search
person
What is the voltage in 3 phase line?

4 Answers

415

thumb_up_alt 0 like thumb_down_alt 0 dislike

440

thumb_up_alt 0 like thumb_down_alt 0 dislike

440v


thumb_up_alt 0 like thumb_down_alt 0 dislike

between 430 to 440 v

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : What is line voltage and phase voltage? Draw balanced three phase star connected system. Show all the voltages and currents.

Description : What is the difference between line and phase voltage?

Answer : Line voltage  is  voltage  between two  phases R &Y  (415 v)  while  phase  voltage  is  the  voltage  between  one  phase and  a neutral  B &  N   (240 v).

Description : Write the relation between phase and line current, phase and line voltage for Star connection.

Answer : Line voltage is equal to root three times of phase voltage and line and phase currents are equal in star connection

Description : For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

Description : What is the difference between line and phase current?

Answer : The currents flows through phase lines is called line voltage and currents flows from phase to neutral line is called phase current

Description : For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

Answer : For 11kV line the inductance per km per phase will be of the order of: 1 mH

Description :

Answer : Reactance relay is preferred for phase fault on short transmission line.

Description :

Answer : Impedance relays are used for phase faults on long line.

Description : What is the difference between a line voltage and low voltage control system?

Description : Is the power line voltage available in our homes a dc or an ac voltage?

Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

Description :

Why the read of 3 phase voltage is 440?

Answer : The  read  of  a  phase  voltage  should be approximatly  240v. This  is  because  line  voltage  equals  to quberoot of  phase  voltage.

Description : In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

Answer : In an alternator, at lagging power factor the generated voltage per phase as compared to that at unity power factor must be more than terminal voltage.

Description : Explain the need and steps to conduct the reduced voltage running up test on the three phase induction motor.

Description : Draw the waveform of three phase AC supply voltage.

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

Description : Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Answer : The integral cycle control (on-off control) and phase angle control are the two types of AC voltage controller. The principle of ON-OFF control: The on-off control is also called an integral cycle ... control. In phase control, the switch is on for some period of each cycle.  

Description : What is a three phase connection?

Answer : RYB, 440 volt/phase

Description : The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

Answer : Vscos¢s-Vrcos¢r=IR

Description : For 11 kV line the capacitance per km per phase will be of the order of:  (A) 1 Farad (B) 0.1 Farad (C) 0.01 Farad (D) 0.01 microF

Answer : For 11 kV line the capacitance per km per phase will be of the order of: 0.01 Farad

Description : The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Answer : The power consumed in a circuit element will be least when the phase difference between the current and voltage is 90°.

Description : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Answer : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

Description : The product of apparent power and cosine of the phase angle between circuit voltage and current is?

Answer : In parllpar reasonans RLC circuit the current is

Description : The phase difference between voltage and current wave through a circuit element is given as 30°. The essential condition is that?

Answer : The phase difference between voltage and current wave through a circuit element is given as 30°. The essential condition is that both waves must have same frequency.

Description : While calculating performance of medium transmission line, what assumptions are made in case of (i) Nominal 'T' Method (ii) Nominal 'TT' Method. 

Answer : (i) Assumptions are made in case of Nominal 'T' Method:  a. It is assume that line capacitance is connected at center of transmission line. b. It is assume that half ... assumed that transmission line resistance & reactance per phase is connected in between two half transmission line capacitance 

Description : A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

Answer : A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

Description : What are the losses in a transmission line?

Description : What is a high tension power line?

Answer : High tension power line is a high voltage of 115 kv and power line is underground transimissio used by urbun areas

Description : what is mean by medium transmission line ?

Answer : The transmission line which have length between 80 km to 250 km is known as medium transmission line.

Description : what is mean by short transmission line ?

Answer : The transmission lines which have length less than 80 km is known as short transmission lines.

Description : what is mean by long transmission line ?

Answer : The transmission line which have length more than 250 km are known as long transmission lines.

Description : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

Answer : A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is : 200 V

Description : If 1-phase voltage is 220V, why is 3-phase 440V and not 660V ?

Answer : Phase voltage =220v /( phase to neutral) Line voltage = 380 v ( phase to phase) Phase angle difference 120° So when two phases reach vmax +ve I.e. (+220v) + (+220v) = 440v that time due ... these event happen very fast. Hence we have 440 v only in three phase motor. √3.phase voltage= 380 v.

Description : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is (A) + 120 V (B) – 120 V (C) – 60 V (D) + 60 V

Answer : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is + 60 V

Description : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

Answer : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be : 34.64 kVA

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

Description : List the properties of line insulators in brief

Answer : Following are the properties of line insulators:  A) Electrical Properties of insulating material:- 1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high ... of insulating material:- 1. It should have longer life. 2. It should have low cost

Description : requirements or properties of the line supports used in transmission and distribution.  

Answer : Following are requirements or properties of the line supports used in transmission and distribution. 1. High mechanical strength:-  It should have high mechanical strength to withstand against - ... . 8. Appearance: It should have good appearance or They must be of pleasing shape

Description : HVDC transmission line in India: 

Answer : HVDC transmission line in India:  S.N .  From To  Voltage 1 Rihand (U.P) (from 1990) Dadri +- 500 KV (bipolar) 2 Talcher- is the biggest ... (Chandrapur) Western Region  140KV   8 Connecting Southern region(Vizag- Gajuwaka) Eastern Region 140KV 

Description : Shunt compensation in an EHV line is used to (A) Improve stability. (B) Improve the voltage profile. (C) Reduce the fault level. (D) Substitute for synchronous phase modifier.

Answer : Shunt compensation in an EHV line is used to Improve the voltage profile.

Description : In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

Answer : In a transmission line if booster transformers are to be used, preferred location will be At the intermediate point

Description : A lightening arrester connected between the line and earth in a power system  (1) protects the terminal equipment against travelling surges (2) protects the transmission line against direct lightening strokes (3) suppresses high frequency oscillations in the line (4) reflects back the travelling wave approaching it

Answer : A lightening arrester connected between the line and earth in a power system protects the terminal equipment against travelling surges

Description : Series capacitive compensation in EHV transmission line is used to

Answer : To maintain voltage stability 

Description : The line current in a balanced delta system is 30 A. The load current is (A) 30√3 A (B) 30/√3 A (C) 10 A (D) 30/√2 A

Answer : The line current in a balanced delta system is 30 A. The load current is 30/√3 A

Description : lf a travelling-wave travelling along a loss-less overhead line does not result in any reflection after it has reached the far end, then the far end of the line is

Answer : lf a travelling-wave travelling along a loss-less overhead line does not result in any reflection after it has reached the far end, then the far end of the line is terminated into a resistance equal to surge impedance of the line

Description :

Answer : In main line service as compared to urban and suburban service distance between the stops is more, maximum speed reached is high, acceleration and retardation rates are low.

Description : State the limitations of EHVAC transmission line. 

Answer : Following are the Limitations of EHVAC Transmission:   1. Insulation cost increases as voltage increases 2. Skin effect is more 3. Proximity effect is more. 4. Corona loss increases. 5. Radio ... 18. EHVAC is economical only for bulk amount of power is to be transmitted over long distance. 

Description : State line parameters of transmission line. 

Answer : Following are the of Line parameters of transmission line:  1. Resistance  2. Inductance  3. Capacitance

Description : State the meaning of Single line diagram.

Answer : Meaning of Single line diagram: The single line diagram of a power system is the network which shows the main connections and arrangement of the system components along with their data ( ... breakers, transformers, capacitors, bus bars, and conductors are shown by standardized schematic symbols. 

← Prev Question Next Question →
editAsk a Question
...