search
person
What are the desirable characteristics of ideal switch?

1 Answer

Desirable characteristics of the ideal switch:

It is desirable to have power switches characteristics closer to ideal switch. The ideal switch should have the following characteristics.

  1. Zero resistance when the switch is on and infinite resistance when the switch is off.
  2. Instant switch on and instant switch off.
  3. Infinite current conduction in on state.
  4. Infinite voltage capability when the switch is in off state.
  5. Zero leakage current when the switch is in off state.
  6. Zero voltage drop when the switch is in on state.
  7. 100% efficiency.
  8. Able to control power flow with zero power dissipation.
thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Answer : The desirable static characteristics of a measuring system are accuracy, sensitivity and reproducibility.

Description : The desirable properties of transformer core material are  (1) low permeability and low hysteresis loss. (2) high permeability and high hysteresis loss. (3) high permeability and low hysteresis loss. (4) low permeability and hysteresis loss.

Answer : The desirable properties of transformer core material are high permeability and low hysteresis loss.

Description : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken?

Answer : To measure an A. C. voltage by using an A.C. potentiometer, it is desirable that the supply for the potentiometer in taken from the same source as the unknown voltage.

Description : The device which allows reverse power flow and withstands highest switch frequency is (A) GTO (B) MOSFET (C) IGBT (D) Inverter grade SCR

Answer : The device which allows reverse power flow and withstands highest switch frequency is MOSFET

Answer : Yes ,it is one of the main advantage using thristors as a  switch in DC  circuit ,it has a high current gain

Answer : Yes, SCR is a unidirectional switch.

Answer : Because it has a higher switching frequency and heat tolerance.

Description : Draw symbol & V-I characteristics of (i) LASCR (ii) DIAC (iii) TRIAC

Answer : (i) LASCR:  (ii) DIAC:  (iii) TRIAC: 

Description : Draw a symbol and neat labeling V-I characteristics of GTO and explain its operation.

Answer : Ans: Symbol and V-I characteristics of GTO: Operation of GTO: i) As the applied anode to cathode voltage is increased above zero, very small current (leakage current) flows through the device. ... low voltage (VBRR). The reverse breakdown voltage is of the order of 20 to 30 volt only. 

Description : Draw a neat labelling V-I characteristics of SCR and explain the region

Answer : (i) Latching current: It is the minimum anode current required to maintain the SCR in the conduction state just after turn-on and the gate signal has been removed.  (ii) Holding current: It is the minimum anode current required to hold the conducting SCR in the ON state. 

Description : Explain the characteristics of inductor to be considered while designing it. What is the effect of over current and increase in temperature on inductor.

Description : Explain the electrical characteristics of transformer.

Answer : Transformer electrical characteristics: Area of primary and secondary conductors, Apri and Asec: Winding loss Pw: Flux density and core loss: Leakage inductance: ... transformer span. The rise in temperature may breakdown insulation which may cause failure of the transformer.

Description : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

Answer : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

Description : What should be the ideal resistance of ammeter ?

Answer : Ideal resistance of ammeter should be zero.

Description : what is ideal voltage source?

Answer : every voltage source have their own resistance that is called as internal resistance it is because of the resistance of electrodes and electrolytes in the battery interms of other supplyit have ... in universe it means ideal voltage source is this voltage source having internal resistance zero

Description : The gain of an ideal amplifier must be

Answer : The gain of an ideal amplifier must be infinity

Description : An ideal voltage source has?

Answer : An ideal voltage source has zero internal resistance.

Description : An ideal voltage source should have?

Answer : An ideal voltage source should have zero source resistance.

Answer : An ideal traction system should have easy speed control, high starting tractive effort, equipment capable of with standing large temporary loads.

Answer : For any type of consumer the ideal tariff is three part tariff.

Answer : An ideal transformer is one which has no losses and magnetic leakage.

Answer : An ideal transformer will have maximum efficiency at a load such that copper loss equal to iron loss.

Description : What are the characteristics of a capacitor?

Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

Description : What is the difference between a switch and a relay?

