Write short notes on: 1) Phosphor characteristics 2) Liquid crystal display

Question

asked Mar 2, 2018 by anonymous

Write short notes on:

1) Phosphor characteristics

2) Liquid crystal display

411 views

Please log in or register to answer this question.

← Prev Question Next Question →

Related questions

asked Jan 7, 2018 by anonymous

Liquid Crystal Display (LCD)

Last answer: Liquid Crystal Display (LCD) LCD stands for Liquid Crystal Display. It is a flat panel electronic display device which uses light modulating properties of liquid crystal. ... pixel and passive pixel display do not consist of switch at each pixel.

0 like 0 dislike

63 views 1 answer

asked Mar 9, 2018 by anonymous

Write short notes on diode.

Last answer: Diode is made from semiconductor material like silicon or germanium. Diode may use as rectifier which convert AC to DC. It is a electronic component. It is two terminal device, one is anode and second is ... in one direction. Diode is made from P-type and N-type material. Diode have a PN junction.

0 like 0 dislike

104 views 1 answer

asked Mar 9, 2018 by anonymous

Write short notes on Arduino.

Last answer: Arduino: Arduino is a open source hardware and software. Arduino is a microcontroller. Since Arduino is open source it have many manufacturer. Arduino project was started in about year ... many sensors to the Arduino. Arduino board have microprocessor, crystal oscillator, 5V voltage regulator.

0 like 0 dislike

209 views 1 answer

asked Dec 12, 2017 by anonymous

write short notes on single phase system.

Last answer: A "phase" in an electrical system is often referred to as the waveform (may be voltage or the current) of the power supply. The waveform in an AC system is typically ... domestic household or commercial supplies and street lighting. Industrial supplies requires three phase electrical supply .

2 like 0 dislike

83 views 1 answer

asked Nov 15, 2017 by anonymous

write short notes on BH curve.

Last answer: The B-H curve is the relation between Flux density B in Wb/m2 (on Y Axis) and H in AT/m (on X axis) It is also known as magnetization characteristics. This curve particularly useful ... occurs. At point A' material gets magnetically saturated and the curve becomes flat (parallel to X axis)

1 like 0 dislike

896 views 3 answers

asked Oct 28, 2017 by anonymous

write short notes on Low-pass filter.

Last answer: low-pass filter (1) filter exhibiting frequency selective characteristic that allows low-frequency components of an input signal to pass from filter input to output unattenuated all high-frequency components are ... the bandwidth of the filter. A filter whose impulse response is a low-pass signal.

1 like 0 dislike

108 views 2 answers

asked Oct 28, 2017 by anonymous

write short notes on Linear motor.

Last answer: Normal electrical motor produces rotatory motion same the linear motor produces linear motion. Linear motors have low efficiency. Linear motor can directly produce straight line motion linear motor do not required gears or crank shaft to produce linear motion.

1 like 0 dislike

55 views 1 answer

asked Aug 19, 2019 by anonymous

crystal oscillator and its applications.

Last answer: Need: Any circuit that generates an alternating voltage is called an oscillator. To generate ac Voltage, it takes energy from the dc source. 1. In some applications voltages of low frequency are required where ... generate clock in digital systems. It is used as sweep circuits in TV and CRO.

0 like 0 dislike

63 views 2 answers

asked Sep 5, 2018 by anonymous

Draw the circuit diagram of crystal oscillator and explain its working.

Last answer: To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good. The resonant frequency is given as Fo = 1/( 2 π √LC )

0 like 0 dislike

175 views 1 answer

asked Jun 18, 2018 by anonymous

In a single crystal of an intrinsic semiconductor, the number of free carriers at the Fermi level at room

In a single crystal of an intrinsic semiconductor, the number of free carriers at the Fermi level at room temperature is: A) Half the total number of electrons in the crystal B) Zero C) Half the number of atoms in the crystal D) Half the number of free electrons in the crystal

Last answer: In a single crystal of an intrinsic semiconductor, the number of free carriers at the Fermi level at room temperature is: Zero

0 like 0 dislike

150 views 1 answer

asked Mar 10, 2018 by anonymous

What is a crystal oscillator?

