search
person

Which rotor is use for high speed in turbo alternators?

1 Answer

Non-salient pole rotor is used for high speed in turbo alternators.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Salient pole rotor is use for which speed?

Answer : Salient pole rotor is use for low and medium speed prime movers.

Description : An electric motor in which both stator field and rotor rotates with same speed is called?

Answer : An electric motor in which both stator field and rotor rotates with same speed is called synchronous motor.

Description : The number of cycles in which a high speed circuit breaker can complete its operation is  (A) 3 to 8 (B) 10 to 18 (C) 20 to 30 (D) 40 to 50

Answer : The number of cycles in which a high speed circuit breaker can complete its operation is 3 to 8

Description : State the advantages of use of high voltage in transmission of Electric power. 

Answer : Advantages: 1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases, its ... high voltage transmission line, successful interconnection of transmission line is possible than low voltage. 

Answer : An exciter for a turbo generator is a shunt generator.

Description : State advantages of short pitch winding over full pitch winding in alternators. 

Answer : Advantages of Short Pitch Winding over Full Pitch Winding in Alternators: 1) Short pitching reduces the amount of copper needed for end connection when compared with full pitched coil. 2) They ... reduced, thereby increasing the efficiency. 4) The power quality of generated emf is improved. 

Description : State advantages of rotating field type alternators. 

Answer : Advantages of Rotating Field Type Alternator: 1) For high-voltage alternator, large space is required to accommodate conductors with insulation, as high voltage is induced in them. If field poles are placed ... is kept rotating. 8) Rotating field is comparatively light and can run with high speed. 

Description : Is the speed of alternator is directly proportional to frequency?

Answer : Yes, speed of alternator is directly proportional to frequency.

Description : In dc machines, the armature windings are placed on the rotor because of the necessity for  (1) electromechanical energy conversion (2) generation of voltage (3) commutation (4) development of torque

Answer : 3  Commutation

Description : Ratio of the rotor reactance X to the rotor resistance R for a two-phase servo motor (A) is equal to that of a normal induction motor (B) is less than that of a normal induction motor (C) ... than that of a normal induction motor (D) may be less or greater than that of a normal induction motor

Answer : C

Answer : In a hysteresis motor, the rotor must have retentivity.

Description : Explain with neat circuit diagrams the procedures to perform no load and blocked rotor tests on three phase induction motor.

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm

Answer : The bearings used to support the rotor shafts are generally ball bearings.

Answer : Locked rotor current of a shaded pole motor is slightly more than full load current.

Answer : The rotor of a hysteresis motor is made of chrome steel.

Answer : The rotor developed by a single-phase motor at starting is zero.

Description : What is the rotor of a motor?

Answer : Rotor is the rotating or moving part in motor and generator.

Description : Wire-wound resistors are unsuitable for use at high frequencies because they?

Answer : Wire-wound resistors are unsuitable for use at high frequencies because they exhibit unwanted inductive and capacitive effects.

Answer : For measurement of inductance having high value, we should use Hay's bridge.

Answer : For measuring a very high resistance we should use Meggar.

Answer : For measuring current at high frequency we should use thermocouple instrument.

Answer : Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of D.C. series motor.

Description : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Answer : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Description : Which capacitor is used for high frequency?

Answer : For constant torque drive armature voltage control speed control method is preferred.

Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Description : For high efficiency of transfer of power, internal resistance of the source should be?

Answer : For high efficiency of transfer of power, internal resistance of the source should be less than the load resistance.

Answer : For measurements on high voltage capacitors, the suitable bridge is Schering bridge.

Answer : MOSFET provides better efficiency at high frequency and its high speed switching losses are less hence MOSFET is used for high frequency.

Description : Which of the following circuit breakers has high reliability & minimum maintenance?  (A) Bulk oil type CB (B) Air blast CB (C) Vacuum CB (D) Sulphur hexafluoride CB 

Answer : Which of the following circuit breakers has high reliability & minimum maintenance?  (A) Bulk oil type CB (B) Air blast CB (C) Vacuum CB (D) Sulphur hexafluoride CB 

Description : Which type of ADC gives high resolution?

Answer : Sigma Delta, successive approximation and integrating type analogue to digital converter gives very high resolution but they have slower speed.

Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

Answer : The stator of phase shifting transformer for use in conjunction with an A.C. potentiometer usually has a two-phase winding.

Description : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Answer : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Description : Can I use C++ for Arduino?

Description : Can you use Python for Arduino?

Answer : Series motor has the poorest speed control.

Description : Synchronous motor always runs at which speed?

Answer : Synchronous motor always runs at synchronous speed.

Description : Which motor has the best speed regulation?

Answer : Depreciation charges are high in case of thermal plant.

Answer : The contacts of high voltage switches used in power system are submerged in oil. The main purpose of the oil is to extinguish the arc.

Description : Why high voltage is used in power transmission?

Answer : The primary reason that power is transmitted at high voltages is to increase efficiency. ... The lower current that accompanies high voltage transmissionreduces resistance in the conductors aselectricity flows ... This means that thin, light-weight wires can beused in long-distance transmission.

Description : Limitation and application of High Voltage DC (HVDC)

Answer : Limitation and application of High Voltage DC (HVDC) :  Limitation:- 1) It is difficult to step up and step down DC voltage like AC voltage. 2) Special cooling ... conventional/non-conventional) 12) Increasing existing grid utilization. 13) Interconnection of different grids or networks

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

Description : At very high temperatures, extrinsic semiconductor becomes intrinsic semiconductor because (A) Of drive in diffusion of dopants & carriers. (B) Band to band transition dominates impurity ionization. (C) ... band to band transition. (D) Band to band transition is balanced by impurity ionisation.

Answer : At very high temperatures, extrinsic semiconductor becomes intrinsic semiconductor because Impurity ionization dominates band to band transition.

Description : All good conductors have high?

Answer : All good conductors have high conductance.

Description : Power factor of the system is kept high?

Answer : Power factor of the system is kept high to reduce line losses, to maximise the utilization of the capacities of generators, lines and transformers, to reduce voltage regulation of the line.

← Prev Question Next Question →
editChoose topic
...