search
person
what is the difference between four point starter and three point starter?

1 Answer

The only difference is in the NO VOLT COIL connection in the starter, in three point starter NVC is connected to the field whereas in four point starter it is connected separately. The advantage of using 4 point starter is that it can work well in field controlled motor as well.

If we try to perform field control of DC shunt motor using a 3 point starter, the field current might get very low(for above rated speed) and lead to DEENERGISE the NVC leading to turning off of the motor.
thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description :

Answer : Three point starter can be used for both shunt and compound motor.

Description :

Answer : A three point starter is considered suitable for shunt as well as compound motors.

Description : State any four advantages of soft starter.

Answer : Advantages of soft starter: 1. Very low line voltage drops on motor operation 2. Reduced energy losses in the lines 3. System efficiency increases 4. Very smooth starting & operation 5. As ... may lead to lower MD billing. 13. Less mechanical maintenance. 14. Saving in operating costs.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Description : Which type of starter is used to start the DC motor?

Description :

Why starter is required for starting an induction motor?

Description : What is an auto transformer starter?

Description : What is the best Arduino starter kit?

Description : State function of starter and ELCB. (Earth Leakage Circuit Breaker)

Answer : i) Function of Starter:- 1. To prevent the high starting current OR to minimize the starting current. 2. To give supply failure protection 3. To give over load and short circuit protection ... an installation and cut off the circuit from power supply and avoid electrical shock to the person.

Description : Explain the necessity of starter for D.C. motor. State various types of D.C. motor starter. 

Answer : Necessity of Starter for D.C. Motor: Armature current is given by equation Ia = (V−Eb)/Ra i) If the motor is at standstill or rest, back emf Eb is zero (as Eb= ZNP/(60A), at start speed N ... . Types of D.C. motor starters: i) Two point starter ii)Three point starter iii) Four point starter

Description :

Answer : In a manual shunt motor starter over load relay is connected in series and no volt relay in parallel with the load.

Description :

Answer : A direct online starter is used for starting motors up to 5 H.P.

Description :

Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

Description : A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Answer : The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.

Description : State any four advantages of three phase induction motor. 

Answer : Advantages of three phase induction motor https://youtu.be/27OIOCKN05U

Description : Single point Cutting tool signature

Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Description : The operating point of a protective current transformer is near the

Answer : The operating point of a protective current transformer is near the Ankle point

Description : Blind spot is a point in the zones of protection where

Answer : Blind spot is a point in the zones of protection where No protection is available.

Description : If the % reactance upto the fault point is 20%, then the short circuit current will be

Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

Description :

Answer : In a load curve the highest point represents peak demand.

Description : State any Four lE Rules regarding electric safety. 

Answer :  lE Rules regarding electric safety: 1. IE Rule 3 : Authorization 2. IE Rule 29 : Construction and maintenance of electrical supply line and apparatus 3. IE Rule 30: Service line and apparatus on ... 26. IE Rule 60: Test for resistance of insulation 27. IE Rule 61: Connection with earth 

Description : State any four advantages of LC filter.

Answer : 1. The choke input (LC) filter has a high output D.C voltage. 2. It has no loading effect on the rectifier and power transformer.  3. The diode does not have to carry surge currents.  ... effect on the rectifier and power transformer.  7. It has better voltage regulation than that of π filter.

Description : What are the four basic welding positions?

Description : State any four applications of three phase circuits.

Answer : The application of three phase circuits are 1. Three phase circuit is used for power transmission over long distances. 2. Three phase circuit can produce rotating magnetic field 3. Three phase ... three phase Motors and Transformers. 4. Three phase circuit is used for power converters circuits.

Description : Explain any four properties of Moulding sand. 

Answer : 1. Porosity: Molten metal always contain a certain amount of dissolved gases, which are evolved when the metal freezes the molten metal coming in contact with the moist sand , generates steam or ... to the casting. Refractoriness is measured by the sinter point of the sand rather than its melting

Description : List any four casting defects.

