search
person
What should be the ideal resistance of ammeter ?

1 Answer

Ideal resistance of ammeter should be zero.

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : An ideal voltage source should have?

Answer : An ideal voltage source should have zero source resistance.

Answer : An ideal traction system should have easy speed control, high starting tractive effort, equipment capable of with standing large temporary loads.

Description : The gain of an ideal amplifier must be

Answer : The gain of an ideal amplifier must be infinity

Answer : Ammeter is a current measuring device having low internal resistance so as to direct all the current flowing in the circuit through it. Hence Ammeter is always connected in series with the circuit. If ... If Ammeter is connected in parallel with the supply, then the supply will be a short circuit.

Description : what is ammeter ?

Answer : An instrument that is used to measure the amount of current flowing in a circuit.

Description : What are the desirable characteristics of ideal switch?

Answer : Desirable characteristics of the ideal switch: It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics. Zero resistance when ... . 100% efficiency. Able to control power flow with zero power dissipation.

Description : what is ideal voltage source?

Answer : every voltage source have their own resistance that is called as internal resistance it is because of the resistance of electrodes and electrolytes in the battery interms of other supplyit have ... in universe it means ideal voltage source is this voltage source having internal resistance zero

Description : Use Voltmeter, ammeter, wattmeter to determine active, reactive and apparent power consumed in given R-L series circuit, draw phasor diagram.

Answer : Practical Significance In the industry environment Electrical Engineering diploma graduate are expected to measure basic parameters like voltage, frequency, time period etc. for R-L series circuits. Therefore ... /varying L. 7. Draw the phasor diagram for each of reading for verification.

Description : Write any two disadvantages of ammeter shunts.

Answer : Disadvantages of ammeter shunts: 1. Errors are caused because of change in temperature. 2. Most suitable for DC measurement. 3. Power loss takes place.

Description : With neat diagram, explain the working of clip-on ammeter.

Answer : Working of Clip on Ammeter: Clip on ammeters are used to measure the high current flowing through bus bar, cable or fuse holders, which act as primary. It consists of split core current ... then clipped over the current carrying conductor. The dial will record the current directly. 

Description : Describe procedure for calibration of ammeter with diagram.

Answer : Procedure for Calibration of Ammeter:  In this method, DC potentiometer is used for measurement of voltage across a standard low resistance.  Connect the circuit as shown in the figure, ... S = resistance of potentiometer  And the currents are compared for finding out error in ammeter.

Description : How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Answer : Extension of A.C. Ammeter Range: The range of a.c. ammeter can be extended by using CT, the arrangement is shown in figure. The CT is current transformer having less number of primary turns carrying high ... high magnitude of source voltage. In this way range of a.c. voltmeter can be extended.

Description : State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Answer : Phase Sequence Indicator:  1. For finding correct phase sequence of supply  2. For obtaining exact instant of parallel operation of alternators.  3. For obtaining reversal of rotation ...  4. In electroplating industries   5. In various processes industries for measuring power factor

Description : Draw a typical electric circuit including ammeter and voltmeter.

Answer : The figure shows typical electric circuit including ammeter and voltmeter. Ammeter is connected in series for measurement of current. Voltmeter is connected in parallel for measurement of voltage. Fuse is use ... are used. If the electric supply is DC the DC ammeter and DC voltmeter are used.

Answer : The function of shunt in an ammeter is to by pass the current.

Answer : An ammeter is a secondary instrument.

Answer : Yes it can...

Description : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

Answer : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

Description : An ideal voltage source has?

Answer : An ideal voltage source has zero internal resistance.

Answer : For any type of consumer the ideal tariff is three part tariff.

Answer : An ideal transformer is one which has no losses and magnetic leakage.

Answer : An ideal transformer will have maximum efficiency at a load such that copper loss equal to iron loss.

Description : When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high ... high value of charging current (D) Cables have a low value of capacitance and initial resistance

Answer : When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because Cables have a high value of capacitance which draws a high value of charging current

Description : For maximum transfer of power, internal resistance of the source should be?

Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

Description : In a transformer the resistance between its primary and secondary should be?

Answer : In a transformer the resistance between its primary and secondary should be infinity.

Answer : For measuring a very high resistance we should use Meggar.

Description : Ratio of the rotor reactance X to the rotor resistance R for a two-phase servo motor (A) is equal to that of a normal induction motor (B) is less than that of a normal induction motor (C) ... than that of a normal induction motor (D) may be less or greater than that of a normal induction motor

Answer : C

Description : Which diode exhibits negative resistance characteristic? (A) LED (B) Zener (C) Tunnel diode (D) PN diode

Answer : Which diode exhibits negative resistance characteristic? (A) LED (B) Zener (C) Tunnel diode (D) PN diode

Description : What is the resistance of an ideal ammeter? 

Answer : ANSWER: ZERO

Description : Write measures to be taken to maintain the insulation resistance of electrical machines to healthy levels.

Description : A star circuit has element of resistance R/2. The equivalent delta elements will be?

Answer : The internal resistance of the ammeter should ideally be Zero.

Answer : The internal resistance of an ammeter should be Very small.

Description : What do you mean by exciting resistance and exciting reactance?

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Answer : equivalent resistance

Description : What is the mathematical relationship between resistance and conductance?

Description : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

Answer : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

Description : What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled? A) It doubles B) It becomes 4 times C) It becomes 2π times D) It remains the same

Answer : Automatically the resistivity will increase as they are the factors affecting the resistivity 

Description : Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

Answer : Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

Description : What is the resistance of a 160 m wire with a uniform diameter of 0.28 mm, if the specific resistance is 12.32 μΩ-cm? A) 3.2 Ω B) 3.2 μΩ C) 0.8 Ω D) None of these

Answer : What is the resistance of a 160 m wire with a uniform diameter of 0.28 mm, if the specific resistance is 12.32 μΩ-cm? A) 3.2 Ω B) 3.2 μΩ C) 0.8 Ω D) None of these

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Description : What is the relationship between power and resistance?

Answer : P = I2R Where P = power I = Current R = Resistance

Description : What happens to the resistance when the current increases?

Answer : Resistance  reduces  when  current  increases.

Description : What is meant by resistance heating?

Description : What is the lowest acceptable insulation resistance for a cable?

Description : What is an insulation resistance test?

Answer : Unit of resistance is Ohm.

Description : State the procedure for testing of earth pit resistance with necessary diagrams.

Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3 ... of that earthing pit. In this test the accuracy is less but electrical rods are not required. 

Description : State the impact of inductance and resistance on transmission line performance

Answer : Impact of inductance on transmission line: 1) It causes IXL drop in transmission line which affects regulation. 2) It is the only parameter which decides power transmission capacity of line i. ... is very small, it causes losses, temperature rise& poor voltage regulation so it cannot be neglected

← Prev Question Next Question →
editAsk a Question
...