner- The diode has been reversed so that now the negative envelope is demodulated. Due to this ... to produce AGC voltage. The DC AGC voltage is proportional to the amplitude of AM signal. 

Description : Draw the circuit diagram of limiter and explain its working.

Answer : Circuit diagram of amplitude limiter:- Explanation:- 1. In frequency modulation, the signal amplitude is held constant while the carrier frequency is varied. 2. Any noise that contaminates ... V p-p instead of the alternately driven into saturation and cutoff, it limits the signal amplitude

Description : Draw the TRF receiver block diagram and explain its working. 

Answer : Explanation:- 1. TRF receivers are simple and having high sensitivity. The AM transmission takes place in MW band and SW band. MW frequency range is 540KHz to 1640KHz. 2. ... power level to drive the loudspeaker. 7. The loudspeaker converts electrical signal into original sound information.

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

Description : Draw the structure of horn antenna and its radiation pattern. List its any two applications.

Answer : The structure of horn antenna Radiation pattern of Horn Antenna Application:- i) Used at microwave frequency. ii) Used in satellite tracking 

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Description : Define critical frequency w.r. to wave propagation.

Answer : Define critical frequency w.r. to wave propagation.

Description : Define VSWR with refernce to standing waves.

Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

Description : Define sensitivity with graph.

Answer : Define sensitivity with graph.

Description : Define the transmission line? Draw it‟s general equivalent circuit.

Answer : Transmission line: A conductor or conductors designed to carry electricity or an electrical signal over large distances with minimum losses and distortion.  Equivalent circuit:

Description : Define: 1)Frequency 2)Bandwidth 3)Wavelength 4)Time period

Answer : Frequency: Frequency is the number of cycles per second. Bandwidth: A range of frequencies within a given band, in particular that used for transmitting a signal. Wavelength: Wavelength can be defined as ... for one complete cycle of vibration to pass a given point.  OR Time period=1/frequency

Description : State the types of electromagnetic polarization? Define any one of it.

Answer : Transverse electromagnetic wave:- The polarization of a plane EM wave is simply the orientation of the electric field vector with respect to the surface (i.e. looking at the horizon) If ... the field strength varies with change in polarization the wave is said to have an elliptical polarization 

Description : Define fading? List the causes.

Answer : The fluctuation in signal strength at a receiver, which is mainly due to the interference of two waves which left the same source but arrived at the destination by different paths, is known ... , such as irrigation, or from multiple transmission paths, irregular earth surfaces, and varying terrains.

Description : Define the following terms: (i) Polarization (ii) Antenna gain (iii)Antenna resistance (iv)Directivity

Answer : i) Polarization:- It is defined as the direction of electric field vector in the EM wave radiated by the transmitting antenna. ii) Antenna Gain:- Antenna gain is defined as the ratio of ... in only one direction in which the radiation is maximum. That is directivity = Max. directive gain

Description : Define the terms: 1) Maximum usable frequency 2) Fading

Answer : 1)Maximum usable frequency:- Maximum usable frequency is defined as the limiting frequency ,when the angle of incidence is other than the normal . OR The highest frequency that can be used for sky ... which left the same source but arrived at the destination by different paths is known as fading.

Description : Define standing wave ratio. 

Answer : Standing wave ratio is defined as the ratio of maximum voltage (Vmax) to minimum voltage (Vmin). Standing wave ratio is also defined as the ratio of maximum current (Imax) to minimum current (Imin).

← Prev Question Next Question →
Ask a Question
Choose topic