Questions & Answers
Ask a Question
Questions & Answers
Text to speech
Ask a Question
The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the
May 26, 2018
The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is (a) 0.375 (b) 0.75 (c) 1.33 (d) None of these
to add a comment.
Can you give answer to this question ?
Upload an image:
Email me at this address if my answer is selected or commented on:
Email me if my answer is selected or commented on
Privacy: Your email address will only be used for sending these notifications.
to add a comment.
← Prev Question
Next Question →
Welcome to AskOrAnswerMe.com , where you can ask questions and receive answers from other user. Feel free to ask any question. Help everyone by giving best answer to the questions.
The maximum demand of consumer is 2 kW and his daily energy consumption is 20 units. Its Load Factor is
In a power generating station the Demand Factor and Load Factor are 0.5 and 0.2, respectively. If the...
For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed
The three non -inductive loads of 5 kW, 3 kW and 2 kW are connected in a star network between R, Y and B...
A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant
A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy
A generating st ation has a maximum, demand of 20 mW, load factor of 60%,...
A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor...
Explain the concept of following terms : (i) Connected load (ii) Maximum demand
A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the
One 200 KVA transformer has an iron loss of 1 KW and full load Cu loss of 2 KW. Its load KVA corresponding...
A consumer finds that after running 10 kVA equipment on full load for six hours, his energy
Two siblings start from home to go to their respective schools. The brother goes 6 km West, then turns right and goes 3 km and reaches his school. The sister goes 2 km South, then 4 km East, then turns left and goes 5 km and reaches her school. Where is the sister's school with respect to the brother's school?
Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW
An industrial consumer hall a daily load pattern of 2000 KW, 0.8 lag for...
A 1-phase, 7.46 kW motor is supplied from a 400 V, 50 Hz A.C mains. Its efficiency is 85% and power factor is ...
A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply
A meter whose constant is 600 revolutions/kWh makes 5 revolutions in 20 seconds. Calculate the load in kW.
A consumer consume. 600 kWh per day at a load factor of 0.40....
A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor
A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA.
A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...
Power plant having maximum demand more than the installed rated capacity will have utilisation factor?
A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the
In a certain code language, 6532 means ‘change the TV channel’, 8965 means ‘give back the change’ and 1246 means ‘channel the inner energy’. Find the code for 'channel'. Options: 1)3 2)5 3) 6 4) 2
A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at
The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : -
A 3-phase, 11 kv, 50 Hz, 200 kW load has a power factor of 0.8 lag. ...
A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is
The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current?
At maximum efficiency of a single-phase transformer, the load power factor is
A three-phase synchronous motor connected to ac mains is running at full load and unity power factor.
In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at
The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from
Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses
If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.
1 Ton (unit of air conditioning load) in terms of kW is
Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power
For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is
Three capacitors 15µf, 18µf and 12µf are connected in a circuit. Find equivalent capacitance when they are connected in – 1) Series 2) Parallel
Which of the following sorts is quickest when sorting the following set: 1 2 3 5 4
The load of a consumer is generally measured in terms of :
A three-phase star -connected load is operating at a power factor angle ϕ with ϕ being the angle between
MSXML is (1) A Microsoft language (2) XML parser that ships with Internet explorer 5.0...
For a consumer the most economical power factor is generally?
A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each...
In a power plant if the maximum demand on the plant is equal to the plant capacity, then?
When the SCR conducts, the forward voltage drop will (a) 0.7 V at all load current (b) 2 to 2.5 V at all load...
As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100.
If 5000 kW power is transmitted at 220 kV in place of 11 kV, reduction in the value of electric current will be
Install Android APP