0 like 0 dislike

45 views 0 answers

asked Jan 2 by anonymous

Following are the different liquid propellants used in rocket engines

Last answer: Following are the different liquid propellants used in rocket engines 1. kerosene, Liquid oxygen and Liquid Hydrogen similar to kerosene 2. Alcohol and its derivatives (Ethyl Alcohol) 3. hydrazine and its derivatives 4. Hydrogen peroxide 5. liquid hydrogen

0 like 0 dislike

3 views 1 answer

asked May 7, 2020 by anonymous

State gaseous and liquid insulating material.

Last answer: i) Gaseous insulating material : 1. Air 2. Nitrogen 3. Hydrogen 4. SF6 ii) liquid insulating material: 1. Transformer oil 2. Capacitor oil 3. Cable oil 4. Pyranol 5. Savotal 6. Savol 7. Vegetable oil 8. Silicon liquids

0 like 0 dislike

51 views 1 answer

asked Sep 7, 2018 by anonymous

Give examples of different types of fuels. Also state any two advantages of liquid fuels over solid fuels.

Last answer: Examples of different types of fuels:- 1. Indian Coal : It contain 30 to 40 % ash but sulphur content is less than 1%.. 2. Imported coal: It contents low ash about 10% but sulphur ... can be controlled to match the load requirements. 13. Rapid and efficient starting of the boilers from cold.

0 like 0 dislike

58 views 1 answer

asked Apr 30, 2018 by anonymous

The material used in liquid fuses is

The material used in liquid fuses is (1) SF6 (3) carbon tetra chloride (2) distilled water (4) transformer oil

Last answer: The material used in liquid fuses is carbon tetra chloride

0 like 0 dislike

256 views 1 answer

asked Apr 26, 2018 by anonymous

Liquid flow rate is measured using

Liquid flow rate is measured using (A) a pirani gauge (B) a pyrometer (C) an orifice plate (D) a bourdon tube

Last answer: Liquid flow rate is measured using an orifice plate

0 like 0 dislike

78 views 1 answer

asked Jan 24, 2018 by anonymous

Liquid Crystal Display (LCD) in embedded system

Last answer: Liquid Crystal Display:-An LCD is a low-cost, low power device capable of displaying text and images. LCD's are extremely common in embedded systems since such system often does not have video monitors ... toggles the enables bit and acts as a delay so that the command can be processed and executed.

1 like 0 dislike

135 views 1 answer

asked Jul 30, 2019 by anonymous

Write short notes on fire extinguishing methods adopted in electrical engineering.

Last answer: Stand 6 to 8 feet away from the fire and follow the four-step PASS procedure. If the fire does not begin to go out immediately, leave the area at once. Always be sure ... fire causing the particles to expand chemically inhibiting combustion and expelling the oxygen thereby smothering the flames.

0 like 0 dislike

141 views 3 answers

asked Aug 11, 2018 by anonymous

Write short notes on 3 phase AC system.

0 like 0 dislike

107 views 0 answers

asked Nov 15, 2017 by anonymous

write short notes on thyristor CSI .

Last answer: Current-source inverter (CSI) is an inverter with a DC current input. Current source inverters are most commonly used in very high power AC motor drives.

1 like 0 dislike

90 views 2 answers

asked Mar 19, 2020 by anonymous

KVL solved problem non linear load VI characteristics equation

Last answer: https://youtu.be/fgQTs-1hq7Q

0 like 0 dislike

44 views 1 answer

asked Oct 19, 2019 by anonymous

Diode VI characteristics

Last answer: Diode VI characteristics

0 like 0 dislike

209 views 1 answer

asked Oct 13, 2019 by anonymous

Draw symbol & V-I characteristics of (i) LASCR (ii) DIAC (iii) TRIAC

Last answer: (i) LASCR: (ii) DIAC: (iii) TRIAC:

0 like 0 dislike

669 views 1 answer

asked Sep 2, 2019 by anonymous

basic characteristics of sound signal.

Last answer: Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio.

0 like 0 dislike

77 views 1 answer

asked Aug 4, 2019 by anonymous

Compare characteristics of asynchronous and synchronous transmission mode.

Compare characteristics of asynchronous and synchronous transmission mode (four points).

Last answer: Synchronous transmission Asynchronous transmission 1. Synchronous transmission are synchronized by an external clock. 1. Asynchronous transmission are synchronized by special signals along the transmission ... for transferring a small amount of data as it is simple and economical.