Answer : The various types of casting defects are as follows: 1. Gas Porosity: Blowholes, open holes, pinholes. 2. Shrinkage defects: shrinkage cavity. 3. Mold material defects: Cut and washes, ... Pouring metal defects: Cold shut, misrun, slag inclusion. Metallurgical defects: Hot tears, hot spot.

Description : List any four materials used for pattern making

Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Description : List any four accessories used on lathe.

Answer : The various accessories used in lathe are as follows. 1) Lathe centers 2) Carriers or driving dog 3) catch plates 4) Chucks 5) Face plates 6) Angle plates 7) Mandrels 8) Rests

Description : A four -quadrant operation requires two full converters connected in  (1) Series (3) Back to back (2) Parallel (4) Series Cascade

Answer : A four-quadrant operation requires two full converters connected in Parallel 

Description : Describe the basic SHA operation with the help of its four mode specifications.

Answer : Sample-and-hold amplifier (SHA) is a unity gain amplifier with a mode control switch where the input of the amplifier is connected to a time-varying signal. A trigger pulse at the mode control switch ... but other forms, such as optical and mechanical forms, are possible. Also denoted S/H.

Description : Four Quadrant Operation Of DC Motor

Answer : Four Quadrant Operation Of DC Motor

Description : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Answer : Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

Description : What are three ways you can increase the strength of an electromagnet?

Description : Why is a capacitor used in a single phase motor and not in three phase motor ?

Answer : In 1-phase induction motor capacitor work is generate the auxiliary winding current than excite the main winding to rotor starts rotate. After rotor start rotating about 75% of their speed than auxiliary ... emf to start the motor.so,in 3-phase induction motor is self start induction motor.

Description : Define balanced and unbalanced load in three phase circuit.

Answer : Balanced Load: When all the imedances of 3 phases are equal in magnitude and of same nature then load is said to be balanced.  Unbalanced Load: When all the imedances of 3 phases are not equal in magnitude and of different nature then load is said to be unbalanced.

Description : Why is a three phase denoted by R, Y, B ?

Answer : phase 1 ,R =Red colour cable terminal, phase 2 Y=Yellow colour terminal cable,Phase 3 B=Blue colour cable terminal, N =Neutral. For identification.

Description : List three important characteristics of an electric circuit.

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

Description : When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is (A) 86.6% (B) 50% (C) 57.7% (D) 73.2%

Answer : When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is 73.2%

Description :

In a three-phase supply floating neutral is undesirable because it way give rise to?

Answer : In a three-phase supply floating neutral is undesirable because it way give rise to unequal line voltages across the load.

Description : how can we reverse the direction of rotation of three phase induction motor ?

Answer : The direction of rotation of three phase induction motor can be reversed by plugging i.e by changing any two out of three phases of the supply to the stator of the Induction motor terminal.

Description :

What is mean by plugging in three phase induction motor?

Answer : Plugging in three-phase induction motor means interchanging of any two phases of a stator for quick stopping.

Description : What is a three phase connection?

Answer : RYB, 440 volt/phase

Description : Explain with neat circuit diagrams the procedures to perform no load and blocked rotor tests on three phase induction motor.

Description : Explain the need and steps to conduct the reduced voltage running up test on the three phase induction motor.

Description : List different starting methods of three phase synchronous motor. Explain any one of them.

Answer : Different Starting Methods of Three Phase Synchronous Motor: As synchronous motor is not self starting, different methods of starting are as follows: 1) By using an Induction (Pony) motor 2) ... . The rotor gets pulled into synchronism and starts running at constant speed as a synchronous motor. 

Description : Draw the waveform of three phase AC supply voltage.

Description : State advantages of three phase over single phase.

Answer : Advantages of 3-phase system over 1-phase system: -  1. More output: For the same size, output of poly-phase machines is always higher than single phase machines.  2. Smaller size: For ... are self- starting: The three phase ac motors are self starting, while single phase induction motor are not.

Description : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 

Answer : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 4 percent

← Prev Question Next Question →
editAsk a Question
...