Explain thyristor gate drive circuit.

1 Answer

Thyristor Gate Drive Circuit:

The thyristor can be turned on by pulse voltage signal at gate terminal and it does not require continuous drive signal like the transistor. The gate circuit is used for triggering or firing thyristor this circuit called triggering circuit or firing circuit. If the gate signal voltage exceeds gate triggering voltage then thyristor turns on. In case of resistive load, the single sharp rising pulse is enough for triggering but in case of inductive load the pulse should be slightly higher than gate triggering current is applied till the successful triggering takes place. The thyristor is used for high voltage levels and there are two circuits one is control circuit and one is triggering circuit. If the thyristor is used for high power applications then the triggering circuit and control circuit should be isolated from the power circuit. This isolation is done to avoid the high transients of voltage and current. Thyristor gate drive circuit may be non-isolated or optically isolated or it may be transformer coupled gate drive circuit. If the firing circuit or triggering circuit provide required minimum gate voltage and gate current then the thyristor conducts properly.

image

Like 0 like Dislike 0 dislike

Related questions

Description : Explain MOSFET gate drive circuit and totem pole configuration.

Answer : MOSFET gate drive circuit: The turning on and turning off of MOSFET can be controlled from gate to source voltage signal. If the gate to source voltage of MOSFET exceeds threshold ... this configuration, the two switches (transistors) are used in totem pole arrangement with a comparator.

Description : basic gate drive circuit of GTO

Answer : basic gate drive circuit of GTO

Description : What are the fundamental requirements of gate drive ICs?

Description : Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

Answer : No we cannot turn off normal thyristor using Gate.

Description : Explain open emitter BJT drive circuit.

Answer : open emitter BJT drive circuit:

Description : Explain DC coupled drive circuit with unipolar output.

Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

Description : Describe the gate circuit for a single phase full converter.

Description : What is the use of a thyristor in a circuit?

Description : Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Answer : Thyristor operated dimmer: A popular thyristor operated dimmer circuit employ TRIAC-DIAC phase control for low AC power control. During each half-cycle, the capacitor charges through (R1+VR1). When the ... time constant {C (R1+VR1)}. Thus by reducing VR1 the lamp brightness can be increased.

Description : Explain transformer isolated drive circuits providing both signal and power.

Description : Explain different gate drives techniques with base circuits and key features.

Description : What is the need for electrically isolated drive circuits?

Description : Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 

Answer : MOSFET is metal oxide field effect transistor. MOSFET is a voltage controlled device. MOSFET is majority carrier device. MOSFET are of two one is n-channel MOSFET and p-channel MOSFET. Gate, ... . Hence, power MOSFET is operated at high enough gate-source voltage to minimize the conduction losses.

Description : Thyristor can be protected from over voltages by using

Answer : Thyristor can be protected from over voltages by using Voltage clamping device

Description : Leakage current flows through the thyristor in

Answer : Leakage current flows through the thyristor in Forward blocking mode and Reverse blocking mode.

Description : What is a phase control thyristor?

Description : Why thyristor are not preferred for inverter?

Description : What is thyristor family?

Description : What is meant by firing angle of thyristor?

Answer : The point at which SCR is triggered is known as firings angle of thyristor.

Description : What is a reverse conducting thyristor?

Description : What is the function of a thyristor?

Description : Why SCR is called as thyristor?

Description : Is a SCR a thyristor?

Answer : Yes, SCR is a thyristor. Thyristor is the family and SCR is the member of that family but SCR is universally known as thyristor.

Description : How is a thyristor used to convert AC to DC?

Description : What is the application of thyristor?

Answer : Yes ,it is one of the main advantage using thristors as a  switch in DC  circuit ,it has a high current gain

Description : parallel operation of MOSFET can be done more easily as compared to thyristor. why?

Answer : Parallel operation of MOSFET can be done more easily as compared to thyristor because the resistance of MOSFET is increases with increase in temperature. MOSFET have the positive temperature coefficient. In ... the parallel operation of MOSFET can be done more easily as compared to the thyristor.

Description : what are the disadvantages of thyristor?

Answer : Disadvantages of thyristor The silicon controlled rectifier (SCR) is unidirectional devices, so it can control power only in DC power during positive half cycle of AC supply. Thus only DC power is ... cycle. It cannot be used at higher frequencies. The gate current cannot be negative

Description : write short notes on thyristor CSI .

Answer : Current-source inverter (CSI) is an inverter with a DC current input. Current source inverters are most commonly used in very high power AC motor drives.

Description : Adjustable-speed drive

Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Answer : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Answer : For constant torque drive armature voltage control speed control method is preferred.

Description : The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

Answer : The synchronous motor which works on leading power factor and does not drive any mechanical load is called synchronous condenser.

Description : What is the difference between AC and DC drive?

Answer : AC means alternating current It's Frequency is 50hz Dc means direct current ItsI Frequency is 0Hz

Description : What is an electric motor drive?

Answer : An electric drive is a complex electromechanical system that drives various actuators in industrial and industrial work machines. In this case, control is carried out using a technological process ... calculation of the kinematic and load characteristics of the electric drive is carried out.

Description : What is a drive in electrical controls?

Description : What does an electric drive do?

Description : Can a power surge erase a hard drive?

Description : Scherbius Drive System

Answer : Scherbius Drive System

Description : Kramer Drive System

Answer : Kramer Drive System Kramer drive is a rotor side speed control drive of induction motor. Slip is the difference between synchronous speed and rotor speed. It is the ... and DC motor. The static Kramer drive is costlier because of the cost of DC motor.

Description : Advantages of Variable Frequency Drive (VFD)

Answer : Advantages of Variable Frequency Drive (VFD)

Description : Function of OR Gate its logical symbol and truth table.

Answer : Function: - OR gate is used to perform logical addition. So used in adder subtractor and logic circuits where logical Oring is required. Used to implement SOP form equations. Also used in PLA logic. Logical symbol of OR gate :- Truth table:- 

Description : GATE 2020 syllabus electrical engineering

Answer : EE: Electrical Engineering Section 1: Engineering Mathematics Linear Algebra: Matrix Algebra, Systems of linear equations, Eigenvalues, Eigenvectors. Calculus: Mean value theorems, Theorems of ... to dc converters, Single phase and three phase inverters, Sinusoidal pulse width modulation.

Description : Sketch symbol of NAND gate and NOR gate.

Answer : Symbol of NAND gate and NOR gate

Description : What is the propagation delay of a logic gate?

Answer : The application input pulse and the occurrence of resulting output pulse is called propagation delay of logic gate.

Description : What is the purpose of a NAND gate?

Answer : Nand gate has 2 inputs and only 1 output and it is equivalent of an and gate. The output of a nand gate is high(1) only when anyone or both inputs are low(0).and the output of nand gate is low(0) only when both the inputs are high(1).nand gate is also called as universal gate.

Description : What is an inverter gate?

Answer : Not gate is known as inverter gate as it inverts the I/P

Description : What does the AND gate do?

Answer : AND gate multiple two inputs. If any one input is zero output will be zero if both inputs are one then only output is one.

Answer : By using some circuit the forward DC current of thyristor is forced to zero is called forced commutation.

← Prev Question Next Question →
Ask a Question
Choose topic