0 like 0 dislike

60 views 1 answer

asked Aug 2, 2019 by anonymous

Explain the characteristics of solar cell.

Last answer: Characteristics of solar cell : Explanation :- Solar cells produce direct current ( DC ) electricity and current times voltage equals power, so we can create solar cell I-V curves representing ... system so that it can operate as close to its optimal peak power point (MPP) as possible.

0 like 0 dislike

85 views 1 answer

asked Jul 29, 2019 by anonymous

State characteristics of force.

Last answer: i) Magnitude: The quantity of force e.g. 10 N, 100 kN etc. ii) Direction: It is the line along which the force acts. It is also called as line of action of the force. iii) Point of ... . Push: If the arrow head is pointed towards the point of application, the nature of the force is push.

0 like 0 dislike

62 views 1 answer

asked Jul 25, 2019 by anonymous

Draw a symbol and neat labeling V-I characteristics of GTO and explain its operation.

Last answer: Ans: Symbol and V-I characteristics of GTO: Operation of GTO: i) As the applied anode to cathode voltage is increased above zero, very small current (leakage current) flows through the device. ... low voltage (VBRR). The reverse breakdown voltage is of the order of 20 to 30 volt only.

0 like 0 dislike

335 views 1 answer

asked Jul 25, 2019 by anonymous

Draw a neat labelling V-I characteristics of SCR and explain the region

Last answer: (i) Latching current: It is the minimum anode current required to maintain the SCR in the conduction state just after turn-on and the gate signal has been removed. (ii) Holding current: It is the minimum anode current required to hold the conducting SCR in the ON state.

0 like 0 dislike

393 views 2 answers

asked Jun 29, 2019 by anonymous

List three important characteristics of an electric circuit.

0 like 0 dislike

211 views 0 answers

asked Jun 29, 2019 by anonymous

What is the smallest unit of a compound with the same chemical characteristics?

Last answer: The molecule is the smallest unit of a compound with the same chemical characteristics.

0 like 0 dislike

89 views 1 answer

asked May 8, 2018 by anonymous

The following is/are the characteristics of SF6 circuit breakers:

The following is/are the characteristics of SF6 circuit breakers: (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

Last answer: The following is/are the characteristics of SF6 circuit breakers: (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

0 like 0 dislike

81 views 1 answer

asked Apr 28, 2018 by anonymous

The terminal characteristics of a dc generator suitable for electric welders is

The terminal characteristics of a dc generator suitable for electric welders is (A) separately excited generator (B) shunt generator (C) series generator (D) differentially compounded generator

Last answer: The terminal characteristics of a dc generator suitable for electric welders is differentially compounded generator

0 like 0 dislike

86 views 1 answer

asked Apr 26, 2018 by anonymous

Which of the following does not show non-linear V-I characteristics?

Which of the following does not show non-linear V-I characteristics? (A) Schottky diode (B) Tunnel diode (C) Thermistor, at a fixed temperature (D) p-n Junction diode.

Last answer: Which of the following does not show non-linear V-I characteristics? (A) Schottky diode (B) Tunnel diode (C) Thermistor, at a fixed temperature (D) p-n Junction diode.

0 like 0 dislike

103 views 1 answer

asked Mar 21, 2018 by anonymous

The desirable static characteristics of a measuring system are?

Last answer: The desirable static characteristics of a measuring system are accuracy, sensitivity and reproducibility.

0 like 0 dislike

313 views 1 answer

asked Mar 20, 2018 by anonymous

The speed/load characteristics of a universal motor is same as that of?

Last answer: The speed/load characteristics of a universal motor is same as that of D.C. series motor.

0 like 0 dislike

69 views 1 answer

asked Mar 15, 2018 by anonymous

What are the characteristics of a capacitor?

0 like 0 dislike

75 views 0 answers

asked Mar 10, 2018 by anonymous

Explain the characteristics of inductor to be considered while designing it.

Explain the characteristics of inductor to be considered while designing it. What is the effect of over current and increase in temperature on inductor.

0 like 0 dislike

54 views 0 answers

asked Mar 10, 2018 by anonymous

Explain the electrical characteristics of transformer.

