What is the definition of extra low voltage?

1 Answer

Extra-low voltage (ELV) is an electricity supply voltage in a range which carries a low risk of dangerous electrical shock.

Like 1 like Dislike 0 dislike

Related questions

Description : What is Extra High Voltage?

Description : What is meant by extra high voltage transmission?

Answer : HT & LT  two types transmission in industrial line 

Description : What is the difference between a line voltage and low voltage control system?

Description : What is considered low voltage and high voltage?

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

Description : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Answer : Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

Description : What is the definition of induction motor?

Answer : its working on magnetic base made by coils and its work with 1 phase or 3 phase ac or dc supply

Description : What is the definition of electromagnetic force?

Description : What is the definition of electronic communication?

Description : What is the definition of a primary instrument?

Description : What is the definition of brownout?

Description : What is the definition of an electrical system?

Description : What is the definition of wind energy?

Answer : Motion of atmosphere of earth is called wind and its kinetic energy is called wind energy

Description : What is meant by flash over voltage?

Description : What is dielectric withstand voltage?

Description : What is the difference between line and phase voltage?

Answer : Line voltage  is  voltage  between two  phases R &Y  (415 v)  while  phase  voltage  is  the  voltage  between  one  phase and  a neutral  B &  N   (240 v).

Description : What is impulse voltage of transformer?

Description : What are the advantages of high voltage transmission?

Answer : Advantages:  1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases ... line increases  12. As transmission voltage increases power handling capacity of transmission line increases 

Description : What is a high voltage test?

Description : In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Answer : In voltage source converter based HVDC transmission system the active power is controlled by changing phase angle of the converter ac input voltage

Description : How do you fix voltage drop?

Description : Why high voltage test is done?

Description : Why high voltage can reduce power loss?

Answer : when voltage has increased due to reduced current flow, thus power loss given by ( I^2R) will be low due to reduced current(I^2) provided that resistance (R) is constant.

Description : Why does increase in current mean a decrease in voltage?

Answer : This is because current flows from high potential to low potential to bring the two diffrent potential to unity , thus  a reduced potential (voltage)

Description : Why high voltage is used in power transmission?

Answer : The primary reason that power is transmitted at high voltages is to increase efficiency. ... The lower current that accompanies high voltage transmissionreduces resistance in the conductors aselectricity flows ... This means that thin, light-weight wires can beused in long-distance transmission.

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Description : Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Answer : Following are the methods used to measure resistances:-  (i) Low resistance: 1.Voltmeter-Ammeter Method 2. Kelvin's Double bridge Method  (ii) Medium resistance: 1.Voltmeter-Ammeter Method 2. ... of Charge Method  (iv) Earth resistance : 1. Fall of Potential Method 2. Earth tester

Description : State the range for low and medium resistance.

Answer : Low resistances: less than 1 ohm.  Medium resistances: 1 ohm to 0.1 Mega ohm. 

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

Description : Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

Answer : Accurate measurement of very low resistances is possible with Kelvin’s Double Bridge

Answer : Turbine used for low head is Kaplan turbine.

Description : At very low frequencies a series R-C circuit behaves as almost purely?

Answer : At very low frequencies a series R-C circuit behaves as almost purely capacitive.

Description : In an AC. circuit, a low value of kVAR compared with kW indicates?

Answer : In an AC. circuit, a low value of kVAR compared with kW indicates high power factor.

Answer : In a low power factor wattmeter the pressure coil is connected to the load side of the current coil.

Answer : A synchronous machine with low value of short-circuit ratio has lower stability limit.

Answer : The primary reason for low power factor is supply system is due to installation of induction motors.

Answer : A low utilization factor for a plant indicates that plant is used for stand by purpose.

Answer : To protect most of the electrical equipment handling low power, the types of relays used are thermocouple, electronic and bimetallic.

Description : The efficiency of a transformer, under heavy loads, is comparatively low because?

Answer : The efficiency of a transformer, under heavy loads, is comparatively low because copper loss becomes high in proportion to the output.

Description : At which time power factor of the induction motor is low?

Answer : The power factor of the inducction motor is low at the time of starting as compare to while the induction motor is running.

Description : write short notes on Low-pass filter.

Answer : low-pass filter (1) filter exhibiting frequency selective characteristic that allows low-frequency components of an input signal to pass from filter input to output unattenuated all high-frequency components are ... the bandwidth of the filter. A filter whose impulse response is a low-pass signal.

Answer : MOSFET have high current losses due to High on state resistance. Hence MOSFET is used for low power applications.

Description : What is terminal voltage ?

Description : What kills, current or voltage?

Answer : Current would kill. You can actually have thousands of bolts going through you and not even know it. Yes you probably know already voltage is current times resistance. Since your body is a resistor it would take just a small amount of current to create a very high voltage

Description : What is internal voltage drop and terminal voltage?

Answer : It is not permissible to just connect the positive terminal to the negative terminal of a cell with a copper wire. It will overheat and get damaged. This happens because the electromotive force (emf) ... than the nominal voltage (emf) of the cell and this lower voltage is called terminal voltage.

Description : What is line voltage and phase voltage? Draw balanced three phase star connected system. Show all the voltages and currents.

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Description : What is a capacitor voltage transformer? A) It is a transformer used in power systems to step up low voltage signals and provide extra high voltage B) It is a transformer used in power systems ... in power systems to step down extra high voltage signals and provide low voltage D) None of these

Answer : What is a capacitor voltage transformer? A) It is a transformer used in power systems to step up low voltage signals and provide extra high voltage B) It is a transformer used in power systems ... power systems to step down extra high voltage signals and provide low voltage D) None of these

Description : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

Answer : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

← Prev Question Next Question →
Ask a Question
Choose topic