search
person
EPROM internal structure

2 Answers

EPROM internal structure

image

•EPROM means Erasable Programmable Read Only Memory.

•It allows to store data and to erased data and add new data means it is erasable and reprogrammable ROM (Read Only Memory).

•It is useful for changing or updating memory.

•Ultraviolet (UV) light is use for erasing data from EPROM therefore these chips are mounted on package which have transparent window.

•It is exposed to Ultraviolet (UV) light for about 20 minutes and quartz window is use.

•EPROM is programmed by forcing small electrical charge on a floating gate.

•EPROM consists of thousands of storage cells.

•Programming phenomenon is called hot electrons injection.

•Floating gate is made from polysilicon material and it is located in memory cell.

•When EPROM exposed to UV light it erased all data from chip means selective data erasing is not possible with EPROM.

•It is same like ROM but it consists of special transistor connected through ground.

•Special transistor is act as switch and it is normally turned off.

thumb_up_alt 0 like thumb_down_alt 0 dislike

EPROM (Erasable Programmable ROM):

EPROM stands for Erasable Programmable ROM.Data is stored in EPROM memory cell as an electrostatic charge on highly insulated conductor. The charge can remain for many years. The figure shows EPROM memory cell consisting of a single NMOS filed effect transistor. 

image

thumb_up_alt 0 like thumb_down_alt 0 dislike

Related questions

Description : Sketch internal design of 4x3 ROM.

Answer : The internal design of 4x3 ROM

Description : Describe IS – 95 forward link channel structure.

Answer : The IS-95 forward Channel structure consists of four types of logical Channels - pilot Channel, synchronization Channel, paging Channel, and forward traffic Channels. Each forward carrier Channel contains one ... . This code is known as the channel identifier. This code is different for each user

Description :

Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

Description : Justify the statements. 1. IGBT uses a vertically oriented structure. 2. IGBT is preferred as a power switch over both power BJT and MOSFET. 3. Punch through IGBT structure are more popular and are widely used.

Answer : 1. IGBT uses vertically oriented structure. IGBT use vertically oriented structure to reduce the resistance and to increase the current flow area. Hence IGBT uses vertically oriented ... DC circuit applications. Hence punch through IGBT structure are more popular and are widely used.

Description : Write down the steps involved for internal thread cutting on lathe machine.

Answer : Steps involved for internal thread cutting on lathe machine  1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on the boring bar adjusted the angle of ... the start. 10) Keep going until the calculated depth of cut has been reached on the top slide.

Description : List the types of Internal wiring in residential installations –

Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

Description : State the concept of internal voltage drop.

Answer : Concept of internal voltage drop: Every practical source offers some opposition to the current due to its internal parts or components. e.g. a 12V battery has electrodes made up of conducting ... internal voltage drop, the terminal voltage of practical voltage source is always less than its emf. 

Description : Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Answer : a) E.M.F : The electromotive force of a battery is defined as the energy spent or the work done in taking a unit positive charge around the complete circuit of the battery i.e., in ... input required to restore the initial state of charge, under specified conditions, is called Watt-hr efficiency.

Description : What is internal voltage drop and terminal voltage?

Answer : It is not permissible to just connect the positive terminal to the negative terminal of a cell with a copper wire. It will overheat and get damaged. This happens because the electromotive force (emf) ... than the nominal voltage (emf) of the cell and this lower voltage is called terminal voltage.

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

Description :

For maximum transfer of power, internal resistance of the source should be?

Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

Description :

Answer : Large internal faults are protected by merz price percentage differential protection.

Description :

Answer : Yes BJT have internal capacitances.

Description : The internal structure of crystals was first studied with which of the following? w) x-rays x) isotopes y) electron microscopes z) lasers

Answer : ANSWER: W -- X-RAYS

Description : Study of internal structure of plant- (a) Morphology (b) Anatomy (c) Cology (d) Taxonomy

Answer : (b) Anatomy  

Description : Draw and explain Internal port structure of Port 0 and Port 1 of 8051 microcontroller.