Answer : Switch is simply a mechanical contact mechanism and relay is a electromagnetic switch . Switch can be direct mechanically turn on and off but relay can be operated by energising coil .

Description : The following is/are the characteristics of SF6 circuit breakers:  (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

Answer : The following is/are the characteristics of SF6 circuit breakers:  (A) It does not need an auxiliary breaking chamber (B) Short break time of 2 to 2.5 cycles (C) All of the above (D) None of the above

Description : Draw & explain touch plate switch using IC555.

Answer : It is construct form monostable multivibrator , when metal plates touch by finger then voltage at pin number 2 goes to below 1/3 Vcc then output of lower comparator becomes high hence flip flop set and ... then output of timer goes low and it low till up to the metal plates touch by finger .

Description : Give the function of fuse and switch.

Answer : Functions of fuse:  * To break the circuit under fault condition.  * To provide overcurrent protection to the circuit.  * To provide short circuit protection to the circuit.  * To provide ...  * To make the electric circuit manually.  * To break the electric circuit manually.

Description : State the function of : i) MCCB ii) ELCB iii) MCB iv) Switch. 

Answer : i) MCB: Provide short circuit protection & over load protection to electrical loads.  ii) ELCB: Provides protection by detecting the unsafe magnitudes leakage currents flowing to earth and disconnecting ... rating.  iv) Switch: Make and break the electrical connection to the load manually.

Description : Transfer switch

Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : How rating of main switch and cable is selected for Industrial Installation.

Answer : 1. Rating of Main Switch or Fuse Rating is decided in industrial installation: Rating of main switch or fuse is based up the starting current of motor. For calculating starting current is considered 2 ... take 1.5 times the rated current or full load current. & thus cable rating is decided.

Description : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Answer : Earthing switch is used for?  (A) Measuring of safety voltage (B) Protection of equipment from ground faults (C) Discharging residual energies (D) All of the above 

Description : A switch tail ring counter is made by using a single D-FF. The resulting circuit is (A) T-FF (B) D-FF (C) SR-FF (D) JK-FF

Answer : A switch tail ring counter is made by using a single D-FF. The resulting circuit is T-FF

Description : A closed switch has a resistance of?

Answer : A closed switch has a resistance of zero.

Answer : The switch board instruments should be mounted in vertical position.

Answer : If the centrifugal switch of a two-value capacitor motor using two capacitors fails to open then Electrolytic capacitor will, in all probability, suffer break down.

Answer : In a single phase motor the centrifugal switch disconnects auxiliary winding of the motor.

Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Answer : A thermal protection switch can protect against overload.

Answer : BJT act as switch in saturation and  cutoff region ( ON state in saturation region and OFF state in cut-off region )

Description : What is the smallest unit of a compound with the same chemical characteristics?

Answer : The molecule is the smallest unit of a compound with the same chemical characteristics.

Description : Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.

Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

Description : Diode VI characteristics

Answer : Diode VI characteristics

Description :  basic characteristics of sound signal.

Answer : Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio. 

Description : Compare characteristics of asynchronous and synchronous transmission mode (four points). 

Answer : Synchronous transmission Asynchronous transmission 1. Synchronous transmission are synchronized by an external clock. 1. Asynchronous transmission are synchronized by special signals along the transmission ... for transferring a small amount of data as it is simple and economical.

Description : Explain the characteristics of solar cell.  

Answer : Characteristics of solar cell : Explanation :- Solar cells produce direct current ( DC ) electricity and current times voltage equals power, so we can create solar cell I-V curves representing ... system so that it can operate as close to its optimal peak power point (MPP) as possible.

Description : State characteristics of force.

Answer : i) Magnitude: The quantity of force e.g. 10 N, 100 kN etc.  ii) Direction: It is the line along which the force acts. It is also called as line of action of the force.  iii) Point of ... .  Push: If the arrow head is pointed towards the point of application, the nature of the force is push.

Description : List three important characteristics of an electric circuit.

← Prev Question Next Question →
editAsk a Question
...