Last answer: Transformer electrical characteristics: Area of primary and secondary conductors, Apri and Asec: Winding loss Pw: Flux density and core loss: Leakage inductance: ... transformer span. The rise in temperature may breakdown insulation which may cause failure of the transformer.

0 like 0 dislike

69 views 1 answer

asked Feb 5, 2018 by anonymous

What are the desirable characteristics of ideal switch?

Last answer: Desirable characteristics of the ideal switch: It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics. Zero resistance when ... . 100% efficiency. Able to control power flow with zero power dissipation.

1 like 0 dislike

980 views 1 answer

asked Mar 2, 2018 by anonymous

Write short note on ADC-Amplifier Interface.

Last answer: ADC-Amplifier interface: In most data acquisition system analog to digital converter (ADC) is interfaced with the amplifier. There are different interface architectural schemes. Operational ... . The interaction between analog to digital converter and amplifier affects the system performance.

0 like 0 dislike

96 views 1 answer

asked Jan 24, 2018 by anonymous

Short notes on timers and counters.

Last answer: Timers:-A timer is a peripheral device that can measure time intervals. Timers can be used to1. General events at the specific time or to determine the duration of two external events.eg. Keeping a ... the number of times the car wheel rotates in one second, in order to determine cars speed.

1 like 0 dislike

283 views 1 answer

asked Aug 8, 2017 by anonymous

what is gate turn off thyristor (GTO)?

Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Last answer: Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

0 like 0 dislike

1.6k views 1 answer

asked May 15, 2018 by anonymous

In a dual trace oscilloscope, the display appears segmented when

In a dual trace oscilloscope, the display appears segmented when (a) low frequency signals are observed in Alternate mode (b) low frequency signals are observed in Chop mode (c) high frequency signals are observed in Alternate mode (d) high frequency signals are observed in Chop mode

Last answer: In a dual trace oscilloscope, the display appears segmented when high frequency signals are observed in Chop mode

0 like 0 dislike

128 views 1 answer

asked Jun 29, 2020 by anonymous

List fours characteristics of display and define them.

Last answer: Characteristics of display: 1. Dot pitch: It is the distance between each group (t6riad) of red, blue and green phosphors. A smaller dot pitch helps produce sharper and clearer image 2. Resolution: ... time: Time taken by throughput of a pixel to fully react to a change in its brightness.

0 like 0 dislike

14 views 1 answer

asked 3 days ago by anonymous

Write Unix command for following: i)create a folder OSY ii) create a file FIRST in OSY folder iii) List/display all files and directories. iv) Write command to clear the screen

Last answer: i) create a folder OSY: $mkdir OSY ii)create a file FIRST in OSY folder: $cd OSY $cat>FIRST or $ touch FIRST iii) List/display all files and directories: $ls iv) to clear screen: $clear

0 like 0 dislike

4 views 1 answer

asked Jul 5, 2020 by anonymous

Write a program to declare a class ‘book’ containing data members as ‘title’, ‘author-name’, ‘publication’, ‘price’. Accept and display the information for one object using pointer to that object.

Last answer: #include<iostream.h> #include<conio.h> class book { char author_name[20]; char title[20]; char publication[20]; float price; public: void Accept(); void Display(); }; void ... title \t author_name \t publication \t price\n ; p-> Display(); getch(); }

0 like 0 dislike

359 views 1 answer

asked Jan 8 by anonymous

Write any four purposes of construction notes and any two purposes of north line.

Last answer: Purposes of Construction notes - 1) These include additional information about the structure which can not be shown in drawing. 2) These are useful for better understanding of drawing. 3) ... in drawing with common reference direction. 4) To avoid discrepancies in understanding of drawing.

0 like 0 dislike

5 views 1 answer

asked 5 days ago by anonymous

Which of the following is not a part of a CRT ? (1) Phosphor screen (2) Shadow mask (3) Electron gun (4) Gas plasma

Last answer: Gas plasma

0 like 0 dislike

3 views 1 answer

asked 4 days ago by anonymous

The substance which does not expand on going from liquid state to solid state is (1) Water (2) Cast-iron (3) Aluminium(4) Type metal

Last answer: Type metal

0 like 0 dislike

3 views 1 answer

Write short notes on: 1) Phosphor characteristics 2) Liquid crystal display

Please log in or register to add a comment.

Please log in or register to answer this question.

0 Answers

Related questions