Answer : Port-0 can be configured as a normal bidirectional I/O port or it can be used for address/data interfacing for accessing external memory. When control is '1', the port is used for address/data ... is not able to sink the current the pin voltage may rise, leading to a possible wrong reading.

Description : Which of the following memories must be refreshed many times per second? (1) ROM (2) Dyanamic RAM (3) EPROM (4) Static RAM

Answer :  Dyanamic RAM

Description : Which one of the following is used as secondary storage system in computer ? (1) RAM (2) Floppy (3) EPROM (4) ROM

Answer : Floppy

Description : A blank EPROM has:  (1) All bits set to logical 0 (2) All bits set to logical 1 (3) Half the total number of bits set to 0 and remaining half to logical 1 (4) Either (1) or (2)

Answer : A blank EPROM has: All bits set to logical 1.

Description : EPROM contents can be erased by exposing it to  A) ultraviolet rays B) infrared rays C) burst of microwaves D) intense heat radiations

Answer : EPROM contents can be erased by exposing it to  ultraviolet rays for 20 minutes

Description : Normally, the FPGA resources are used less than 70% because:  a. Routing becomes excessively complicated b. Power issues c. Clock frequency d. Simulation time increases

Answer : Normally, the FPGA resources are used less than 70% because: Routing becomes excessively complicated

Description : List and describe three general approaches to improve designer productivity.

Answer : Automation: The task of using a computer program to replace manual design effort. The program replaces manual design effort. Synthesis. Reuse: The ... correctness/completeness of each design step. Hardware/software co-simulation.

Description : Explain placement, routing, and sizing.

Answer : Placement: The task of placing and orienting every transistor somewhere on IC. Routing: The task of running wires between the transistors without inserting other wires or transistors. ... wires and transistor provide better performance but consume more power and require more silicon area.

Description : A single FSM can be converted to two smaller FSM. Justify.

Description :

Answer : Common computation models: Sequential program model Statements, rules for composing statements, semantics for executing them Communicating process model ... Object-oriented model For breaking complex software into simpler, well-defined pieces

Description : Explain the advantages and disadvantages of using memory I/O and standard I/O.

Answer : Memory mapped I/O and standard I/O are the two methods for communicating microprocessor with peripherals. Processor talks to both memory and peripheral using the same bus.Two ways to talk to a peripheral. ... of standard I/O is no loss of memory addresses to the use as I/O addresses.

Description : Explain parallel and wireless protocols.

Answer : Parallel protocols: PCI bus (Peripheral Components Interconnect): PCI stands for Peripheral Components Interconnect. PCI bus is used as a communication line to transmit signals and data ... provide the basis for wireless network products using the Wi-Fi brand.

Description : Explain memory hierarchy.

Answer : Memory hierarchy: Main memory is large, inexpensive, slow memory stores entire program and data. Cache memory is small, expensive, fast memory stores copy of likely accessed parts of large ... In memory hierarchy the smaller memory is faster and larger memory storage is slower.

Description : Explain memory write ability and storage permanence with suitable diagram.

Answer : Write ability and storage permanence of memories: Write ability is the manner and speed at which memory can be written. Storage permanence is the ability of memory to hold stored bits ... Holds bits after power is no longer supplied. High end and middle range of storage permanence.

Description : Describe different RT level computational and sequential components used to design single function processors.

Answer : RT-level combinational components:- To reduce the complexity in digital logic, combinational components are used, which are more powerful than logic gates.  Such combinational ... during a clock edge. An asynchronous inputs value effects the circuit independent of the clock.

Description :

Build using minimum number of CMOS gates.

  1. Three input NAND gate.
  2. Two input NOR gate
  3. Three input NOR gate
  4. Two input AND gate
  5. Two input OR gate

Answer : Three input NAND gate. Two input NOR gate Three input NOR gate Two input AND gate Two input OR gate

Description : Explain the various steps involved in designing a custom single-purpose processor.

Answer : A single purpose processor is a digital circuit designed to execute exactly one program. It is also known as co-processor, accelerator or peripheral. It contains only ... for small quantities. Performance may not match general-purpose processors for same applications.

