search
person
Explain open emitter BJT drive circuit.

1 Answer

open emitter BJT drive circuit:

image

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

Description : Explain MOSFET gate drive circuit and totem pole configuration.

Answer : MOSFET gate drive circuit: The turning on and turning off of MOSFET can be controlled from gate to source voltage signal. If the gate to source voltage of MOSFET exceeds threshold ... this configuration, the two switches (transistors) are used in totem pole arrangement with a comparator.

Description : Explain DC coupled drive circuit with unipolar output.

Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

Description : Explain thyristor gate drive circuit.

Answer : Thyristor Gate Drive Circuit: The thyristor can be turned on by pulse voltage signal at gate terminal and it does not require continuous drive signal like the transistor. The gate ... circuit provide required minimum gate voltage and gate current then the thyristor conducts properly.

Description : basic gate drive circuit of GTO

Answer : basic gate drive circuit of GTO

Description : Describe the difference between an open circuit and a short circuit.

Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

Answer : It is required to measure the true open circuit e.m.f. of a battery. The best device is D.C. potentiometer.

Description : During open circuit test of a transformer?

Answer : During open circuit test of a transformer primary is supplied rated voltage.

Description : Explain transformer isolated drive circuits providing both signal and power.

Description : Explain the formation of parasitic BJT and parasitic diode in Power MOSFET. Can parasitic diode be used in same power electronics applications?

Answer : Parasitic Diode: The parasitic diode is in between drain and source. The MOSFET structure itself contains parasitic diode or body drain diode. This parasitic diode allows the reverse flow of current when the ... of MOSFET as a BJT collector. Parasitic BJT operates in the cut-off region.

Description : Explain the on state losses in power BJT.

Answer : On state losses in power BJT: Transistor have four types of losses one is turn on state losses second is turn off state losses third is turn on switching losses and fourth is turn ... ON = VCE sat x IC With increasing collector current collector to emitter saturation voltage increases.

Description : What is the need for electrically isolated drive circuits?

Description : What are the fundamental requirements of gate drive ICs?

Description : Why common emitter configuration is commonly used?

Answer : Common emitter configuration is commonly used for amplifications because 1. The common emitter configuration (CE) provides maximum voltage and current gain and hence provides maximum power gain. The ... automatic impedance matching maximum power transfer will take place from one stage to other.

Description : The ac bypassing of RF by CF in a common emitter configuration :  (A) increases ac signal across emitter -base junction (B) decreases ac signal across emitter -base junction (C) decreases voltage amplification (D) stabilizes the Q -point

Answer : The ac bypassing of RF by CF in a common emitter configuration : increases ac signal across emitter -base junction

Description : What is emitter biasing?

Description : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Answer : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Description : What is the difference between beta and forced beta for BJT?

Description : Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.

Answer : Power MOSFET have high turning on and turning off capability high switching speed of MOSFET is due to the high rate of change of drain voltage. The switching losses of power MOSFET ... lower frequency. Hence, operating frequency of power MOSFET is higher than that of power BJT.

Description : Compare BJT, MOSFET and IGBT .

Answer : BJT MOSFET IGBT BJT is a current controlled device. MOSFET is a voltage controlled device. IGBT is a voltage controlled device. The input impedance of BJT is low. ... is minority carrier device. MOSFET is majority carrier device. IGBT is minority carrier device.

Answer : Because it has a higher switching frequency and heat tolerance.

Answer : ON state losses of IGBT is less as compared to MOSFET and BJT.

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

Description : Explain the open delta (delta-delta) test on transformer.

Description : Adjustable-speed drive

Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Answer : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Answer : For constant torque drive armature voltage control speed control method is preferred.

Description : The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

Answer : The synchronous motor which works on leading power factor and does not drive any mechanical load is called synchronous condenser.

Description : What is the difference between AC and DC drive?

Answer : AC means alternating current It's Frequency is 50hz Dc means direct current ItsI Frequency is 0Hz

Description : What is an electric motor drive?

Answer : An electric drive is a complex electromechanical system that drives various actuators in industrial and industrial work machines. In this case, control is carried out using a technological process ... calculation of the kinematic and load characteristics of the electric drive is carried out.

Description : What is a drive in electrical controls?

Description : What does an electric drive do?

Description : Can a power surge erase a hard drive?

Description : Scherbius Drive System

Answer : Scherbius Drive System

Description : Kramer Drive System

Answer : Kramer Drive System Kramer drive is a rotor side speed control drive of induction motor. Slip is the difference between synchronous speed and rotor speed. It is the ... and DC motor. The static Kramer drive is costlier because of the cost of DC motor.

Description : Advantages of Variable Frequency Drive (VFD)

Answer : Advantages of Variable Frequency Drive (VFD)

Description : What are the disadvantages of Open loop control system?

Answer : Open loop control system are less reliable. In open loop control system Optimization is not possible. Open loop control system are less accurate.

Description : Why CT is never operated with an open secondary ?

Answer : CT secondary should never be kept open because it will cause saturation of the core to a high level and very high voltage will appear across the secondary which can breakdown the insulation. One terminal of PT secondary is always grounded to avoid capacitive induction and for human safety

Description : What will happen to the gain margin if the gain of the open loop system is doubled? A) Doubled B) Becomes half C) Is not affected D) Becomes one-fourth 

Answer : What will happen to the gain margin if the gain of the open loop system is doubled? A) Doubled B) Becomes half C) Is not affected D) Becomes one-fourth 

Description : If the gain of the open loop system is doubled, the gain margin  (1) Is not affected (2) Gets doubled (3) Becomes half (4) Becomes one -forth

Answer : If the gain of the open loop system is doubled, the gain margin Becomes half

Description : An open resistor, when checked with an ohm-meter reads?

Answer : An open resistor, when checked with an ohm-meter reads infinite.

Answer : Open circuited armature coil of a D.C. machine is identified by the scarring of the commutator segment to which open circuited coil is connected and indicated by a spark completely around the commutator.

Answer : If the field winding of an unloaded salient pole synchronous motor is open circuited, the motor will stop.

Description : What is an example of an open loop system?

Answer : Open loop system. Ex. Electric heater, washing machine, fan, electric switch, etc

Description : What are the advantages of open loop control system?

Answer : Open loop control system are simple to design. Open loop control system are generally stable.

Description : what is open loop and close loop control system?

Answer : A) In open loop system the input is independent         of output but output is depends on input. A-1. no feedback path in open loop s/m    -2. less accuracy than close loop s/m. Ex. Washing ...    -3. high accuracy. Ex. Air conditioner ( AC ), rocket launcher, radar          system, etc

Description : State 2 advantages of JFET over BJT.

Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

← Prev Question Next Question →
editAsk a Question
...