Description : If Moor's law continues to hold, predict the approximation number of transistor per leading edge IC in the year. 1.2030 2.2050

Answer : If Moor's law continues to hold, predict the approximation number of transistor per leading edge IC in the year.1.20302.2050

Description : Compare the annual growth rate of  1.IC capacity 2.Designer productivity.

Answer : Compare the annual growth rate of 1.IC capacity2.Designer productivity.

Description : Explain Inter-process Communication (IPC) using mailbox/queue.

Answer : Inter-process communication using mailbox: Mailbox is the Interprocess communication mechanism. A process puts a data message for another process in the mailbox. Mailbox is also called as message exchange. ... a message. In mailbox IPC the sender need not to know the name of the receiver.

Description :

Explain arbitration. What is priority arbitrator?

Answer : Arbitration: IF multiple peripherals are connected to microprocessor or DMA controller or any resource and they request services simultaneously so which peripheral will get serviced first this is ... Peripherals make requests to arbiter and arbiter makes requests to the resource.

Description :

Explain FSM and concurrent process with example.

Answer : Finite State Machine (FSM): Finite state machine is a machine which have a transition from state to state. The system have some number of states and at a time the system can ... Y seconds. In sequential execution, the processor executes single task which causes poor processor utilization.

Description : Compose 1k x 8 ROMS into 8k x 8 ROM.

Answer : 1k x 8 ROMS into 8k x 8 ROM:

Description : What is design technology? Explain top down design process.

Answer : Design technology: Design technology is the manner in which we convert our concept desired system into an implementation. The three main design technologies are 1. Compilation/Synthesis ... general purpose processors and A Gate-level Netlist for special-purpose processors.

Description :

Explain data transfer mechanism in I2C protocol. Compare it with CAN and USB protocol based on bit rate and area of applications.

Answer : I2C (Inter-Integrated Circuit): I2C stands for Inter-Integrated Circuit. I2C is a serial protocol. It was developed by Philips Semiconductor. I2C bus have two communication lines. One is serial data ( ... Mbps this is used for lower speed devices. Using USB we can connect upto 127 devices.

Description : What is Mailbox? Write a note on Mailbox.

Answer : Mailbox is used for inter-process communication for sending small messages between tasks or between ISR and task. The Mailbox is used in some Real Time Operating system (RTOS). If the task or ... received by which task or thread is called mailbox client. Mailbox message is a kernel service.

Description :

Answer : The volatile keyword is a part of C standard, and this warns the compiler that ISR might change the value of a variable so that the compiler will not optimize the code in a way that will ... the keyword is not supported, you can still get the similar result by turning off the compiler optimizations.

Description : explain how a stepper motor is controlled using driver. give relevant hardware and software details.

Answer : A stepper motor is an electric motor that rotates fix number of degrees whenever we apply a step signal. the stepper motor can rotate 1.8-degree full step or ... driver 2. controlling a stepper motor directly Application of stepper motor: disk driversprintersphotocopyfax machinerobotscamcorder

Description : Explain Keypad controller.

Answer : Keypad Controller: It's a device which interfaces between the computer and keyboard. That is a input device and used for transfer the data to connected device.

Description :

Answer : Liquid Crystal Display:-An LCD is a low-cost, low power device capable of displaying text and images. LCD's are extremely common in embedded systems since such system often does not have video monitors ... toggles the enables bit and acts as a delay so that the command can be processed and executed.

Description :

Answer : UART takes parallel data and transmits serially and UART receives serial data and converts to parallel.A simple UART may possess1.Some configuration registers and2.Two independently operating processors, one ... must write data to the transmit register and/or read data from the received register.

Description :

Answer : Timers:-A timer is a peripheral device that can measure time intervals. Timers can be used to1. General events at the specific time or to determine the duration of two external events.eg. Keeping a ... the number of times the car wheel rotates in one second, in order to determine cars speed.

Description :

Answer : Most microprocessors have a nonmaskable interrupt, an input pin that causes an interrupt that cannot be disabled. If an interrupt routine shares any data with the task code, then it is necessary ... by setting the priority level. 3. It allows us to enable and disable individual interrupts.

Next Question →
editAsk a Question
...